Professional Documents
Culture Documents
data sheet
creason
perforated plasterboard
product
Installation information
General Requirements
thickness(mm) width (mm) length (mm) weight* (kg/m2)
All ceilings in this section are non-trafficable. Do not walk on plasterboard ceilings!
performance
Limit
Suitable Reverberation Times
dead loads on plasterboard ceilings to 2 kg/m2 for plasterboard spanning 600mm framing centres.
Sound Absorption
Limit dead loads on plasterboard ceilings to 2.5 kg/m for plasterboard spanning 450mm framing centres.
Music2 rehearsals
Aircreason
> Purifying must have an air cavity behind it for itCafeterias
to perform as a sound absorber.
> Plasterboard
CAPT’AIR® technologyinstallations
is added in close proximity toClassrooms
metal roofs (i.e. raked ceiling or with small ceiling
to actively capture formaldehyde,
cavities) require smaller control joint
improving the air quality inside buildings.
intervals or joints left unfilled as they are exposed to larger rates
0 0.2 0.4 0.6 0.8 1 1.2 1.4 1.6 1.8
of thermal expansion and contraction of the roof and/or ceiling framing otherwise cracking of the
Decorative
ceiling and joint peaking is expected.
> Two styles which
Excessive can easily
vibration be ceiling (by the installation of ceiling services, etc) is known to cause jointing
of the
installed, interspersed with
cracking
standard and joint peaking.
plasterboard.
> Locate ceiling services so they do not cut through ceiling framing members, otherwise some
degradation of the ceiling can be expected
Use the Siniat Reverberation time calculator to Siniat Reverberation Time Calculator
assist in determining how much of the ceiling Use Siniat’s Reverberation Time
and or wall area should be covered. Alternatively Calculator by using your phone’s
involve an acoustic consultant, especially for very camera on the QR code.
high ceilings and unusually shaped rooms such as
those with domed or sloping ceilings.
Framing
2
Framing members as per framing tables or structural design up to 600mm maximum. Also refer to
Section 5.1 for more information on ceiling framing.
board dimensions edge type
perforation perforation absorption
design
pattern ratio (%) (ααw/NRC) width length 2 sides
(mm) (mm) tapered
installation
creason must be installed using fasteners only for all wall and ceiling systems. For all plasterboard joints use siniat
paper tape and apply two coats of mastabase or mastalongset, followed by a final coat of mastaglide or mastalite
finishing compound.
Care should be taken during joint-setting to avoid blocking of perforations.
Refer to the Blueprint for complete installation instructions.
painting
Only use roller application for painting creason. Roller application applies a uniform texture over the entire
surface and ensures the paint does not contact the protective mat fixed to the back of the plasterboard.
Spray application of paint is not permitted.
3
All Siniat products have been developed All Siniat plasterboard and metal
to meet the specific needs of the products are available on the Siniat
Australian market. Products manufactured Carbon Neutral Opt-In program to
in Australia comply with quality systems help you meet your sustainability
certified as complying with AS/NZS ISO goals. Visit
9001:2008 and meet the requirements siniat.com.au to find out more.
of AS/NZS 2588, Gypsum Plasterboard.
Disclaimer
Products manufactured and systems designed
by Etex Australia Pty Ltd and branded Siniat,
The following Siniat products have are produced in accordance with the Building
been independently certified by Code of Australia and relevant Australian
Global GreenTag to GreenRate Level Standards. Information in this document is to
A: mastashield, fireshield, fireshield h, be used as a guide only and is subject to project
soundshield, watershield, spanshield, approval as many aspects of construction are
multishield, curveshield, opal, trurock not comprehensively covered. It is also the
and trurock HD. Compliance certificates responsibility of the project to determine if
are available on siniat.com.au. Siniat’s products and systems are suitable for
the intended application. Etex Australia Pty
Ltd will not be held responsible for any claims
resulting from the installation of its products or
other associated products not in accordance
with the recommendations of the manufacturer’s
technical literature or relevant Australian
Standards. Siniat technical information is regularly
updated. To ensure this document is current with
the latest information, visit siniat.solutions
siniat.com.au
warranty
Siniat's products are guaranteed
by a 10 Year Warranty.
For details visit siniat.com.au
technical advice
AU 1300 724 505