Professional Documents
Culture Documents
FS N11P
FS N11P
Quick Start
Digital Fiber Sensor Fine sensitivity adjustment
Mode/Output *2
Press the [MODE] button once, then
FS-N10 Series
Up Down use to select L-on or D-on
Preset function
Instruction Manual Configure easily
with a single press
when receiving light
Setting value Light intensity
Sensitivity setting Power select switch *1
*1 This is a channel switch on 2-output types. This is not equipped with the 0-line type.
*2 Press and hold the [MODE] button to make advanced setting changes.
Read this manual before using the product in order to achieve maximum performance. SET button (SET)
Keep this manual in a safe place after reading it so that it can be used at any time. Operation status indicators
Failure to follow these instructions may lead to death or seri- PST indicator Sub screen
Danger ous injury. DTM indicator (Displayed in green)
Digital display Main screen
Warning Failure to follow these instructions may lead to injury.
Manual button (Displayed in red)
( )
Failure to follow these instructions may lead to product dam-
Caution age (product malfunction, etc.)
Expansion
protective cover
Note Provides additional information on proper operation.
Expansion connector
MODE button (MODE)
Preset button (PRESET)
This provides useful tips for the feature being described.
Cable*2 Power select switch*1
Tip
Dust cover
See "FS-N10 Series User's Manual" for details on the features of the FS-N10 Series and
detailed instructions for configuration. *1 Setting to "M" locks the power mode to MEGA mode. The switch is a channel switch for the
two output type. This is not equipped with the 0-line type.
*2 On the FS-N1 C , this is an M8 connector rather than a cable. On the FS-N1 EN, this is
an e-CON connector.
Hints on Correct Use
Mounting Unit
• This product is just intended to detect the object(s). Do not
use this product for the purpose to protect a human body or
a part of human body. Mounting on a DIN Rail 3
Warning
• This product is not intended for use as explosion-proof
product. Do not use this product in a hazardous location
1 Align the claw at the bottom of the main body with
the DIN rail, as shown in figure1.
and/or potentially explosive atmosphere.
While pushing the main body in the direction of
• This product uses DC power. Do not apply AC power. The 2
product may explode or burn if an AC voltage is applied. the arrow 1, push down in the direction of arrow 2. 1
Included accessories
• Instruction Manual 1pc.
1
.
Note • If a thin fiber unit is used, an adapter provided with the thin fiber unit will be
Other Calibration Methods
required.
Unless the correct adapter is connected, the thin fiber unit will be loose and
not detect targets correctly (the adapter is supplied with the fiber unit).
Increased Resistance to Dust and Dirt
Cable outer dia Adapter Appearance
z Maximum Sensitivity Calibration
In the state shown below, press and hold the [SET] button for three seconds or more. Stop
Adapter A pushing when "5'6" flashes.
φ1.3 (OP-26500) The sensitivity is set slightly higher than the received light intensity.
Workpiece
3 Slide the main unit and expansion unit(s) together.
Engage the two claws of the expansion unit with Settings complete
the recesses on the main unit side until you hear/
feel a click. Position Workpiece
z Positioning Calibration
4 Attach the end units (option: OP-26751) to the DIN
Press the [SET] button with no workpiece.
rail in the same way as step (2).
Place the workpiece in the location you wish to position it. Press and hold the [SET] button
5 Secure the amplifiers between the end units. for at least 3 seconds. Release the button when "5'6" flashes.
Tighten the screws at the top (two screws x two Common to
units) with a Phillips screwdriver to fix the end Thrubeam and Reflective Models Press [SET] button once with
units. no workpiece
Calibration Method
Detecting Even Small Differences Press and hold [SET] button with
workpiece
z Two-point Calibration
Two-point calibration is the basic method of calibration.
Press the [SET] button once without the workpiece, and then press it once again with the
workpiece.
Press and hold until
1 Press the [SET] button with no workpiece.
Workpiece
"UGV" flashes
[SET] will be displayed on the sub-menu (green display).
Settings complete
You can disable various Preset functions by pressing and holding the [PRESET]
If "----" flashes for two seconds on the main screen, the light intensity is too small between button.
Tip
conditions when the workpiece is absent and when it is present. These values will be set,
but there is the possibility that detection may become unstable.
2
z Preset Function z Full Auto Preset Function
This function adjusts the current value to "". This function automatically differentiates between two conditions (presence/absence of
With light received, press the [PRESET] button. The current value is set to "". workpiece) and adjusts the current values to "" and "". This is effective for cases when
the workpiece is moving at high-speed.
Press [PRESET] button once Press and hold the [PRESET] button with no workpiece in place. While "#WVQ" is flashing,
with no workpiece pass a workpiece through. (Continue pressing the [PRESET] button while the workpiece
passes through.)
Common ・
to Thrubeam and Reflective Models
Pressing the [PRESET] button and the button at the same time will set the current Set Current Value to "0"
value at that time to "". Values that have been set to "" with the Preset function cannot
be changed. z The Zero Shift Function
This function is primarily used with reflective models.
100.0 Press the [PRESET] button and button at the same time.
Workpiece
3.0
.0
[PRESET] +
Green "PST"
lights up • The current value is set to "".
• Green "PST" lights up
Note The zero shift and preset function cannot be used together. To use the
preset function, you must first disable the zero shift function.
z Maximum Sensitivity Preset Function Adjusting the current intensity value when it is too large
This function sets conditions that will serve as reference, to "" and adjusts conditions with (when saturated).
slightly high light intensity as "". This is useful when you would like to perform detection
using the background as a reference with reflective models.
In the following conditions, press and hold the [PRESET] button for 3 seconds or more then
z Use the Saturation Recovery Function
release your finger when "#WVQ" is flashed. Press the [SET] button while pressing the [MODE] button.
Workpiece
Press and hold for 3 seconds or more Press the [SET] button while
pressing the [MODE] button.
After adjusting the light transmission level and light intensity sensitivity, the current values
Reflective model : without workpiece will be adjusted to within the ranges listed in the table that follows.
Power mode Light intensity setting range
HSP*, FINE, TURBO 2047 ± 350
SUPER 4095 ± 500
ULTRA, MEGA 5000 ± 600
Press and hold for 3 seconds or more
*HIGH SPEED
• The maximum value for the light intensity while the [PRESET] button is being pressed is z Disable Saturation Recovery
set to ", and light-intensity that is slightly higher than the maximum value at that time
will be adjusted to "". When the saturation recovery function is enabled, press the [SET] button while pressing the
• The setting value is "" [MODE] button to cancel it.
• The green [PST] indicator will light up.
Note Cannot be executed when the Preset function is already being used (when Handy Uses for the Saturation Recovery Function
the [PST] indicator is flashing). Press and hold the [PRESET] button to dis- This function is useful when the intensity value is saturated after installation.
able the Preset function before executing this function. This function corrects the saturation via a simple operation, by automatically
Tip
calibrating the light transmission level and light intensity gain.
3
Output Switch Initializing the Settings
Either light-ON (L-on) mode or dark-ON (D-on) mode can be selected. Initialization Method
1 While the current value is displayed, press the [MODE] button once.
1 Press and hold the [SET] and [PRESET] buttons simultaneously for three seconds.
2 Use to switch the output (.QP/&QP), then press the [MODE] button again.
The output change completes, and the display returns to the current value. Press and hold for 3 seconds or more
Connecting to External Devices 2 Use the to select "456", then press the [MODE] button.
Cable Types After initialization is complete, the display returns to the current value.
Load
PLC, etc.
protection circuit
(Short-circuit
Power mode FINE
protection circuit
current 2 mA
Overcurrent
Black or less)
Black (Control output 1)
(Control output 1)
White Detection mode Std (Normal)
*2
White (Control
DC3.3V (Control output 2) output 2)*2 Load Setting value 50
Load
PLC, etc. (Short-circuit Output switch L-on
Pink*2 current 1 mA Pink*2
or less)
*1 0V *1 0V
Blue Blue
Protection
10 kΩ or more
Overcurrent
Black
Load swift motion to cut the fiber. 2
(Control output)
Blue
0V
Fiber Fiber cutter
(OP-87098)
PLC, etc.
(Short-circuit
protection circuit
protection circuit
Sensor main circuit
Overcurrent
current 2 mA
or less)
(Control output)
(Control output 1) • The fiber cutter comes with the fiber unit.
(Control
DC3.3V output 2)*2 Failure to follow the cautions below could reduce the detection range.
Load
Load
FS-N11CN/N12CN 2 4
OP-73864
(Cable length: 2 m)
Connected
pin No. Wire color 6WT$ TURBO mode
OP-73865
3
4 2
1
1
2
Brown
White
5W24 SUPER mode
Error Displays and Corrective Actions 5'6 5VF Normal sensitivity setting method
Check the load and return the current 5'6 15'V Zero-shift calibration
ErC Overcurrent in the control output.
within the rated value.
ErE Failed to write/load the internal data. Perform initialization (p.4). '0& MODE
Settings complete
5V) &K52
detection is required.
Go to display setup mode
For disabling (setting) method, see
Loc The keylock function is ON.
"FS-N10 Series User's Manual". 5V) 5;5 Go to system setup mode
Consult your nearest KEYENCE office regarding error displays other than the ones listed above. Return to normal display
MODE
*1 You can press the button to set between the range of 2 to 2.
4
Detection Settings System Settings
1
On-delay timer *
Eco feature off
One-shot timer *1
Enable eco feature
Normal (light intensity) Reduce power consumption
detection mode (response time 4 times slower)
DATUM1 mode *2
Standard current value display
DATUM2 mode *2
Maximum current value display
Area detection mode (4 times hysteresis)
Display Settings
Return to normal display
MODE
*1 Press the button to set between the range of and (ms).
Normal display method *2 Only 2 output types (FS-N13N/N13P/N14N/N14P/N13CP/N14CP).
Reverse display
Sub-display off
Extended display
Bar display
Settings complete
5
Specifications