Professional Documents
Culture Documents
: MNLH24020144
APPLICANT: UNITED PULP AND PAPER CO., INC. JOB NO.: HRT12-00502
KM48 MCARTHUR HIGWAY, IBA ESTE, DATE: 20 FEBRUARY 2024
CALUMPIT, BULACAN
ATTN: ALLEN JAY CANO
SAMPLE DESCRIPTION:
ONE (1) SUBMITTED SAMPLE (10 PIECES) SAID TO BE UPPC LINER PAPER.
TESTS CONDUCTED:
AS REQUESTED BY THE APPLICANT, FOR DETAILS REFER TO ATTACHED PAGES TWO TO EIGHT.
___________________________
MARIA NADYN E. LICLICAN
SENIOR SUPERVISOR – PHYSICAL & CHEMICAL LAB
CENTRAL LABORATORY – PRODUCTS
APPROVED SIGNATORY
rpu
Estimation of measurement uncertainty is available upon request .
PAGE 1 OF 8
This report (including any enclosures and attachments hereof) has been prepared for the exclusive use and benefit of the addressee(s) and solely for the purpose for
which it is intended. The analysis is based solely on the sample(s) submitted by the client. No part of this report should be reproduced, distributed or communicated to any
third party, unless Intertek Philippines provide or express prior written consent. We do not accept any liability if this report has been used maliciously or used for purpose
other than it was originally intended or stated, nor do we owe any duty of care to any third party in respect of this report.
Attention is drawn to the terms and conditions which was agreed and signed upon together with the proposal or test application form.
PAGE 2 OF 8
This report (including any enclosures and attachments hereof) has been prepared for the exclusive use and benefit of the addressee(s) and solely for the purpose for
which it is intended. The analysis is based solely on the sample(s) submitted by the client. No part of this report should be reproduced, distributed or communicated to any
third party, unless Intertek Philippines provide or express prior written consent. We do not accept any liability if this report has been used maliciously or used for purpose
other than it was originally intended or stated, nor do we owe any duty of care to any third party in respect of this report.
Attention is drawn to the terms and conditions which was agreed and signed upon together with the proposal or test application form.
PAGE 3 OF 8
This report (including any enclosures and attachments hereof) has been prepared for the exclusive use and benefit of the addressee(s) and solely for the purpose for
which it is intended. The analysis is based solely on the sample(s) submitted by the client. No part of this report should be reproduced, distributed or communicated to any
third party, unless Intertek Philippines provide or express prior written consent. We do not accept any liability if this report has been used maliciously or used for purpose
other than it was originally intended or stated, nor do we owe any duty of care to any third party in respect of this report.
Attention is drawn to the terms and conditions which was agreed and signed upon together with the proposal or test application form.
ROHS LIMIT:
Restricted Substances Limits
Cadmium (Cd) content 0.01% (100ppm)
Lead (Pb) content 0.1% (1000ppm)
Mercury (Hg) content 0.1% (1000ppm)
Chromium VI (Cr6+) content 0.1% (1000ppm)
Polybrominated Biphenyls (PBBs) 0.1% (1000ppm)
Polybrominated Diphenyl Ethers (PBDEs) 0.1% (1000ppm)
Di(2-ethylhexyl) Phthalate (DEHP) 0.1% (1000ppm)
Dibutyl Phthalate (DBP) 0.1% (1000ppm)
Benzyl Butyl Phthalate (BBP) 0.1% (1000ppm)
Diisobutyl Phthalate (DIBP) 0.1% (1000ppm)
The limits were quoted from Annex II of 2011/65/EU and Amendment (EU) 2015/863 for homogeneous material.
PAGE 4 OF 8
This report (including any enclosures and attachments hereof) has been prepared for the exclusive use and benefit of the addressee(s) and solely for the purpose for
which it is intended. The analysis is based solely on the sample(s) submitted by the client. No part of this report should be reproduced, distributed or communicated to any
third party, unless Intertek Philippines provide or express prior written consent. We do not accept any liability if this report has been used maliciously or used for purpose
other than it was originally intended or stated, nor do we owe any duty of care to any third party in respect of this report.
Attention is drawn to the terms and conditions which was agreed and signed upon together with the proposal or test application form.
SAMPLING
Cd/Pb/Hg PBBs/PBDEs
Cr6+
METAL POLYMERS /
ELECTRONICS
FOR DIFFERENT MATERIAL,
DIGEST THE SAMPLE WITH WEIGH SAMPLE AND
APPROPRIATE ACID *1 ADD ORGANIC
50cm2 SAMPLE BOILING Insoluble/
unknown SOLVENT
WATER EXTRACTION WEIGH A SAMPLE
polymers
and
CONFIRM THE TESTED Soluble polymers electronics
BY SOLVENT
SAMPLES ARE TOTALLY
COOL AND FILTER THE EXTRACTION
DISSOLVED
EXTRACT
ADD NMP, ADD TOLUENE
ULTRASONIC AND DIGESTION
MAKE-UP WITH DEIONIZED EXTRACTION SOLUTION
CONCENTRATE THE
WATER MAKE UP WITH EXTRACT AND MAKE
DEIONIZED WATER UP WITH ORGANIC
AND ADD DIPHENYL- ALKALINE HEAT SAMPLE IN SOLVENT
CARBAZIDE SOLUTION DIGESTION A MICROWAVE
ANALYZED BY ICP-OES OVEN
METAL
ANALYZED BY UV-VIS
PAGE 5 OF 8
This report (including any enclosures and attachments hereof) has been prepared for the exclusive use and benefit of the addressee(s) and solely for the purpose for
which it is intended. The analysis is based solely on the sample(s) submitted by the client. No part of this report should be reproduced, distributed or communicated to any
third party, unless Intertek Philippines provide or express prior written consent. We do not accept any liability if this report has been used maliciously or used for purpose
other than it was originally intended or stated, nor do we owe any duty of care to any third party in respect of this report.
Attention is drawn to the terms and conditions which was agreed and signed upon together with the proposal or test application form.
Remarks:
*2: If sample solution is significantly more intense than 0.13 µg/cm2 equivalent comparison standard, Chromium VI would be
determined as detected, the result of visual observation is positive.
PAGE 6 OF 8
This report (including any enclosures and attachments hereof) has been prepared for the exclusive use and benefit of the addressee(s) and solely for the purpose for
which it is intended. The analysis is based solely on the sample(s) submitted by the client. No part of this report should be reproduced, distributed or communicated to any
third party, unless Intertek Philippines provide or express prior written consent. We do not accept any liability if this report has been used maliciously or used for purpose
other than it was originally intended or stated, nor do we owe any duty of care to any third party in respect of this report.
Attention is drawn to the terms and conditions which was agreed and signed upon together with the proposal or test application form.
Measurement Flowchart:
Sampling
By solvent extraction
ANALYZED BY GC-MS
PAGE 7 OF 8
This report (including any enclosures and attachments hereof) has been prepared for the exclusive use and benefit of the addressee(s) and solely for the purpose for
which it is intended. The analysis is based solely on the sample(s) submitted by the client. No part of this report should be reproduced, distributed or communicated to any
third party, unless Intertek Philippines provide or express prior written consent. We do not accept any liability if this report has been used maliciously or used for purpose
other than it was originally intended or stated, nor do we owe any duty of care to any third party in respect of this report.
Attention is drawn to the terms and conditions which was agreed and signed upon together with the proposal or test application form.
END OF REPORT
PAGE 8 OF 8
This report (including any enclosures and attachments hereof) has been prepared for the exclusive use and benefit of the addressee(s) and solely for the purpose for
which it is intended. The analysis is based solely on the sample(s) submitted by the client. No part of this report should be reproduced, distributed or communicated to any
third party, unless Intertek Philippines provide or express prior written consent. We do not accept any liability if this report has been used maliciously or used for purpose
other than it was originally intended or stated, nor do we owe any duty of care to any third party in respect of this report.
Attention is drawn to the terms and conditions which was agreed and signed upon together with the proposal or test application form.