Professional Documents
Culture Documents
tools needed
2
table of contents
introduction 2
hardware 4
parts list 5
safety precautions 6
helpful hints 7
installing L-bracket 8
assembly 9-17
QUESTIONS? Just call 1-800-874-0008 for parts and service. For faster service, have the style number and DPCI number ready when calling. 3
hardware
4
ITEM DESCRIPTION QUANTITY
A side panel 2
B top/bottom panel 2
C horizontal divider 2 E
D vertical divider 9
E back panel 6 E B
D
E
D
E D E
A
E
C D
D
D
A
C
D
D
D
5
safety precautions
warning
• This unit contains small parts which could be a choking hazard for small children. Children should be under adult supervision at all times or
serious injury could occur.
• Always unload unit prior to moving the unit. The weight of personal belongings can cause the unit to become unstable and either tip or collapse.
Serious bodily injury and/or damage to personal belongings may occur.
• Do not overload unit. If any shelf, top, or bottom of unit bows or bends, it is overloaded. The shelf, top, or bottom could collapse and cause
serious bodily injury and/or damage to personal belongings.
• Do not climb or step on the unit. This is not a bench. The unit may become unstable and either tip or collapse. Serious bodily injury and/or
damage to personal belongings may occur.
• Do not use this unit as a television stand. Serious bodily injury and/or damage to personal belongings may occur.
• Do not mount or attach anything to the sides, rear or front of the unit as this can create a force which can cause the unit to tip. Serious bodily
injury and/or damage to personal belongings may occur.
• Do not stack units in a vertical format. Stacking of units can cause an unsafe tip-over hazard which may cause serious bodily injury and/or
damage to personal belongings.
• Do not hang this unit on the wall. The product structure is not designed for wall hanging. Serious bodily injury, damage to personal belongings,
and/or damage to the wall may occur.
• All units must be secured individually to wall stud using L-Bracket and Wall Screw (#10 x 1-1/2 in.) provided. If wall stud is not accessible,
consult your local hardware store for appropriate mounting hardware. Failure to do so may create an unsafe tipping hazard that could lead to
serious bodily injury and/or damage to personal belongings.
• We recommend you protect your work surface during assembly to prevent scratching or damage to table tops, wood floors, etc.
6
helpful hints
We recommend you protect your work surface during assembly to prevent scratching or damage to table tops, wood floors, etc.
Unfinished edges are shaded in gray. It is important to understand how finished edges go together. Take a moment to lay out all
the wood pieces and note the finished and unfinished (raw wood) edges. Arrange pieces so all finished edges are facing the same
way. While assembling, take care to note in each diagram which way finished edges are facing. In general, all finished edges will
face forward and all finished sides (large area of piece) will face up when product is fully assembled and upright.
7
installing L-bracket
long wall
end stud
Min.
1/2 in.
Max.
WARNING 1 in.
Serious or fatal crushing injuries can occur
from furniture tip-over. top panel Do not install this unit flush against the
To help prevent tip-over:
wall! This unit requires a gap of between
- Install tip-over restraint provided.
- Unless specifically designed to
1/2 inch and 1 inch to install properly.
accommodate, do not set TVs or other
heavy objects on top of this product.
- Never allow children to climb or hang on
drawers, doors, or shelves.
- Place heavy items on lower shelves and as
far back as possible. wall For more hidden hardware, secure L-bracket
stud under top panel. See step 8 for detailed
Use of tip-over restraints may only reduce,
but not eliminate, the risk of tip-over. installation instructions.
This is a permanent label. Do not attempt to remove.
8
step 1.
D
D
D
D
D
D
(H1) x 6
long dowel
9
step 2.
(H1) x 6
long dowel
10
step 3.
D
D
C D
11
step 4.
(H2) x 12
short dowel
1. Push twelve short dowels (H2) into top/bottom panels as shown. Top/bottom panels are the same.
12
step 5.
(H4) x 6
assembly screw
#5mm x 38mm
13
step 6.
(H4) x 16 (H3) x 22
assembly screw screw cover
#5mm x 38mm
1. Attach side panels to assembly using eight screws (H4) through each side panel as shown.
2. Push screw covers (H3) onto all screw heads.
14
step 7.
E
E
E
(H5) x 72
nail
15
step 8.
wall
stud
top panel
top panel
wall
stud
(H6) x 1 (H7) x 1 (H8) x 1
L-bracket L-bracket screw wall screw
#10 x 1/2 in. flathead #10 x 1-1/2 in.
1. Align unit with wall stud and refer to page 8 for installation instructions.
2. Place short end of L-bracket (H6) against wall/wall stud. Uses 1-1/2 in. screw (H8) to secure L-bracket to wall stud.
3. Use 1/2 in. screw (H7) to secure L-bracket to top panel (B).
16
step 9.
or
or
single unit
when
stacking units
(H2) x 2 (H9) x 2
short dowel hole plug
1. For single unit: Insert hole plugs (H9) into top holes. For stacking units: insert dowels (H2) into top holes.
17
weight capacity/care instructions
50 lbs. warning
This unit has been designed for the weight
shown. Exceeding this recommended weight
could result in excessive "sagging" of the top
or shelves. Extreme overloading can cause
failure of the unit and possible injury.
15 lbs.
15 lbs. Care Instructions:
15 lbs. Dust with a clean, lint-free dry cloth.
50 lbs.
15 lbs.
15 lbs.
15 lbs.
15 lbs.
15 lbs.
15 lbs.
15 lbs.
15 lbs. 15 lbs.
15 lbs.
15 lbs. 15 lbs.
15 lbs.
15 lbs.
15 lbs.
15 lbs. 15 lbs.
15 lbs. 15 lbs.
15 lbs. 15 lbs.
18
19
© 2018 Target. The Bullseye Design is a trademark of Target Brands, Inc. All rights reserved.