Professional Documents
Culture Documents
PR-88H User's Manual
PR-88H User's Manual
AC power cable
B
US
USB Cable
AC Adapter
01
Chapter 2 Specification Chapter 3 Product Overview
3.1 Printer Parts
Printing Method Thermal line printing
Printing Speed Max 250 mm/sec
Resolution 203 DPI 2
1
Paper Supply Mode Easy paper loading
1. Cover Opener
Language User language supported 2. Printer Cover
Interface RS-232 / USB / Ethernet 3 3. Paper Cabin
5
Pringing width 72 mm 4. Cutter Cover
5. Printer Head
Printing Font A:12×24 4
6. Control Panel
Character Size
Font B:9×17 6 7. Power Button
Character Per Line Font A:48
7
Font B:64
Barcodes Code 39,Code 128,EAN 8,EAN 13
Driver Windows 2000/XP/2003 Server/VISTA/7
Sensor Out of paper
3.1
Receive Buffer Size 4K Bytes
Mass Approx.1.45 kg
3.2 Interfaces
Dimensions W×D×H 146×196×152mm
Paper type Thermal Paper
Paper Width 79.5±0.5 mm
Diameter Max.¢80 mm
Printer head life Approx. 100 km (pringting rate 12.5% or less) 8. Power Plug Port
Reliability 9. Cash Drawer Interface
Autocutter 500,000 cuts
10. Ethernet Port
Power supply 24 VDC ± 10%
Usage 11. USB Port
Operating 5℃~45℃,20~85%RH 12. RS232 Interface
conditions 8
Storage -10℃~50℃,10~90%RH(the paper is not included) 12
Notice: The printing speed relates with data transporting, command control
and power voltage etc.
9 10 11
3.2
02 03
Chapter 4 Usage Description 4.3 Install the Roll Paper
4.1 Connection the Cables 1. Make sure that the printer is not receiving data before replacing the roll paper;
otherwise, data may be lost.
2. Upward the” PULL” buckle handle till the cover open.
3. Remove the used paper roll core.
4. Put into new paper roll. As picture 4.4shows.
5. Be sure the correct direction of the paper comes off the roll.
6. Pull out a small amount of paper, and then close the cover. As picture 4.5shows.
4.1
POWER
4.3 4.4
ERROR
FEED
Paper end direction:
4.2
04 05
4.4 Installing Oil Proof Cover
The printer is an Oil Proof Cover supplied. It’s used to prevent water
splashing into the inside of the printer and not oil-water corrosion and
oxidation protection to the internal electronic components, which
extends the life of the printer.
Installation method:
Put the Oil Proof Cover onto the printer cover as the picture4.7 shows.
4.9
4.7
4.5 Paper Jam Caused By Cutter 4.6 Self-Test and DUMP Mode
1. If the paper is thick or sudden lack of power when cutting, paper jam might 1. Press "FEED" button and hold on when powering on the printer, the
appear.(cutter cannot reset) printer will perform self-test.
2. Normally the cutter will reset when repowered, if the cutter did not reset, 2. Power off the printer and take out the paper roll. Then press "FEED"
users could follow below steps to solve the problem.
button and hold on and power on the printer. Then put in the paper
① Take away the cutter cover as below picture4.8 shows.
roll and close the printer cover. The printer will print out "DUMP".
② Stir the cutter gear till the cutter moves to the Initial position as picture4.9
shows. That means the printer enters in DUMP mode. All data will be printed
out in raw hex format.
Back to normal mode: restart the printer could put the printer in normal
mode.
4.8
06 07
4.7 DIP Switch DIP switches could perform printer configurations as follows: COM port baud
rate adjusting, beep alarm switch, printing density adjusting, parity selection
1)Unscrew the screw on bottom of printer and take away the metal cover as (for serial communication), parallel printing server mode or normal mode
the picture 4.10shows. adjusting , EPSON mode or 64character mode switching, Chinese Character
2)Users will find the DIP switches under the window as the picture 4.11shows. double byte mode or English character single byte mode selection.
Below are lists of DIP configurations:
9600bps ON ON ▲
19200bps ON OFF
38400bps OFF ON
4.10
Beep DIP3 Default Density DIP4 Default
ON ON ▲ l ight ON ▲
ON ON No parity - - ▲
6
ON OFF No parity - -
5
4
E4
6
OFF ON Odd - -
3
JA
8
7
ON 6
5
4
3
2
1
08 09
4.8 Interface Explanation 4.8.3 Ethernet Interface
PRINTER HOST
SIDE SIDE
(TXD) 2 3 (RXD)
(RXD) 3 2 (TXD)
Pin No. Signal Name Description
(GND) 5 5 (GND)
(DTR) 6 6 (DSR) 1 TX+ Tranceive Data+
(RTS) 8 8 (CTS)
2 TX- Tranceive Data+
3 RX+ Receive Data+
Printer serial port is DB9, baud rate supports 9600, 19200, 38400, 115200 bps, 4 n/c Not connected
8 bits data word length, 1 stop bit, no parity settings. 5 n/c Not connected
6 RX- Receive Data-
Descriptions to interface signals:
7 n/c Not connected
Pin No. Signal name Direction Function 8 nc Not connected
1 - - -
2 TXD Output Transmit Data
4.8.4 Drawer Connector Interface
3 RXD Intput Receive Data
4 - - -
5 GND - Signal Ground
6 DTR Intput Ready To Sen
6 1
7 - -
8 RTS Output Clear To send
10 11