Professional Documents
Culture Documents
On the topic of using an external SIM card for data, there is an adaptation channel in 5F called "Internal
SIM card; use" with the default setting of "always".
Changing this to "automatic" extends the Data Connection Settings menu and allows entering an APN,
username and password.
The MIB2 detected the required APN automatically based on the SIM card inserted just like older MMI
head units.
__________________________________________________ _____________________
Enable Sports Computer
[17 – Instrument Cluster] [Coding – 07]
Select Long Coding Helper
Select Byte 10
Enable Bit 2
__________________________________________________ _____________________
Disable Seatbelt Warning
[17 – Instrument Cluster] [Coding – 07]
Select Long Coding Helper
Select Byte 0
Disable Bit 2
__________________________________________________ _____________________
Enable Needle Sweep
[17 – Instrument Cluster] [Coding – 07]
Select Byte 1
Select Bit 0
__________________________________________________ _____________________
Tailgate Opening Delay - Via Remote Key Fob
[46 - Central Convenience] [Adaptation - 10]
Scroll down and find channel "Time for opening rear lid with remote control"
Load Stored Value (should be 800 ms)
Enter new value in "ms". Example: 2000
__________________________________________________ _____________________
Lock/Unlock "Chirp"
[46 - Central Convenience] [Coding - 07]
Select Byte 4
Select Bit 6
__________________________________________________ _____________________
Adaption Changes for "Chirps" when LOCKING the car:
[46 - Central Convenience] [Adaptation - 10]
Find channel "(2)-sounder_settings-beeptime_closing_central_locking"
Default Value is "single_beep"
If you want a single "chirp" when you lock the car, leave this setting as is.
If you want a double "chirp" when you lock the car, change the value to "double_beep"
__________________________________________________ _____________________
Adaption Changes for number of "Indicator Flashes" when LOCKING the car:
[46 - Central Convenience] [Adaptation - 10]
Find channel "(3)-Turn Signal control-Confirmation flashing locking central locking; flashing cycles"
Default Value is "1"
If you want a single indicator "flash" when you lock the car, leave this setting as is.
If you want a double indiactor "flash" when you lock the car, change the value to "2"
__________________________________________________ _____________________
Enable "Beep on Unlock"
[46 - Central Convenience] [Adaptation - 10]
Find channel "(1)-central_locking_system-beep_at_opening"
Default Value is "Off"
Change Value to "On"
__________________________________________________ _____________________
Adaption Changes for "Chirps" when UN-LOCKING the car:
[46 - Central Convenience] [Adaptation - 10]
Find channel "(4)-sounder_settings-beeptime_opening_central_locking"
Default Value is "no_beep"
If you do NOT want a "chirp" of any sort when you UN-lock the car, leave this setting as is.
If you want a single "chirp" when you UN-lock the car, change the value to "single_beep"
If you want a double "chirp" when you UN-lock the car, change the value to "double_beep"
__________________________________________________ _____________________
Adaption Changes for number of "Indicator Flashes" when UN-LOCKING the car:
[46 - Central Convenience] [Adaptation - 10]
Find channel "(3)-Turn Signal control-Confirmation flashing unlocking central locking; flashing cycles"
Default Value is "2"
If you want a double indicator "flash" when you UN-lock the car, leave this setting as is.
If you want a single indicator "flash" when you UN-lock the car, change the value to "1"
If you want a NO indicator "flash" when you UN-lock the car, change the value to "0"
__________________________________________________ _____________________
DRL (Daytime Running Lights) On/Off Option in MMI
[09 – Central Elect.] [Coding - 07]
Select Long Coding Helper
Select Byte 2
Select Bit 1
__________________________________________________ _____________________
Enable ability to Rip CD's to MMI "Jukebox"
[5F - Information Electr] [Coding - 07]
Select Long coding helper
Select Byte 24
Select Bit 5
Adaption:
[5F - Information Electr] [Adaptaion - 10]
Module 5F - Information Electr
Scroll down and find channel "(2)-Copy multimedia data-Optical drive"
Load Stored Value (should be set to "Off")
Change to "On"
__________________________________________________ _____________________
Audi Active Lane Assist - Steering Vibration Adjustment
[A5 - Front Sens. Driver Assist] [Adaptation - 10]
Scroll down and find channel "IDE05985-Directional stab. assist ; intensity; steering wheel vibration"
Load Stored Value (should be set to "Medium")
Change to either "Weak / Medium / Strong"
__________________________________________________ _____________________
Lock When Driving
[46 - Central Convenience] [Coding - 07]
Module 46 - Central Convenience
Select Long coding helper
Select Byte 35
DE-Select Bit 0
__________________________________________________ _____________________
Disable "Low Wind Noise" Stop point on Sunroof
[CA - Sunroof] [Security Access]
[Adaption]
Find channel "IDE09451-MAS08937-Travel path-Sliding Position: intermed. pos."
Value should be "Active"
Change to "Not Active"
__________________________________________________ _____________________
Parking Assist Camera - Turn Off Speed
[Adaptation - 10]
Scroll down and find channel "Switch off speed for park assist"
Load Stored Value (should be set to "10 Kph / 6 Mph")
Change to another value. Example "20" (which is about 12 Mph)
__________________________________________________ _____________________
Seat Symmetry + Passenger Seat Control
**You need to do the SAME coding in Modules 06 and 36.**
Select Byte 36
Set Bit 0 to 1
Set Bit 1 to 1 (for hazards to flash)
__________________________________________________ _____________________
Combine the park assist 360 camera view with the OPS (Optical Parking Sensors) In the display
[17 - Instruments][09 - Central Electronics] [Adaptation - 10]
IDE01170-Visual display for park assist
Original Value - with OPS display
New Value - with OPS 360°
__________________________________________________ _____________________
Change ventilated seat cooling fan speeds for each of the 3 setting
**Max increase is 10% over the default setting**
[09 - Central Electronics] [Adaptation - 10]
IDE10322-MAS01366-Seat ventilation; micro adjust.-Stage 3
Stored value 0 %
New Value - 10%
IDE10322-MAS01365-Seat ventilation; micro adjust.-Stage 2
Stored value 0 %
New Value - 10%
IDE10322-MAS01364-Seat ventilation; micro adjust.-Stage 1
Stored value 0 %
New Value - 10%
__________________________________________________ _____________________
Change the Heated Seats temp in each stage
**5 DEGREES + OR - IS MAX VALUE**
[09 - Central Electronics] [Adaptation - 10]
IDE10321-MAS01364-Seat heater: micro adjust.-Stage 1
Stored value 0 °C
IDE10321-MAS01364-Seat heater: micro adjust.-Stage 2
Stored value 0 °C
IDE10321-MAS01364-Seat heater: micro adjust.-Stage 3
Stored value 0 °C
__________________________________________________ _____________________
C to display SQ7 dials
In module 17 go into long coding
Then change vehicle variant to "derivative 2"
Apply changes
Come out of long coding
Choose reset
Then hard reset
Stg 5F
Ajustare
Adaptări funcții auto gen2
- Setați afișarea meniului adblue la „activ”.
- Setați afișarea meniului adblue peste prag la „activ”.
Resetare MMI
Am făcut asta, dar arată doar că „nivelul de umplere” este inițializat, dar nu se
întâmplă nimic după aceea. Fac ceva greșit sau nu funcționează cu mașina mea?
Acum l-am scos din nou, dar există și mai multe „Opțiuni de afișare Adblue”,
trebuie să activez altceva?
Audi A4 B9 2.0TDI, an 02/2016, TSN BFU