Professional Documents
Culture Documents
'!1 '!
Instruction for model assembly
30 12
PAGES OF ASSEMBLY PAGES
TEMPLATES INSTRUCTIONS
MODEL SIZE: 70 x 46 x 21 cm
To make a sculpture yourself, you need to print the templates on the cardboard. The minimum paper weight
825 824 679
866
862
694
681
Todos los derechos reservados. Sólo para uso personal! Copiar, compartir, transferir, publicar y vender están estrictamente prohibidos sin mi autorización.
687
861
688
686
Copyright © 2022 Daniel Paper Art. Todos los derechos reservados
36 37
856
863
867
Todos los derechos reservados. Sólo para uso personal! Copiar, compartir, transferir, publicar y vender están estrictamente prohibidos sin mi autorización.
693
680
695
689
44
used must be at least 200 to 240 / m2. Using thinner paper will cause parts to warp.
46
692
682
694
690
864
868
Copyright © 2022 Daniel Paper Art. Todos los derechos reservados
614
691
693
691
683
692
623
865
869
640
854
680
698
690
684
854
639
685
CINEMA
48
3/63
682
697
CINEMA
4/63
©DANIEL PAPER ART – 2022
683
696
CINEMA
699 647
5/63
©DANIEL PAPER ART – 2022
Rule
A ruler is needed to cut the parts and bend the fold lines evenly. We recommend using a
metal ruler 20 to 30 cm long.
Brush
With the brush, you will spread a very thin layer of glue on the flap and then press the parts together. The amount
The glue should be small, covering the entire surface, but not coming out of the joint after joining the parts.
You can practice with the scraps of cardstock that are left after the pieces are cut out. Please remember to rinse
your brush with warm water, otherwise the glue on the brush will dry out over time, undermining the process of
glue spread. Anyway, you can use any other method to spread the glue as you like.
Glue surface
For convenience, squeeze a little glue onto the prepared surface to make it easier to dip the glue
brush introduction. Cardboard scraps are suitable for this
Surface to cut
Prepare your table top for cutting the pieces. For this purpose, you can use a sheet of wood
plywood or cutting board. This would help you keep your table safe and sound.
Numbers
Gluing place
External side
Cardboard
Better to use colored paper. It is sold in a craft store or bookstore.
The weight of the cardstock must be at least 180.
Glue
Better use Carpenter's glue, UHU or UNIPOX glue, it is available in any store
DIY or bookstores. The most convenient way is to squeeze some glue on the
prepared surface, and then take glue from this surface with a brush, spreading it
on the lapels. Then press the pieces together and keep them under pressure for 7-10
seconds until the glue forms. Spread the glue in one layer
very thin. If you put more glue on the fin, the cardstock will get soggy, and drying
it will take too long, and when joining the parts, the glue will come out of the joint.
I strongly remind you to avoid printing on a glossy surface. Printed lines
on a shiny surface they will smudge when they come in contact with the glue.
In this way, the appearance of the model will be spoiled.
Color guide
Size
A4
High 70 Cm
Pages Pieces
ōų đºō
5 6 7 8
Copyright © 2022 Daniel Paper Art. All rights reserved
9 10 11 12
13 14 15 16
17 18 19 20
27 28 30 32
29 31
Copyright © 2022 Daniel Paper Art. All rights reserved
33 34 35 36
37 38 39 40
41 42 43 44
51 52 53 54
Copyright © 2022 Daniel Paper Art. All rights reserved
55 56 57 58
59 62 63 64
60
61
65 66 67 68
73 74 75 76
Copyright © 2022 Daniel Paper Art. All rights reserved
77 78 79 80
81 82 83 84
85 86 87 88
93 94 95 96
Copyright © 2022 Daniel Paper Art. All rights reserved
97 98 99 100
Congratulations!
EXTRA 4 EXTRA 5 EXTRA 6