Professional Documents
Culture Documents
02 MWp Capacity
Sayoun - Hadhramout
Bid No.: IUS-AF-UWS-SAY-001
BOQ:
Item Unit Price Total Price
Item Details Unit Qty.
No. [USD] [USD]
Bill: 1 # ELECTRICAL WORKS
1 Solar PV Module:
Supply, install, test, and commissioning of solar PV modules, the capacity is not less than 625W
should be comprising of either mono-crystalline or polycrystalline;
- Conformity with CE and IEC 61215, IEC 61730 or equivalent standards;
- Conversion efficiency should be not less than 20 % under STC;
- The PV module shall perform satisfactorily in temperature between – 40 oC to +85 oC;
- The rated output power of any supplied module shall have tolerance of 0~5 W; Pcs 2016 --
- The module shall be provided with a junction box with at less IP67;
- The supplied module DC voltage should be not less than 1000 VDC;
- PID resistance .
2 Solar Inverter
Supply, install, test, and commissioning of three phases pure sine solar inverter meet the follwoing
specifications:
- Input DC open circuit voltage not less than 1000 V;
- Maximum input DC power shall not less than 150 KWp;
- Lower level of MPP voltage shall not greather than 590 V;
- Upper level of MPP voltage shall not less than 1000 V;
- Maximum input current shall not less than 180 A;
- Rated output AC Power shall not less than 100 KW;
- Nominal AC voltage and frequency shall be 400 V / 50 Hz;
Pcs 9 --
- Maximum efficiency shall be not less tham 97.5% ;
- Shall be certified to meet CE and UL marking and complaint with IEC 62109;
- Degree of protection shall not less than IP65;
- Protections required: AC overload , short circuit, overvoltage and overheating;
- Shall allow internet connection for remote monitoring;
4 DC Cabling
Conductor :-Soft annealed tin-coated flexible stranded copper per ASTM B-33 and EN 60228 , TUV
certified, Insulation:-Halogen-free, thermoset polyolefin specifically designed for maximum
flexibility, and Jacket :- Black/Red, low smoke non-halogenated, flame retardant, oil, abrasion,
chemical and sunlight resistant cross-linked compound meeting UL 44, UL 854.
- All cables shall be marked properly according to approved design so that cable can be easily traced
and identified;
Cable ends connections are to be made through suitable lugs or terminals, crimped properly & with
use of cable glands; Note
This item is including the cables , cable trays and cable trenches, as site required.
Cable Tray :-Perforated type Galvanized steel cable trays, cable tray covers, clamping bolts and other
cable tray
accessories such as coupler plates, bends, tees, reducers, vertical elbows in manufactured accordance
with ASTM A653 SS, Grade 33, coating designation G90.
4.1 Cable between PV module strings and Combiner box: 1.5kV (1C*10 sqr.mm) (Red& Black) L.m 12,168 --
4.2 Cable between combiner boxes and solar inverters 1.5kV(1C*185 sqr.mm) (Red& Black) L.m 1,046 --
5 AC Cabling
Supply, install, test, and commissioning of AC Cabling Stranded type, double insulationg material
XPLE/PVC/CU
- All cables shall be marked properly according to approved design so that cable can be easily traced
and identified;
- All outdoor exposed wiring to be protected from UV radiation and physical damage, all cabling
above ground should be suitably mounted inside cable trays with proper covers;
- XLPE insulated and PVC seathed single or multi core flexible copper cables meeting IEC 60227 and Note
IEC 60502 or equivalent;
- Cable ends connections are to be made through suitable lugs or terminals, crimped properly & with
use of cable glands;
This item is including the cables , cable trays and cable trenches, as site required.
5.1 4C*150 sqr.mm 1kV include remove tiles and excavation trench as per site condition L.m 90 --
5.2 1C*630 sqr.mm 1kV include remove tiles and excavation trench as per site condition L.m 760 --
5.3 3C*50 sqr.mm 11kV include remove tiles and excavation trench as per site condition L.m 100 --
6 Earthing Sysem
Supply, install, test and commissioning Earthing System as per technical specifications and drawings
including cabling, cable lugs, earthing rods and all required acccessorries
- Each array structure of the PV modules should be grounded properly;
- All metal casing/shielding of the system and its components should be thoroughly grounded;
-Earthing pit
- Earth resistance should be tested by calibrated earth tester, the earth resistance should not be more
than 5 Ohm. system 42 --
- Earthing installation in accordance with the IEE Wiring regulations, BS 7671
- All conductive materials shall be copper.
- The size of conductor shall be according to table 54.7 of IEE – BS 7671 – IEC 60365-5-54. (see
Annexe : 07 & 08).
7 Lightning System
Supply, install, test and commissioning Lightening Protection System As per technical specifications :
- lighting arrester shall be copper.
- All metal casing/shielding of the system and its components should be thoroughly grounded;
-Earthing pit
- Earth resistance should be tested by calibrated earth tester, the earth resistance should not be more
than 5 Ohm.
- Earthing installation in accordance with the IEE Wiring regulations, BS 7671 system 24 --
- All conductive materials shall be copper.
- The size of conductor shall be according to table 54.7 of IEE – BS 7671 – IEC 60365-5-54. (see
Annexe : 08 ).
9 CCTV System
Supply, install, test and commission of CCTV system as per technical specifications :
- Contractor shall provide it with whole required data as specification and drawing.
- Shall include all required Switches/ Hubs, connectors, adapters, fittings, accessories, connections and
configurations.
- Should be controlled locally, and available from a remote location through an internet connection.
- A Combination of speed dome cameras (D1 resolutions, min. 36x optical zoom) and fixed IP
cameras (min 29 x optical zoom) to protect continuously the perimeter of the fence when no activities
on the Buses. LS 1 --
- 30 days recording memory of all images on which motion has been detected.
- Camera monitoring screen to be installed in the control room and switchgear room , it has to be
monitored at the same time.
10 Transforming system
Supply, install, test and commissioning of Setp-Up Transformer , which shall be sutiable to use with
solar energy as these specifications : 1250KVA, 0.415/11kv, ONAN, Off LTC, (±3×2.5%), 50HZ,
3phase distribution transformer with copper winding. The transformer should be suitable to be used
together with solar energy. The transformer should be provided with cable boxes on both 11KV &
10.1 0.415KV sides cables box on low voltage side should be suitable to receive cables as per drawings. Pcs 1 --
Conformity with CE and IEC 60076,BS148,BS 171 or equivalent standards;
11 TOTALIZER BOARD
Supply, install, test and commissioning of distribution board, (TOTALIZER BOARD) should be
suitable to accommodate:
- Rated Busbar Current : not less than 2500A.
- Sutibale to recive at less 12 feeders
- Main Breaker: 2000A, 4 poles circuit breaker Adjustable Setting Tp .
- 9 RCBOs : 200A,4 poles circuit breaker with differential device
- 1 MCCB : 40A,4 poles circuit breaker
- 1 MCB : 16A,2 poles circuit breaker
- Indoor PVDB with protection not less than IP55
11.1 - Rated voltage not less than 1000 V AC Pcs 1 --
- Rated frequency 50Hz
- The dimensions should be according to latest issue IEC & BS standardsfor size.
- Breaking capacity at all rated current is not less than 120 KA.
- Limits of time current characteristics according to latest issue IEC & BS standards.
- Cut-off current characteristics according to latest issue IEC & BS standards.
- It characteristics according to latest issue IEC & BS standards.
13 Weather Station
Supply, install, test and commission of weather station for Solar system compatible with Data
Manager and Controller, includes all sensors required to monitor the Solar PV Plant, Irradiance
Sensor, Humidity and Ambient Temperature Sensors,.etc , as per technical specifications :
- Two Pyranometer must be included one horizontal and second tilted, with measurement range
0~2000W/m
- Wind speed sensor shall has a measurement range not less than 0 ~ 70 m/s and starting wind speed
not less than 0.3 m/s
- A pair of wind direction shall have measurement range not less than 0 ~ 360 deg and starting wind Pcs 1 --
speed not less than 0.5 m/s
- Environment and PV module temperature sensor shall have measurement range not less than -50 ~
+100 C .
Supply, install, test and commissioning ligthing System as per technical specifications :
-It shall be All in One Solar Street Light.
- 3 lighting modes with PIR motion sensor.
- Lumens not less than 10000lm.
- Protection not less than IP 65.
- Discharging temperature -20℃~60℃
14.2 - Charging temperature 0℃~55℃ Pcs 4 --
- Switch light sensor ≥50 Lux, OFF. ≤10 Lux, ON.
- Power Li-ion battery, support 1500 cycles
15 Trenches
"Excavation (in all types of soil, tiles , concrete,stone, Asphalt and Asphalt pavement, etc) and backfill
of cable trench with cross section size of 90cm depth and 80cm width including all required civil
works as per drawings.
15.1 The items include disposal of surplus excavated materials outside to any unobjectionable place to be LS 194
identified by contractor at his own cost , The item includes reconstruction the top layer with approved
materials to its original condition.
Supply, install, test and commission of Manholes 1mx1m including all required civil works as per
15.2 Pcs 14
drawings
16 Other Components
Supply, install, test and commission of Fire alarm system including all requirements from
16.1 fire resistant cable, trunkeys ,metal conduit pipes , termination, testing and proper labeling note
with complete Diagrams & documentation.
Supply, install, test and commission of one LOOP Addressable Fire alarm system panel
including all requirements from fire resistant cable, trunkeys ,pipes, termination, testing and
proper labeling with complete Diagrams & documentation.
Technical Specifications:
16.1.1 - 2 LOOP panel No 1
- Each LOOP support to install at least 15 detector.
- 2 sounder circuits
- Include back up battery
- EN54 Approved from LPCB
Supply, install, test and commission of Flame Detector including all required fire resistant
cable
Technical Specifications:
- Operating voltage: 24 VDC nominal (18-32 VDC) - regulated
- Detects hydrocarbon and non-hydrocarbon fuel fires in all environmental conditions
- Alarm Current ≤ 32 mA
16.1.2 - Dual microprocessors for reliable performance No 1
- Sensitivity according to EN 54-10
- Field of view: 90° full 100% core of vision, ± 45° from on axis.
- Sensitivity: Very high, high, medium and low - switch selectable.
- Humidity range: 5 to 98% relative humidity, non-condensing
- Test lamps for manual testing.
- EN54 Approved from LPCB
Supply, install, test and commission of smoke and heat Detector including all required fire resistant
cable
Technical Specifications:
- Operating voltage: 24 VDC nominal (18-32 VDC) - regulated
- Alarm Current ≤ 32 mA
- Dual microprocessors for reliable performance No 9
16.1.3 - Humidity range: 5 to 98% relative humidity, non-condensing
- Test lamps for manual testing.
- EN54 Approved from LPCB
Supply, install, test and commission of Addressable bells(sounders) including all required
fire resistant cable
Technical Specifications: No. 3
16.1.4 - Nominal voltage 9 - 28 Vdc
- Purpose-made weatherproof range.
16.2 Supply, install, test and commissioning 5kg Carbon Dioxide (CO2) Extinguisher Pcs 5 --
16.3 Supply, install, test and commissioning 6kg Powder Extinguisher Pcs 5 --
Supply, install, test and commissioning of Spilt Air Condition inverter type include alternate
operation and temperature control unit and all wiring requirements
- Adjustable fan speed.
- Split unit inverter type.
- Capacity: 24,000 BTU (2 Ton).
- Voltage: 220-240.
- Frequency: 50 Hz.
16.4 - Single phase. Pcs 3 --
- Noise level shall not exceed 45 db.
- Star rating 3 star or above.
- Full inverter versions
- Suitable for wall mounting
- Outdoor unit shall be housed inside metal gage made of mild steel
Supply, install, test and commissioning of LED lighting fixture (20 W) 1200 mm length include its
16.5 Pcs 12 --
switches as per drawing, include all accessories and installation requirement (PVC Pipe, Wiring,…etc.)
Supply, install, test, and commissioning of 13A electrical socket as per drawing, including all
16.6 Pcs 6 --
accessories and installation requirements (PVC Pipe, Wiring,…etc.)
Supply, install, testing and commissionining of Wall mounted exit sign luminaire with 1x8W, led lamp and with
16.8 single sided pictogram including all conductors, conduits, boxes, switches and all related accessories as the pcs 2.0 --
technical specifications and shown on the drawings.
Supply, install, testing and commissionining of wall mounted emergency lighting fixture not less than 90Lm ,not
16.9 less than 9W, LED lamp with 3HRS NI-CD batteries backup including all conductors, conduits, boxes, switches No 4.0 --
and all related accessories as the technical specifications and shown on the drawings
17 Maintenance Tools
Supply, test and commissioning of a Maintenance Tools as per technical specifications include the
following :
- Measuring devices that using for maintaining purpose as: Multi-meter, I-V Curve tracer, earth
resistance tester and Insulation meter.
- Inspection tools as: Infrared Camera (Two IR Cameras should be provided) .
- Two sets of special tools and gauges required for the maintenance of the Plant; Bidder shall sunmit a
detailed list.
17.1 - One set of special lifting and handling appliances required for the maintenance of the Plant. LS 1 --
- The Bidder shall quote his price for tools as specified and recommend any additional tools that may
be required.
- Each tool or appliance is to be clearly marked with its size and/or purpose.
- The tools and appliances supplied shall not be used for erection purposes by the Contractor and shall
be handed over in new condition.
18 System Maintenance
18.1 2 years of preventive maintenance for all facilities. LS 2 --
19 System Training
The contractor will be responsible for providing training course focusing on system operation,
19.1 maintenance and management, the scope of training and schedule shall be proposed by the contractor LS 1 --
and approved by UNOPS engineer.
Sub-Tota: 1 # -
Sayoun - Hadhramout
Bid No.: IUS-AF-UWS-SAY-001
BOQ:
Item Unit Price Total Price
Item Details Unit Qty.
No. [USD] [USD]
Bill: 2 # CIVIL AND STRUCTURAL WORKS
1 Site Preparation
Survey and identify all obstructing components for removal and relocation. Provide protection, temporary utilities, chemical toilets,
scaffolding as required for the implementation of the works and take all measures needed to implement health, safety and security
on site . The item includes removal and relocation of all obstructing components, the planning and implementation for any works
LS 1 --
needed to continue the electricity . It also includes laying a small white stones all around the site to improve the system efficiency
and improve site drainage system
3 Control Rooms
Excavation
A-
All excavations are measured net, with no allowance for timbering, blanking or increase in bulk after excavation, nor for
any working space, all of which the Contractor shall include in his Tender price for excavation.
B- Excavation for foundation, trenches, etc. shall be measured from the reduced level not from the existing level when site
leveling is below the natural level and measured from natural ground level not from site leveling when existing leveling is
over natural level.
C- Excavation for foundation of retaining walls has to be measured net according to previous preamble and to be
calculated from the lower reduced level and not from the higher reduced level and from the natural ground level when
this level is lower than the lower reduced level (from both sides).
3.1 General and foundations Excavations:
Carry out general site leveling and foundations excavations of all types, tie beams and underground structures for areas
where needed in all types of soil, concrete and any pavings, the price include demolishing and removing concrete tiles,
concrete slab on grade curbstone crushed stone base course , all asphalt layers , subbase , base course , wearing
course , gabion stone wall and all the layers under it to reach the levels needed according to execution drawings.and
remove materials from site.
The Contractor's unit price shall include excavation to all depths as required and according to the levels and dimensions
in Drawings, support and protection offside of excavation from falls, backfill, compaction,and removal from Site of all
surplus materials, and all necessary plant and its mobilization to and from Site including maintenance and labour. and
the price include back filling with a suitable materials imported from outside the site and at the contractor expense, to
reach the level of subgrade and as specified in special technical specifications with 200 mm thick layers watering and
compacting to 95% of standard Proctor according to the field density test for the suitable fill materials and the removal of
the extra and unsuitable materials.The price include removing the agricultural soil of group classification (A6, A7) and if
the soil of the excavation is not suitable for back filling the contractor must improve the soil by adding selected fill
materials from outside the site without any extra payments, and if the soil of the excavation is not sufficient for back
filling, the contractor must import selected granular fill from outside the site and at the contractor expense, and without
any extra payments.The price of this Section include Making a soil inspection by the contractor after excavation at
extension area and compare the actual optained bearing capacity with the design bearing capacity , the inspection
must be achieved by a specialized and skilled office. The contractor should submitt the results of the inspection to the
UNOPS Engineer officially befor any work.
3.1.1 a- Bulk excavation For site leveling for internal and external works. ( to the bottom of base course level) m3 22
3.1.2 b-For foundation m3 18
3.2 Crushed stone base course:
Supply , lay and compact crushed stone base course, 95 % dry density after compacting of 15 cm . thickness over the
compacted soil for internal works. m2 65
3.4 Build up Control Room completely with supplying all required materials. It covers all civil engineering and building works
required for the construction of control room and the necessary accessories as technical specification and drawing details (see
drawings S007 to S011 ).
Concrete works:
concrete shall be measured net as executed according to Drawings and / or the UNOPS Engineer's instructions, but no deductions
shall be made for the following:
-Volume of steel reinforcement.
- Electrical and mechanical conduits and pipes embedded into concrete.
-Voids not exceeding 0.1 m in area and 0.05 m in volume.
Unit price for concrete as inserted for each Section shall include the following unless otherwise mentioned:
-All labor, materials, and plants necessary to execute the Section as described included all carriage handling, cutting and waste and
all incidental charges and expenses.
-work to all sectional areas and all thickness forming all holes and mortises, chases, grooves chamfers, etc., according to Drawings
or the UNOPS Engineers instructions, dowels, bolts in pipe sleeves, plugs hold fasts, pipes, ducts tucks.
-Forming slopes, falls and the like and leaving surfaces with the proper finish to exposed surfaces, or ready for screeds and paving.
-Forming the necessary construction joints in the normal course of the works including the suitable water stops and other materials
needed.
3.4.1 -All grading, tamping and trawling.
-Curing as specified and as needed.
Protection of concrete surfaces.+
-Form work scaffolding, strutting and propping for all types of concrete unless otherwise mentioned, including materials and
workmanship, supporting regardless of height, design of form work, and all cuttings of forms to profiles and shapes.
-Solid, fair face, waffle and through slab soffits be considered as ordinary form work for which no extra over shall be paid.
-Concrete works in this section are applicable where needed as drawings.
Blinding unit rate shall cover all excavation, removal of debris, and backfilling works costs.
-Slab on grade unit rate shall cover the cost of [Supply , lay and compact crushed stone base course, 95 % dry density after
compacting of 15 cm . thickness over the compacted soil for internal works]
Supply and cast in situ plain concrete under footings (Cube Fc'=20MPa), conformed to ACI-318M codes requirments.
The works include supply and execute:_ Cement (ASTM C 150), Aggregates (ASTM C 33), Clean water, _ Formworks._ Curing.The
3.4.1.A rate includes all material,equipments,labor..etc, and doing every temporary or Permanent necessaries to finish the item as per m2 35
drawings,specifications and instruction of Engineer in charge.
Reinforced Concrete Class'20' for Slabs, FCU= 200 kg/cm2 for ground slabs, on grade internall works, Price shall include all
3.4.1.B required constructions joints. m3 11.25
a- 15 cm thick.
Supply and provide Reinforced concrete , (Fc'=25MPa), conformed to ACI-318M codes requirements.
The works include supply and execute:_ Cement (ASTM C 150), Aggregates (ASTM C 33), Clean water, _ Formworks._ G40
(fy=280Mpa) Deformed steel bars as drawings ._ Curing._ Bituminous insulated layerThe rate includes all material, equipments,
3.4.1.C labor..etc, and doing every temporary or Permanent necessaries to finish the item as per drawings,specifications and instruction of m3 11.5
Engineer in charge.
a) for footings, ground beams,neck columns, walls under S.O.G and where needed.
Supply and provide Reinforced concrete , (Fc'=25MPa), conformed to ACI-318M codes requirements.
The works include supply and execute:_ Cement (ASTM C 150), Aggregates (ASTM C 33), Clean water, _ Formworks._ G40
(fy=280Mpa) Deformed steel bars as drawings ._ Curing._ Bituminous insulated layerThe rate includes all material, equipments,
3.4.1.D labor..etc, and doing every temporary or Permanent necessaries to finish the item as per drawings,specifications and instruction of m3 18
Engineer in charge.
a) for slabs beams ,Lintel beams, above S.O.G , and where needed.
Supply and provide Reinforced concrete , (Fc'=25MPa), conformed to ACI-318M codes requirements.
The works include supply and execute:_ Cement (ASTM C 150), Aggregates (ASTM C 33), Clean water, _ Formworks._ G40
(fy=280Mpa) Deformed steel bars as drawings ._ Curing._ Bituminous insulated layerThe rate includes all material, equipments,
3.4.1.E labor..etc, and doing every temporary or Permanent necessaries to finish the item as per drawings,specifications and instruction of m3 2.85
Engineer in charge.
a) for columns , walls, above S.O.G , and where needed.
Provide and construct automatic-made hollow concrete blocks (20*20*40)cm for room walls. The rate includes all material,
equipments, labor..etc, and doing every temporary or Permanent necessaries to finish the item as per drawings,specifications and
3.6 instruction of Engineer in charge. m2 764
Supply and laying internal plastering for walls and ceiling . The work includes metal meshes, metal edges, plastering composed of
2 coats, a rough bond coat (1cement:1coarse sand), and a finishing coat using cement mortar consist of (1cement : 3sand),The rate
includes all material, equipments, labor..etc, and doing every temporary or Permanent necessaries to finish the item as per
3.7 m2 810
drawings,specifications and instruction of Engineer in charge.
Supply and laying external plastering for external RC elements and parts of walls . The work includes metal meshes, metal edges,
plastering composed of 2 coats, a rough bond coat (1cement:1coarse sand), and a finishing coat using cement mortar consist of
(1cement : 3sand),The rate includes all material, equipments, labor..etc, and doing every temporary or Permanent necessaries to
3.8 finish the item as per drawings,specifications and instruction of Engineer in charge. m2 857
Supply and apply oil paint (High Quality) for internal walls (2 coats).
The works include supply and install:_ Substrate preparation, cleaning surfaces of dust, dirt, stuck, ... Etc,, priming, puttying 2
faces and polishing.The rate includes all material, equipments, labor, .etc, and doing every temporary or Permanent necessaries to
3.10 m2 764
finish the item as per standards, specifications and instruction of Engineer in charge.
Supply and apply weather resistant Paint (High Quality) for external Plaster (2 coats).
The works include supply and install:_ Substrate preparation, cleaning surfaces of dust, dirt, stuck, ... Etc. priming The rate includes
all material, equipments, labor, .etc, and doing every temporary or Permanent necessaries to finish the item as per standards,
3.11 m2 857
specifications and instruction of Engineer in charge.
Supplying and implementing galvanized stacking iron doors, D1 (2.0m*2.2m) of thickness 1.5mm stacking and welding in an
excellent way without lower or upper joints ,The price includes sanding, welding and rust-resistant paint,Three thick sides, then the
3.12 approved external color, provided that the supply and installation takes place according to the drawings and instructions of the m2 4.4
supervising engineer
Supply and implementation of aluminum windows, W1 (1.0m*1.5m) (1.2 mm thick) with a throat section of 4.5 cm * 5 cm, a
section
The door is 4 cm wrapped, including the hidden locking handles, large hinges, glass rails and rings.
The shutter, and that the installation is done on an iron spreader of 2 mm thickness at the installation areas, and the space around
the throat is filled with material
3.13 The silicone is of a German quality according to the color, and it must be taken into account that the water drainage holes are m2 1.5
placed in the middle of the lower throat of the shutter
And that the supply and installation takes place according to the drawings, technical specifications, and the instructions of the
supervising engineer
A 12 kg fire extinguisher
by number: Supply and installation of a 12 kg fire extinguisher with a sensitive hose of excellent quality, and it must be installed in
the back wall of the room, and the number of one extinguisher for each room
3.16 The price includes everything necessary to implement the item according to the drawings and instructions of the supervising NO 2
engineer
Filling by soil:
In cubic meter:Backfilling with good soil free of organic matter. It is necessary to backfill the sides of the ground tank
either from the excavation product or imported from outside the site on layers not exceeding 30 cm with tamping and
4.3 spraying until obtaining a compaction rate of not less than 90% according to the levels specified on the drawings and m3 44.5
transferring the soil in excess of Backfilling outside the site according to the drawings, specifications and instructions of
the supervising engineer.
Suction fan
4.14 by number: Supply and installation of Suction fans of excellent quality and the price includes all that is necessary to implement 4
the item according to the drawings, specifications and instructions of the supervising engineer. NO
plaster work
In square meter: supplying and implementing cement with a thickness of 3 cm due to the necessity of plastering the internal &
external walls of the room. Price includes spatter, rough base coat and smooth finish. Excellent cement mortar with a mixing ratio
of 1:3 (sand:cement) with water sprayed three times a day for a period of time. not less than five days
4.15 The price includes everything necessary to implement the item according to the drawings, specifications, and the instructions of m2 128
the supervising engineer
Tile workers
In square meter: Supply and installation of Mosaic tiles(25*25*3cm) marble of homogeneous color
White cement more than half the thickness and free of defects shall be installed using cement mortar with mixing ratio
1:3) (sand: cement) over a layer of sand or helix, adjusting the weight and straightness using the crosses and the price)
Includes materials, workmanship, grouting, cleaning, polishing, and everything needed to finish the item according to the
drawings
4.16 and specs. m2 18
Isolation works
By square meter: Supplying and implementing an insulating layer for the room floor slab, ceiling and all concrete surfaces directly
4.17 exposed to soil or any place specified by the engineer. It consists of two perpendicular layers with the necessary tests according to m2 70
the drawings, specifications and instructions of the supervising engineer.
A 12 kg fire extinguisher
by number: Supply and installation of a 12 kg fire extinguisher with a sensitive hose of excellent quality, and it must be installed in
the back wall of the room, and the number of one extinguisher for each room
4.18 The price includes everything necessary to implement the item according to the drawings and instructions of the supervising NO 2
engineer
5 Fence Structure
Supply and install Chain Link Metal Fence with Barbed wires as per in the drawings and the technical specifications, the work
includes the following:
• Survey and conduct all site settlement and levelling such as cut and backfill in any type of soil, and clear all planned areas for the
work from materials, debris, trees, chairs and disposal of debris to authorized area prior to the commencing of work.
• Provide materials and construction of 2.50-meter-high chain Link Fence made from hot dip galvanized coated with pvc coated
Post that shall be embedded in (50X50X50 cm3) reinforced concrete footings and pressed at end. The panels width is 4 meter. The m 486 --
chain link comprise 50mmx50mm openings. the work includes installing of three lines of Barbed Wires above.
• Provide materials and construction of 6m wide double leaf gate as shown on the drawings and according to the technical
specifications and instructions of the supervising Engineer includeing 600X50X20 cm3 reinforced concrete beam.
6 Cleaning System
Supply, install, test and commissioning of a Solar Panel Cleaning System as per technical specifications include the following :
- Contractor shall provide a details drawings and specifications for the system including piping , distribution networks and water
tanks.
- The system shall have an Automatic Double Head Solar Panel Cleaning Brush.
- The brush Shall be a dual power model, which can powered from lithium battery and source of 220V. LS 1 --
-Brush's Pole shall manufacture of carbon fiber arbitrary expansion length up to 7.5 m.
-At least Ten of Automatic Double Head Solar Panel Cleaning Brush should be provided .
Sayoun - Hadhramout
Bid No.: IUS-AF-UWS-SAY-001
BOQ:
Total Cost
# Bill: No. Description
[USD]