Professional Documents
Culture Documents
LP-01
Issue No. 02
Issue Date: 28-06-12
EASWARI ENGINEERING COLLEGE
Department of Automobile Engineering
Regulation 2019
LESSON PLAN
Unit I Objective: To study the basics of Semiconductors, PN junction diodes, Zenor diodes and its
applications in Rectifier and Voltage Regulations.
1 • Introduction 1 R2 3-6
2 Classification of solids
• Based on energy band theory 1 R2 112-116
• Conductor, Semiconductor, Insulator
3 Intrinsic semiconductors
• Energy band diagram 1 R2 118-125
• Crystal Structure
4 Extrinsic semiconductors
• P type and N type 1 R2 125-128
• Charge density expression
5 PN junction diode
• Structure, Operation 1 R2 129-136
• Energy band diagram
• Characteristics
6 Rectifiers 1 R2 149-152
• Half wave rectifiers – Circuits 161-161
1
• Efficiency, Ripple, Form- factor, PIV
7 Full wave rectifier 153-157
• Center tap rectifier – ŋ, ripple factor, PIV 1 R2 161-162
• Bridge rectifier - ŋ, ripple , PIV
8 Zener diode
• Zener diode characteristics 1 R2 165-166
• Zener effect, Avalanche effect
9 • Voltage regulation 1 R2 167-173
Outcome: Explain the fundamental concepts of
semiconductors and rectifiers.
Total 9
Unit II TRANSISTORS AND AMPLIFIERS
2
Conversion, addition
Weighted and Non weighted codes
24 AND, OR, NOT, NAND, NOR circuits, Exclusive
OR gate 1 R4 864-869
Truth Table, Logics, Symbols
25 Boolean algebra
Postulates 1 R4 870-872
Expression Reductions
Circuit Implementation
26 Adders
Half adder and Full adder –Logic diagram, 1 R4 873-876
TT, Explanation
27 Flip flops
SR, Clocked SR FF, D F/F’s 2 R4 884-887
JK, T F/F’, Master JK FF
28 Registers 1 R4 887-889
SISO, PIPO,SIPO,PISO - Circuits
29 Counters
Synchronous (UP, Down) 1 R4 890-893
Asynchronous Counter (Ripple)
30 A/D Converter and D/A Conversion.
R2R Ladder 1 R4 893-899
Circuit diagram
Formula
fundamentOutcome: Explain the concept of digital logic
circuits and its applications.
Total 9
Unit IV 8085 MICROPROCESSOR
31 • Introduction
32 8085 Microprocessor Architecture 2 T2 96-108
• Register structures R3 921-923
• 8085 Interrupts-classification of interrupts
• Pin details
• Signal description
33 Instruction Set
• Data transfer instructions 2 T2 175-203
• Arithmetic instructions
• Logical instructions
• Branching instructions
3
• Machine control instructions
34 Addressing Modes & Classification by bytes
• Immediate, Register 2 T2 203-206
• Direct, Register Indirect
• Implicit & Examples
• I,II,III Byte instruction & Examples
35 Programming the 8085
• Simple arithmetic operation program 3 T2 210-215
• Decimal Arithmetic, Searching
• Sorting.
Outcome: Explains the fundamental concept of
8085 Microprocessor.
Total 9
Objective: To study the interfacing concepts of input and output devices with 8085 microprocessor and
its applications like Temperature controller, Stepper motor and Traffic Light Controller.
39 Applications 397-400
• Stepper motor 3 R3 408-410
• Temperature control
• Traffic Light Controller
TEXTBOOKS
1. Milman and Halkias,“Integrated Electronics”,Tata McGraw-Hill publishers,1995.
2. Ramesh Goankar, “Microprocessor Architecture”, Programming and Applications with
8085, Wiley Eastern, 1998.
4
REFERENCES
Prepared by Approved by
Mr. V.Dinesh, AP HOD/ECE
5
191ECS421T ELECTRONICS AND MICROPROCESSORS LTPC3003
R2019
OBJECTIVES:
TOTAL: 45 PERIODS
OUTCOMES:
TEXT BOOKS
1. Milman and Halkias, “Integrated Electronics”, Tata McGraw-Hill publishers, 1995.
2. Ramesh Goankar, “Microprocessor Architecture”, Programming and Applications with 8085, Wiley
Eastern, 1998
REFERENCES
1. Malvino and Leach, “Digital Principles and Applications”, Tata McGraw-Hill, 1996
2. Mehta V.K, “Principles of Electronics”, S. Chand and Company Ltd., 1994
3. Dougles V.Hall, “Microprocessor and Interfacing”, Programming and Hardware, Tata McGraw- Hill,
1999.
4. Salivahanan S, Suresh Kumar N, Vallavaraj A, “Electronic Devices and Circuits” First Edition, Tata
McGraw-Hill, 1999.