Professional Documents
Culture Documents
A.Y. 2023-24
Continuous Assessment: Term Test - |
5 - Blooms ]
Q.No. Question Description co 3, — Marks
\LQ./I (a) | Explain advantages and disadvantages of Finite element analysis. CO1 | Understand 05 l
Q.1 (b) | Describe different applications of FEA. CO1 | Understand 05 J
Q.2 (a) | Pre-Processing, Processing and Post-Processing in FEA. CO1 | Understand 05 ‘
@72 (b) | General Procedure in FEA. COl | Understand | 05 |
Using FEA, analyze the taper bar as shown in figure. The cross | CO3
sectional area to the lefi and right to is equal to 80 mm? and 20 mm?,
Force of 500 N applied at free end. Take length of bar is equal to 60
mm, Take E=210 GPa. Take two e¢lements,
K2=30 W/m°C
K3=70 W/m°C
Department of Mechanical Engineering
A.Y. 2023-24
Continuous Assessment: Term Test - |l
| are as follows: — 35, + 410, — 285, + 323, — 333, + 260, — 365, + 285, - 260 mm2. The
diagram has been drawn to a scale of 1 mm = 70 N-m and | mm = 4.3°. The engine
speed is 900 r.p.m. and the fluctuation in speed is not to exceed 2% of the mean speed.
Find the mass and cross-section of the flywheel rim having 650 mm mean diameter.
The density of the material of the flywheel may be taken as 7200 kg / m3. The rim 1s
rectangular with the width 2 times the thickness. Neglect eftect of arms, ete.
OR
b) The turning moment diagram for a multicylinder engine has been drawn to a scale of
I mm= 1000 N-m and 1 mm = 6°. The areas above and below the mean turning moment
line taken in order are 330, 330, 380. 470, 180, 360. 330 and 280 sq.mm. For the engine,
find the diameter of the flywheel. The mean r.p.m is 130 and the total fluctuation of
speed must not exceed 3.3% ot the mean. Deternune a suitable cross-sectional area ot
the rim of the flywheel, assuming the total energy of the flywheel to be 15 /14 that of
the rim. The peripheral velocity of the flvwheel is 15 m/s
An electric motor is coupled to a machine through multi-plate clutch operating under
v dry condition. The clutch is required to transmit 7.5KW at 740 rpm. The frequency of
operation is 35 in 8 hours. Due to space constraints overall size of clutch is limited to
250mm in radial direction. Design the following components: 1)Input shaft ,2)Output
shaft, 3)Fnction plate - b
Analysis,
OR CO6
Evaluate
b) 7 KW power is transmitted by a multiple clutch at 960 rpm. The plates run in oil and
coefficient of friction 1s 0.075. Axial intensity of pressure is not to exceed 0.15 N/mm2.
Due to space limitations, external radius is restricted to 125 mm.
(1) Determine number of plates and inner radius.
(ii) Design input shaft and output splined shafi.
If the ¢lutches use 6 springs, decide dimensional details of the spring.
dok ok ok R R R ROR RO R R R RO R R X R REX A || (he Dest *% %% %5 oron ko iokokloloh & fokok ook Rk
Department of Mechanical Engineering
A.Y.2023-24
Continuous Assessment: Term Test - I
T
Blooms Marksj
Q.No. Question Description CcO
Ta Xonomy
a) A Rotary disc cam with central transiatery roller follower has following mation:
o Lorward Stroke of 22Zmm in 100° of cam rotation with cycloidal motion
e Dwell ol 50° of cam rotation
e Return stroke of 22mm in 90° of cam rotation with S1IM.
» Remaming dwell to complete the cycle,
Mass ol the follower is 1.5K g and cam shaft speed is 500 rpm. The maximum pressure
angle during forward stroke and return stroke is limited to 25°. The external foree during
forward stroke is 600N and that of return stroke is 100N,
< Find Prime circle radius. Base circle radius.
¢
- Calculate radius of curvature of pitch curve and cam prolile.
s Determine the width of (he cam.
Q. OR Analysis,
L Rotary disc cam with central translatery roller follower has following motion: Evaluate
Forward Stroke of 25mm in 120° ol cam rotation with SHM motion
Dwell of 60° of cam rotation
Return stroke of 25mm in 100° of cam rotation with SHM,
Remaining dwell to complete the cycle.
Mass of the follower is |Kg and cam shaft speed is 600 rpm. The maximum pressure
angle during forward stroke and return stroke is limited to 25°. The external force during
forward stroke is 300N and that of return stroke is SON,
Find Prime circle radius, Base circle radius,
Calculate radius of curvature of pitch curve and cam profile.&+
Determine the width of the cam.
a) The intercepted arcas between the output torque curve and the mean resistance line Analysis,
0.2 of a turning moment diagram for a multicylinder engine, taken in order from one end
CO4
Evaluate
Department of Mechanical Engineering
A.Y. 2023-24
Continuous Assessment: Term Test - ||
o[t |
Time (hrs) 3 2 6
Job 2
Sequence B A D
Time (hrs) 5 3 2
Consider the bill of material for product J and the data given in the CO3 Apply 09
table below. Gross requirements for product J are 300 in week 2 and
250 in week 4. Develop MRP tables for each items for S-week
planning period. Using fixed order quantity sizing rule of 100 for each
items, whenever required.
J(1)
Q.2
L (1) M (2)
Page 1 of 2
Department of Mechanical Engineering
A.Y. 2023-24
Continuous Assessment: Term Test - 1l
: 5 | Blooms
Q.No. Question Description cO Taxouoms Marks
For CST element, the nodal displacement vector u™= (0,0,0,0,2, -0.1). Find
the element stress take E=200 GPa, plate thickness t=5 mm and Poisson’s
- T
ratio=0.3.
- 340.600 |
Sl (a) CO4 | Analyze 10
P
Q.1 (b) CO4 | Analyze 10
A
&
C
Department of Mechanical Engineering
A.Y. 2023-24
Continuous Assessment: Term Test - i
The demand for an item in a company is 15000 units per year. The CO3 Apply 08
company can produce items at a rate of 3000 per month. The cost of
one set up is Rs 450 and the holding cost of 1 unit per month is Rs
0.25. The shortage cost of one unit is Rs 25 per year. Determine
optimum manufacturing quantity and number of shortages. Also
determine manufacturing time and time between set-up.
OR
The consumption of an item is known to be fixed at 5800 units per
year. The cost of processing an order of this item is Rs 500 and
inventory carrying charges work out to 28 percent per annum of the
Q.3 cost of the item. Determine the optimum ordering policy by
considering inputs provided in the table below.
T
Continuous Assessment: Term Test - |l
R
A typical four-Noded rectangular elements is shown in the figure. Derive CO4
TSR
the shape function for the temperature fields If the nodes 1, 2, 3 and 4
are located at the coordinates point (3, 3), (6, 3), (6, 5) & (3, 5)
respectively and the temperature distribution has been computed at
A
each nodes as Ty= 120°C,T,= 65°C, T3= 40°C and T,= 80°C.Compute the
temperature at x=4 and y=4.
o~y
8]
—
{3. 5, (?I 7}
8.3
(5) o X
Find the Natural frequency of axial vibration of a cantilever bar of CO5
.3 (a) uniform cross section of 20 mm? and of length 1m. Take E = 2e5 Analyze 08
N/mm? and density as 7800 Kg/m®. Take two linear elements
Find the Natural frequency of axial vibration of a cantilever bar of CO5
Q.3 (b) uniform cross section of 40 mm? and of length 3 m. Take E = 2e5 Analyze 08
N/mm? and density as 8000 Kg/m®. Take two linear elements
TR AR R R kR R R R ROk A T] the Dest ¥R R KRRk ko ok ok ok ok ok ks o K
Institute Level Elective
(Common for All Branches)
Instructions:
1. Read the questions carefully.
2. All questions are compulsory except for the internal options.
Q.No. in
Questio
|Bloomsvy €O ¢ Max |
l_,ewel.“ pped Marks |
v@ What different types of financial instruments that are traded - Understanding 1 CO1 6 '
in the capital markets?
v3tate difference between Cooperative and Commercial
5 |
2. | Banks Understanding . COJ 6
OR |
What 1s the role of SEBI in capital market?
i “What is meant by Loan against Jewellery? Explain in Brief.
V37 OR | Appiy coz 6
What are different types of loan? Explain in Brief.
*Darshana Auto Components” is selling Automobile spare -
parts. The firm purchased spare parts worth Rs.8, 000 ‘
(inclusive of GST) form wholesaler and sold it to customer.
for Rs.10,000(inclusive of GST). Rate of GST is 28%. Find ‘
|
i)Input Tax and Output Tax . -? Apply CO3 7
ii) What amount of bill the company paid at the time of *
purchase
Blooms
Q.No. Question Description CO Marks
Taxonomy
e
| /@ Describe Recommendation System Life Cycle. CO4 | Understand 05
Q.3 (a) | Case studies on Map Reduce using Java/Python. CO3 | Apply 07
&3 (b) | Describe data analysis tools available in the market. COS | Apply 07
Blooms
Q.No. Question Description CO Marks
Taxonomy
a) A pair of parallel helical gears consists of 20 teeth pinion meshing
with a 100 teeth gear. The pinion rotates at 720rpm. The normal
pressure angle is 20° while the helix angle is 25°. The face width is 40
mm and normal module is 4mm. The pinion and gear is made up of
plain carbon steel with ultimate tensile strength and yield stress are
600 N/mm? and 350 N/mm? respectively and heat treated to surface
Analysis,
hardness of 300 BHN. Calculate power transmitting capacity based on COl 15
Evaluate
strength and wear for service factor of 1.5.
OR
Lb) A pair of spur gear is used to transmit power at 11.39 HP from a
motor rotating at 16 rps to a machine with_approximate reduction ratio
of 3.7 1) Select suitable material for pinion and géar, i1) Determine the
module and tice width of the gear to satisfy strength and wear.
L3) An angular contact ball bearing is used for worm gear shaft to
support a radial load of 8.5 KN and 4.5KN along the axial direction.
The shaft rotates at 35 rpm, Select suitable size of bearing if it is
required to have a life of 29000 hrs with a probability of survival of
93% - : 5 Analysis,
OR co2 10
Evaluate
b) A single-row deep groove ball bearing is subjected to a radial force
of 8 kN and a thrust force of 3 kN. The shaft rotates at 1200 rpm. The
expected life L10h of the bearing is 20 000 h. The minimum acceptable
diameter of the shaft is 75 mm. Select a suitable ball bearing for this
application
o ¢ 30 e oo ol o o o o Ok 2k ok ok 3 3R ke ok ok ol ka0 ik kR KOk All lhe beSt LR EE R RS RERE LSS EA RS R AR E R R LR
Department of Mechanical Engineering
A.Y. 2023-24
Continuous Assessment: Term Test - |
; v Blooms
Q.No. Question Description Co Thspngmg Marks
M (a) | Categories the “V’s” of Big Data with example., COl | Understand 05
Q.1 (b) | Differentiate traditional vs.big Data business approach. COl1 | Analyze 05
Write a Short note on (Any one) CO3
Q.2 (a) e Distributed File Systems. Understand 03
v Physical Organization of Compute Nodes.
Q.2 (b) | Solve any one real-world case studies of NoSQL. CO2 | Apply 05
&3 (a) | Elaborate mapreduce function with example. CO3 | Analyze 07
Q.3 (b) | Write a Mangodb command to perform CRUD Operations. COZ | Apply 07
0.4 (a) Explain' any two types of NoSQL '
architecture i
pattern with CO2 Remember 08
examples.
©.4 (b) | Describe four components of the hadoop system with a diagram. | €Ol | Analyze 08
OB List and elaborate on the various types of costs involved in inventory | CO3 | Understand | 05
management.
Shri Vile Parls Kelavani Marnidal's
DWARKADAS J. EANGHVI COLLEGE OF ENGIREERING
e e o e ot
v o i
03m
For the bar assemblage shown in fig sub;ectnd to an increase in Cos
temperature AT= 60 °C. Analyze and deterrnine the displacements, the
stresses in each element and the reaction at support jfl'N ’ Ef .
/a(-_’
4
Bronse {
Waminimun §
i
Uy 2 1 X1u L
R A
1
NAUNANAA
Steel
wy 117+ |'::"’ /
i - a
l,' 4* l"- oty
AN W
= 60 KN
e
W (a) 1= T8 kN O%
g R
LT ol, {0 |, AU i J
Mt
Fdbl
e
i 4
o
a1 e
Hronse Alumpm Stegd
J 23000 s 12000 sann (A i
i - P
E N3 Gpu 70 Gl iy (.0
st
-
For the truss shown in Figure, solve for the global displacement CO3
B
components of node 3 and the stress in each element. The elements have
cross sectional area A = 1.0 cm? and modulus of elasticity 15 x 10° N/em?
e N
e
Find the stress in each member Forceat3isFx=200N, F,=-100 N
Ao
is b
g.u
B
e B
Q.4 (b)
ey e
Analyze 0%
etk