Professional Documents
Culture Documents
Catalogo de Lamot CDC
Catalogo de Lamot CDC
Quality
Quality begins during our first contact with you. That quality is an integral part of every step we take to provide you with
what you expect to receive. All manufacturing is performed under an approved ISO 9001 Quality Assurance System
which ensures that rupture discs and holders are built to exacting specifications. LaMOT Disc Products can supply
rupture discs certified to the standards of ASME, the European Pressure Equipment Directive, 3A Sanitary Standards
Council and many others.
Service
A commitment to supply the services you expect
• Technical assistance, training and support
• Fast, technical, easily understood quotes
• Providing product to your specifications
• Shipping schedules that are unmatched in the industry
PAGE 2
TABLE OF CONTENTS
RUPTURE DISCS
COMPOSITE
30° Angular Seat LD 7
30° Angular Seat LDV 7
30° Angular Seat LPL 8
30° Angular Seat LPLV 8
Flat Seat LDV-G 9
Isolation Seal 9
STANDARD
30° Angular 10
Flat Seat 10
RUPTURE DISCS
HOLDERS INSERT 16
FULL BOLTED 16
UNION 16
SCREW TYPE 17
THROWAWAY 17
PAGE 3
RUPTURE DISC SELECTION TREE
Determine Rupture Pressure (RP)
Calculated Operating OP
80% 70%
Ratio Required RP
Non-Fragmenting Fragmenting
DETAILED
Design Design
• LD • Standard
• LDV
• LPL
• LPLV
• LDV-G
Additional Considerations:
• Gas or Liquid Service
• Primary/Secondary/Relief Valve
• Material Requirements (Corrosion & Temperature)
• Other factors may apply when choosing a rupture disc
PAGE 4
RUPTURE DISC SELECTION TABLE
PRESSURE RATIO
MAX. OPERATING
STANDARD MATERIALS
WITHSTAND FULL
RECOMMENDED
BURST
PRESSURE
TO BURST
VACUUM
ALUMINUM
RANGE
HASTELLOY
RUPUTURE PROCESS MANUFACTURING
SIZE
INCONEL®
DISC ENVIRONMENT PSIG
MONEL®
RANGE
NICKEL
(SIZE &
TYPE
316 SS
MATERIAL
DEPENDANT)
®C
Gas or Liquid Standard,
Composite LD (static, cyclic or pulsating) 1-12” 2-1,440 80% 3/4, 1/2, 1/4, Zero
Composite Gas or Liquid Standard,
LDV (static, cyclic or pulsating) 11/16- 12” 4-1,440 80% 3/4, 1/2, 1/4, Zero
Composite Gas or Liquid Standard,
LPL (static, cyclic or pulsating) 1-12” 4-1,440 80% 3/4, 1/2, 1/4, Zero
Composite Gas or Liquid Standard,
LPLV (static, cyclic or pulsating) 1-12” 8-1,440 80% 3/4, 1/2, 1/4, Zero
Composite Gas or Liquid Standard,
LDV-G (static, cyclic or pulsating) 11/16” 30-760 80% 3/4, 1/2, 1/4, Zero
Composite Gas or Liquid
Isolation Seal (static, cyclic or pulsating) 2-12” 3-40 50% Min/Max
Standard 30° Gas or Liquid Standard,
Angular Seat
1/2-12” 3-6,000 70% 3/4, 1/2
Gas or Liquid Standard,
Standard- V (static, cyclic or pulsating) 1-12” 4-6,000 70% 3/4, 1/2
Standard Flat 1/2”,
Gas or Liquid Standard,
Seat (static, cyclic or pulsating) 11/16”, 47-15,550 70% 3/4, 1/2
3/4”
Composite LD
Composite LDV
Composite LPL
Composite
LPLV
Composite
LDV-G
Composite
Isolation Seal
Standard 30°
Angular
Standard 30°
with Vacuum
Support
STD-V
Standard Flat
Seat
PAGE 5
COMPOSITE RUPTURE DISCS
The Composite Rupture Disc is constructed of two or more components of metallic and/
or non-metallic materials. It is a differential pressure relief device used for protecting
equipment, vessels and systems from an overpressure condition. The Composite Rupture
Disc is an ideal choice for primary and/or secondary system relief protection and the non-
fragmenting design provides an effective means of fugitive emission control when used
to isolate a safety relief valve.
Vacuum Support
Seal
(Optional)
Slot Cover
Top Section
Protective Ring
(Optional)
PAGE 6
COMPOSITE RUPTURE DISCS
The LD is the basic Composite Rupture Disc and consists The LDV Rupture Disc is a type of LD Rupture Disc with
of a slotted metal top section, with a fluoropolymer or a vacuum support installed on the process side of the
metallic seal on the process side. rupture disc.
Materials Aluminium, MONEL®, Nickel, INCONEL®, Materials Aluminium, MONEL®, Nickel, INCONEL®,
316 SS, HASTELLOY®C 316 SS, HASTELLOY®C
Seat Configuration 30° angular Seat Configuration 30° angular
Holders • Insert Holders • Insert
• Full Bolted • Full Bolted
• Union • Union
Compatible with BDI-FLX® or B.D.I.® Compatible with BDI-FLX® or B.D.I.®
Alarm System Alarm System
Tagging Three dimensional stainless steel flow Tagging Three dimensional stainless steel flow
direction tag attached to all sizes direction tag attached to all sizes
PAGE 7
COMPOSITE RUPTURE DISCS
The LPL Rupture Disc incorporates a fluoropolymer outlet The LPLV Rupture Disc is like the LPL Rupture Disc, but
liner and process side seal for added protection against additionally will withstand full vacuum. It is usually
corrosion or product build up. This rupture disc typically constructed of a fluoropolymer outlet liner, metallic
consists of a fluoropolymer outlet liner, metallic top section vacuum support, metallic top section and fluoropolymer
and fluoropolmer seal on the process side. seal on the process side. Positioning fluoropolymer material
on both the inlet and outlet sides helps protect the vacuum
support and top section from corrosive media and reduces
product build up.
Size 1" - 12" (25mm - 300mm) Size 1" - 12" (25mm - 300mm)
Burst Pressure Range 4 - 1440 psig (0,276 - 99,3 barg) Burst Pressure Range 8 - 1440 psig (0,552 - 99,3 barg)
(Size & Material Dependant) (Size & Material Dependant)
Maximum 80% Maximum 80%
Recommended Recommended
Operating Ratio Operating Ratio
Available Maximum 1000° F (538° C) Available Maximum 1000° F (538° C)
Temp Limit Temp Limit
Service Gas or Liquid Service Gas or Liquid
Non-Fragmenting Yes Non-Fragmenting Yes
Design Design
Withstand Full Yes, with a support Withstand Full Yes
Vacuum Vacuum
Operating Static, Cyclic or Pulsating Operating Static, Cyclic or Pulsating
Conditions Conditions
Materials Aluminium, MONEL®, Nickel, INCONEL®, Materials Aluminium, MONEL®, Nickel, INCONEL®,
316 SS, HASTELLOY®C 316 SS, HASTELLOY®C
Seat Configuration 30° angular Seat Configuration 30° angular
Holders • Insert Holders • Insert
• Full Bolted • Full Bolted
• Union • Union
Compatible with BDI-FLX® or B.D.I.® Compatible with BDI-FLX® or B.D.I.®
Alarm System Alarm System
Tagging Three dimensional stainless steel flow Tagging Three dimensional stainless steel flow
direction tag attached to all sizes direction tag attached to all sizes
PAGE 8
COMPOSITE RUPTURE DISCS
PAGE 9
STANDARD RUPTURE DISCS
Size 1" - 12" (25mm - 300mm) Size 1/2” and 11/16” (12 mm and 17 mm)
Burst Pressure Range 3 - 6000 psig (0,207- 414 barg) Burst Pressure Range 47 - 15,500 psig (3,24 - 1068 barg)
(Size & Material Dependant) (Size & Material Dependant)
Materials Aluminium, MONEL®, Nickel, INCONEL®, Materials Aluminium, MONEL®, Nickel, INCONEL®,
316 SS, HASTELLOY®C 316 SS, HASTELLOY®C
Seat Configuration 30° angular Seat Configuration Flat
Holders • Insert Holders • Screw Type
• Full Bolted • Throwaway
• Union
Compatible with BDI-FLX® or B.D.I.® Compatible with No
Alarm System Alarm System
Tagging Three dimensional stainless steel flow Tagging Unattached wire-on tag
direction tag attached to all sizes
PAGE 10
STANDARD RUPTURE DISCS
The LaMOT Brand Standard Rupture Disc is available in a 30° angular “Light-Lip” seat and a 30° angular “Heavy-Lip”
seat. Size and rupture disc holder bolting class determine the seat design. Refer to the table below for information on
application of Heavy-Lip seating. Seating not indicated in the table as Heavy-Lip, will be Light-Lip.
PAGE 11
BURST PRESSURES FOR COMPOSITE RUPTURE DISCS
Rupture Minimum Pressure for Preformed Composite Rupture Discs with a Fluoropolymer Seal (psig/barg)
Disc
Nominal LD LDV LPL LPVL
Size
TFE FEP, PFA TFE FEP, PFA TFE FEP, PFA TFE FEP, PFA
1 in 25 30 30 35 35 40 60 80
25 mm 1,73 2,07 2,07 2,42 2,42 2,76 4,14 5,52
1 ½ in 22 27 25 34 32 38 60 75
40 mm 1,52 1,87 1,73 2,35 2,21 2,63 4,14 5,18
2 in 7 15 10 18 15 20 28 35
50 mm 0,483 1,04 0,690 1,25 1,04 1,38 1,94 2,42
3 in 6 8 8 11 11 16 18 25
80 mm) 0,414 0,552 0,552 0,759 0,759 1,11 1,25 1,73
4 in 5 7 7 8 6 9 15 18
100 mm 0,345 0,483 0,483 0,552 0,414 0,621 1,04 1,25
6 in 3 4 5 7 5 7 12 14
150 mm 0,207 0,276 0,345 0,483 0,345 0,483 0,828 0,966
8 in 2 3 5 5 4 5 11 11
200 mm 0,138 0,207 0,345 0,345 0,276 0,345 0,759 0,759
10 in - 3 - 5 - 5 - 8
250 mm - 0,207 - 0,345 - 0,345 - 0,552
12 in - 2 - 4 - 5 - 8
300 mm - 0,138 - 0,276 - 0,345 - 0,552
Pressures stated are based upon the minimum and maximum of the manufacturing range at 72°F (22°C).
For information concerning conditions or size not shown, consult the factory.
PAGE 12
BURST PRESSURES FOR STANDARD RUPTURE DISCS
Rupture Protective Ring: When Burst Pressure is Less Than Value Stated
Min-Max Burst Pressure (psig/barg)
Disc Below, A Protective Ring is Recommended
Nominal HASTELLOY® Aluminum HASTELLOY®
Size Aluminum MONEL® Nickel INCONEL® 316 SS MONEL® Nickel INCONEL® 316 SS
C C
½ in 65-1,500 350-6,000 300-6,000 560-6,000 760-6,000 760-6,000 520 3,000 2,290 3,600 3,700 5,300
13 mm 4,48-103 24,1-414 20,7-414 38,6-414 52,4-414 52,4-414 35,9 207 158 248 255 -
1 in 29-1,000 180-6,000 150-6,000 250-6,000 420-6,000 420-6,000 260 1,500 1,145 1,800 1,830 2,670
25 mm 2,00-68,9 12,4-414 10,3-414 17,2-414 29,0-414 29,0-414 18,0 103 78,9 124 126 -
1 ½ in 22-750 116-6,000 100-6,000 150-6,000 275-6,000 275-6,000 180 1,030 790 1,240 1,255 1,780
40 mm 1,52-51,7 8,00-414 6,90-414 10,3-414 19,0-414 19,0-414 12,4 71,0 54,4 85,5 86,5 -
2 in 13-570 70-4,500 60-4,000 110-6,000 150-6,000 150-6,000 110 635 485 760 775 1,300
0,896-
50 mm 39,3 4,83-310 4,14-276 7,58-414 10,3-414 10,3-414 7,58 43,8 33,4 52,4 53,4 -
3 in 10-460 50-3,200 45-2,500 80-4,000 117-6,000 117-6,000 75 445 340 535 545 890
80 mm 0,690-31,7 3,45-221 3,10-172 5,52-276 8,07-414 8,07-414 5,17 30,7 23,4 36,9 37,6 -
4 in 7-360 40-2,400 35-1,900 70-3,000 90-6,000 90-3,600 60 350 270 420 430 670
0,483-
100 mm 24,8 2,76-165 2,41-131 4,83-207 6,21-414 6,21-248 4,14 24,1 18,6 29,0 29,6 -
6 in 5-275 30-1,800 25-1,400 472,200 62-3,600 62-3,600 45 260 200 315 320 445
150 mm 0,345-19,0 2,07-124 1,72-96,5 3,24-152 4,27-248 4,27-248 3,10 17,9 13,8 21,7 22,1 -
8 in 4-205 23-1,450 20-1,100 34-1,700 51-2,100 51-2,100 35 200 155 240 245 330
200 mm 0,276-14,1 1,59-100 1,38-75,8 2,34-117 3,52-145 3,52-145 2,41 13,8 10,7 16,5 16,9 -
10 in 4-165 17-1,150 16-800 30-1,400 43-1,400 43-1,400 28 160 125 195 200 270
250 mm 0,276-11,4 1,17-79,3 1,10-55,2 2,07-96,5 2,96-96,5 2,96-96,5 1,93 11,0 8,62 13,4 13,8 -
12 in 13-670
3-140 15-960 25-1,000 36-1,000 36-1,000 24 135 105 160 165 220
0,900-
300 mm 0,207-9,65 1,03-66,2 46,2 2,14-68,9 2,48-68,9 2,48-68,9 1,65 9,31 7,24 11,0 11,4 -
Rupture Min Burst Pressure with a Fluoropolymer Liner Maximum Burst Pressure
Disc Add to Burst Pressure (psig/barg) With Fluoropolymer Liners(psig/barg)
Nominal HASTELLOY®
Size Inlet or Outlet Only Both Inlet & Outlet Aluminum MONEL® Nickel INCONEL® 316 SS C
¼ in - - - - - - - -
6 mm - - - - - - - -
½ in 150 300 1,500 6,000 6,000 6,000 6,000 6,000
13 mm 10,3 20,7 103 414 414 414 414 414
1 in 50 100 1,000 3,000 3,000 5,000 5,000 5,000
25 mm 3,45 6,90 68,9 207 207 345 345 345
1 ½ in 35 70 700 2,000 2,000 3,400 3,400 3,400
40 mm 2,41 4,83 48,3 138 138 234 234 234
2 in 25 50 500 1,300 1,300 1,800 1,800 1,800
50 mm 1,72 3,45 34,5 89,6 89,6 124 124 124
3 in 15 30 400 900 900 1,500 1,500 1,500
80 mm 1,03 20,7 27,6 62,1 62,1 103 103 103
4 in 11 22 325 650 650 1,100 1,100 1,100
100 mm 0,759 1,52 22,4 44,8 44,8 75,8 75,8 75,8
6 in 8 16 240 500 500 800 800 800
150 mm 0,552 1,10 16,5 34,5 34,5 55,2 55,2 55,2
8 in 6 12 180 375 375 600 600 600
200 mm 0,414 0,827 12,4 25,9 25,9 41,4 41,4 41,4
10 in 5 10 135 300 300 500 500 500
250 mm 0,345 0,690 9,31 20,7 20,7 34,5 34,5 34,5
12 in 4 8 110 250 250 400 400 400
300 mm 0,276 0,552 7,58 17,2 17,2 27,6 27,6 27,6
PAGE 13
RUPTURE DISC OPTIONS
PROTECTIVE RINGS
Protective rings may be used on rupture discs made of thinner materials or in instances
where delicate liners are used. These rings protect the rupture disc from foreign material
in the seating area. Protective rings also enable easier handling of rupture discs during
installation.
GASKETS
Gaskets may be used on the process side of the rupture disc to enhance sealing where
scratches or pits have occurred in the seating area of the holder. A gasket lines the seating
area of the rupture disc, improving sealing capability, provided the holder has been properly
cleaned according to product installation instructions.
VACUUM SUPPORTS
Due to the thinness of some rupture disc materials, it is necessary to support a rupture
disc when a system vacuum occurs. Vacuum supports are available that will withstand
a full system vacuum, eliminating damage to the rupture disc and ensuring proper
operation. For backpressure conditions higher than 14.7 psig (1,01 barg), consult your local
representative or the factory. When ordering a Standard or Composite rupture disc that will
be subjected to a vacuum condition, clearly specify the exact conditions that the rupture
disc will encounter. Vacuum supports will be supplied when specified. Vacuum supports
are manufactured to mate with a specific rupture disc and are permanently attached to
ensure proper installation.
PAGE 14
ALARM SYSTEMS
Continental Disc Corporation provides two systems for monitoring the burst of a rupture disc, the BDI-FLX® Sensor
System and the B.D.I.® Alarm System. Common features include:
PAGE 15
RUPTURE DISCS HOLDERS
LaMOT Brand rupture disc holders are offered in a variety of types and styles to meet customers’ needs. The basic
holder is two pieces, consisting of an inlet and an outlet.
The seating surface of each piece is machined to grip a specific type rupture disc and when assembled together with the
rupture disc, forms a gasket seal. Both the 30° seat and flat seat design are machined to industry standards. Corrosion
resistance can be enhanced by utlization of fluoropolymer coating of the holder inlet and/or outlet.
UNION HOLDERS
The Union Type Holder is designed to provide flexibility of use
in tight piping configurations. These precisely built holders
combine remarkable ease of installation with high pressure
ratings in pipe sizes of 2” (50 mm) or less. These holders are
designed to be used with either Standard or Composite (UL)
Rupture Discs. Standard sizes. Any combination of welded
or threaded connections is available. All parts are available
in Carbon Steel and 316 SS The units are designed with 30° angular seating. Identification of size, pressure rating and
flow direction is laser marked on the assembly.
If the unit has a threaded outlet, it can be supplied with a muffled plug. This reduces reaction forces upon disc rupture,
and redirects fragments or product from dispersing directly from the nozzle. For more information on the muffled plug,
contact the factory.
The Wing Nut/Hammer Nut Union Holder is supplied with extra heavy hammer lugs. This design is a favorite of field
personnel who must replace rupture discs in hard to reach locations.
LaMOT Wing Nut Union Holders are available in sizes 1”, 1½” and 2”. They have coarse threaded nuts and subs for
maximum strength and easy assembly.
Hex Nut Union Holders are available in sizes ½”, 1”, 1½” and 2”.
PAGE 16
RUPTURE DISCS HOLDERS
PAGE 17
ASME DIN JIS Height Weight
Nominal
Size Class Outside Dia. Class Outside Dia. Class Outside Dia. in/mm lbs/kg
in/mm mm mm
150 1.75/44,5 1.67/42 1.0/0,45
½ in 300/600 2.00/50,8 1.67/42 1.4/0,64
13 mm 900/1500 2.38/60,3 1.86/47 2.3/1,0
150 2.50/63,5 1.67/42 1.9/0,90
300/600 2.75/69,9 10/40 69,9 10/20 69,9 1.67/42 2.5/1,1
1 in 30/40 76,0 1.67/42 2.9/1,3
25 mm 64/160 82,0 2.38/60 4.9/2,2
250 82,0 2.38/60 4.9/2,2
900/1500 3.00/76,2 2.38/60 4.1/1,9
150 3.25/82,6 1.67/42 3.0/1,4
10/20 86,0 1.67/42 3.4/1,5
1 ½ in 300/600 3.63/92,2 10/40 92,2 1.67/42 4.0/1,8
900/1500 3.75/95,3 2.66/68 6.9/2,7
40 mm 30/40 97,0 1.67/42 4.5/2,0
64/160 102,0 2.66/68 8.1/3,7
250 108,0 2.66/68 10/4,5
150 4.00/101,6 10 101,6 1.67/42 3.6/1,6
30º INSERT HOLDER SPECIFICATIONS
Consult factory for availability of flange classes or sizes not listed. Gauge taps and facing options could affect the holder height and weight.
250 170,0 3.71/94 29/13
1500 6.75/171,5 3.71/94 29/13
10 156,0 1.67/42 6.0/2,7
10/16 162,0 16/20 162,0 1.67/42 7.4/3,4
25/40 168,0 30 168,0 2.15/55 12/5,4
150 6.75/171,5 1.67/42 9.1/4,1
64 173,0 3.13/79 18/8,3
4 in 300 7.00/177,8 2.15/55 13/5,9
100 mm 40 180,0 2.15/55 14/6,4
100/160 180,0 3.63/92 26/12
600 7.50/190,5 3.13/79 25/11
250 202,0 4.35/111 45/20
900 8.00/203,2 3.63/92 37/17
1500 8.13/206,5 4.35/111 47/22
10/16 217,0 10 217,0 2.06/52 16/7,2
150 8.63/219,2 2.06/52 17/7,7
25/40 223,0 2.93/74 26/12
16/20 235,0 2.06/52 22/9,7
6 in 64 247,0 3.96/101 55/25
150 mm 300 9.75/247,7 30 247,7 2.93/74 37/17
100/160 257,0 4.53/115 71/32
40 262,0 2.93/74 44/20
600 10.38/263,7 3.96/101 66/30
900 11.25/285,8 4.53/115 95/43
10 267,0 2.31/58 25/11
10/16 272,0 2.31/58 27/12
150 10.88/276,4 2.31/58 29/13
16/20 280,0 2.31/58 31/14
8 in 25 283,0 3.30/84 44/20
40 290,0 3.30/84 48/22
200 mm 30 293,0 3.30/84 50/23
300 12.00/304,8 3.30/84 58/26
64 309,0 4.50/114 83/38
40 312,0 3.30/84 63/29
600 12.50/317,5 4.50/114 91/41
10/16 327,0 2.55/65 34/15
10 330,0 2.55/65 36/16
150 13.25/336,6 2.55/65 40/18
25 340,0 4.18/106 69/31
40 352,0 4.18/106 81/37
10 in 16/20 353,0 2.55/65 49/22
250 mm 30 357,0 4.18/106 86/39
300 14.13/358,9 4.18/106 88/40
64 364,0 5.00/127 128/58
40 377,0 4.18/106 107/49
100 391,0 5.00/127 163/74
600 15.63/397,0 5.00/127 171/78
5 367,0 2.55/65 36/16
10 375,0 2.55/65 41/19
10 377,0 2.55/65 42/19
16 383,0 2.55/65 46/21
25 400,0 4.13/105 94/43
12 in 16/20 403,0 2.55/65 60/27
300 mm 150 16.00/406,4 2.55/65 62/28
40 417,0 30 417,0 4.13/105 114/52
300 16.50/419,1 4.13/105 116/53
64 424,0 5.43/138 161/73
40 431,0 4.13/105 130/59
600 17.88/454,2 5.43/138 211/96
PAGE 18
FULL BOLTED HOLDER SPECIFICATIONS
NOMINAL ASME Outside Bolt Studs Height Dimension of Full Bolted Assembly Number
SIZE Class Dia. Circle No. Diameter #1 #2 #3 #4 #5 #6 #7 #8 #9
150 3.50 2.38 4 .50 2.20 2.38 3.13 2.81 3.00 3.75 1.75 1.88 2.63
300 3.75 2.63 4 .50 2.00 2.63 3.50 2.88 3.50 4.38 1.69 1.75 2.63
1/2 in
600 3.75 2.63 4 .50 2.00 2.63 3.50 2.88 3.50 4.38 1.69 1.75 2.63
900/1500 4.75 3.25 4 .75 5.56 3.38 4.06 3.38 4.19 4.88 1.88 2.69 3.38
150 4.25 3.13 4 .50 1.94 2.78 3.56 2.75 3.59 4.38 1.13 1.97 2.75
300 4.88 3.50 4 .63 2.25 2.97 4.00 3.13 3.84 4.88 1.38 2.09 3.13
1 in
600 4.88 3.50 4 .63 2.38 3.10 4.13 3.25 3.97 5.00 1.50 2.22 3.25
900/1500 5.88 4.00 4 .88 3.00 3.59 4.75 4.13 4.72 5.88 2.38 2.97 4.13
150 5.00 3.88 4 .50 2.25 3.03 4.00 3.13 3.91 4.88 1.38 2.16 3.13
300 6.13 4.50 4 .75 2.13 2.84 4.00 3.50 4.22 5.38 1.63 2.34 3.50
1 1/2 in
600 6.13 4.50 4 .75 2.38 3.09 4.25 3.75 4.47 5.63 1.88 2.59 3.75
900/1500 7.00 4.88 4 1.00 3.13 3.66 5.13 4.63 5.66 7.13 2.50 3.00 4.50
150 6.00 4.75 4 .63 2.13 2.97 3.88 3.25 4.10 5.00 1.50 2.35 3.25
300 6.50 5.00 8 .63 2.44 3.16 4.31 3.63 4.35 5.50 1.75 2.47 3.63
2 in
600 6.50 5.00 8 .63 2.81 3.53 4.69 4.00 4.72 5.88 2.13 2.84 4.00
900/1500 8.50 6.50 8 .88 3.88 4.63 6.38 5.63 6.38 8.13 3.13 3.88 5.63
150 7.50 6.00 4 .63 2.56 3.09 4.44 3.75 4.28 5.63 1.88 2.41 3.75
300 8.25 6.63 8 .75 2.94 3.59 4.94 4.25 4.91 6.25 2.25 2.91 4.25
3 in
600 8.25 6.63 8 .75 3.19 3.85 5.19 4.63 5.28 6.63 2.63 3.28 4.63
900 9.50 7.50 8 .88 4.00 4.50 6.25 5.75 6.38 8.13 3.00 3.50 5.50
150 9.00 7.50 8 .63 2.75 3.72 4.88 4.00 4.97 6.13 1.88 2.84 4.00
300 10.00 7.88 8 .75 3.56 4.34 5.69 4.69 5.47 6.81 2.50 3.28 4.63
4 in
600 10.75 8.50 8 .88 3.88 4.50 5.97 5.63 6.38 7.72 3.13 3.75 5.22
900 11.50 9.25 8 1.13 5.00 5.38 7.38 6.50 7.13 9.13 3.50 4.50 6.25
150 11.00 9.50 8 .75 3.25 4.09 5.56 4.75 5.59 7.06 2.19 3.03 4.50
6 in 300 12.50 10.63 12 .75 3.50 4.13 6.50 5.31 5.94 7.88 2.88 3.50 5.06
600 14.00 11.50 12 1.00 4.75 6.13 7.38 6.75 8.25 9.38 3.63 5.63 4.75
150 13.50 11.75 8 .75 4.00 5.25 6.88 5.19 6.44 8.06 2.25 3.50 5.13
8 in
300 15.00 13.00 12 .88 4.25 5.38 7.00 6.25 7.25 8.88 3.25 4.75 6.00
12 in 150 19.00 17.00 12 .88 2.63 - 4.75 5.75 7.38 7.94 2.50 - 5.69
Outside Diameter
Connections Bolt Circle
Assembly Number
Inlet Outlet
2 Threaded Threaded
3 Threaded Weldneck
5 Weldneck Threaded
PAGE 19
UNION HOLDER SPECIFICATIONS
Overall Height
Weldneck
Size Rating Seat Design Hex Size
Bore #2U #3U #5U #6U
Connections
Assembly Number
Inlet Outlet HEX
Size
#6U
#6U Weldneck Weldneck
HEX
Size
Overall
Height
#2U
PAGE 20
SCREW TYPE HOLDER SPECIFICATIONS
Holder Maximum Holder Connection Dimensions Across Hex Flats Dimension
Rupture Height (A)
Pressure @ Seat Design Across Inlet
Temp Inlet Outlet Disc Size (in/mm) Inlet (B) Outlet (C)
72ºF/22°C Corners (D)
¼ MPT Muffled 11 16
” FS 2.28 / 57,9
38 MPT Muffled 11 16
” FS 2.28 / 57,9
½ MPT Muffled 11 16
” FS 2.28 / 57,9
¼ MPT ½ MPT 11 16
” FS 2.81 / 71,4
1,000 psig 400°F 38 MPT 1/2 MPT 11 16 FS 2.81 / 71,4 1¼ in 1 1 8 in 1.44 in
68,9 barg 204°C ” 31,8 mm 28,6 mm 36,6 mm
½ MPT ½ MPT 11 16
” FS 2.81 / 71,4
¼ MPT Free 11 16
” FS 2.03 / 51,6
38 MPT Free 11 16
” FS 2.19 / 55,6
½ MPT Free 11 16
” FS 2.03 / 51,6
¼ MPT Muffled 11 16
” FS 2.28 / 57,9
38 MPT Muffled 11 16
” FS 2.28 / 57,9
½ MPT Muffled 11 16
” FS 2.28 / 57,9
¼ MPT ½ MPT 11 16
” FS 2.81 / 71,4
3,000 psig 1,000°F 38 MPT ½ MPT 11 16 FS 2.81 / 71,4 1¼ in 1 1 8 in 1.44 in
207 barg 538°C ” 31,8 mm 28,6 mm 36,6 mm
½ MPT ½ MPT 11 16
” FS 2.81 / 71,4
¼ MPT Free 11 16
” FS 2.03 / 51,6
38 MPT Free 11 16
” FS 2.03 / 51,6
½ MPT Free 11 16
” FS 2.03 / 51,6
¼ MPT Muffled ½” FS 2.28 / 57,9
38 MPT Muffled ½” FS 2.28 / 57,9
½ MPT Muffled ½” FS 2.28 / 57,9
¼ MPT ½ MPT ½” FS 2.81 / 71,4
10,000 psig 1,000°F 38 MPT ½ MPT ½” FS 2.81 / 71,4 1¼ in 1 1 8 in 1.44 in
689 barg 538°C 31,8 mm 28,6 mm 36,6 mm
½ MPT ½ MPT ½” FS 2.81 / 71,4
¼ MPT Free ½” FS 2.03 / 51,6
38 MPT Free ½” FS 2.03 / 51,6
½ MPT Free ½” FS 2.03 / 51,6
¼ MPT ½ MPT ½” HF 2.81 / 71,4
D D D
C C C
Outlet Outlet
Outlet
Holddown
Ring Holddown Holddown
B Ring B Ring
B
Inlet Inlet Inlet
A
A A
PAGE 21
THROWAWAY HOLDER SPECIFICATIONS
Holder Connection Unit Weight Overall Height (A) Dimension Across Hex Flats Dimension
Across Inlet Corners (D)
D D D
Outlet C
C
Outlet Outlet
Holddown
Ring
B Holddown Holddown
Ring B Ring
Inlet B
Inlet Inlet
A
A
PAGE 22
HOLDER ACCESSORIES
STUDS AND NUTS of the appropriate length to engage TELL-TALE INDICATOR components between any
the rupture disc insert holder with an inlet and outlet flange two inline pressure relief devices can include the following:
are available in alloy steel1 or 316 SS2 materials. • Gauge taps in the holder outlet: 1/4”, 3/8” or 1/2” NPT
(tap size, location & type may impact holder height)
JACKSCREWS alloy steel: 3 per set • Pipe nipples & tees, CS or SS: 1/4”, 3/8” or
1/2” NPT
EYEBOLTS carbon steel • Excess Flow Valve, 316 SS: 1/4” or 1/2” NPT
• Pressure Gauges
Tell-Tale
Assembly
Nipple
Eyebolts
Pressure
Gauge
1 ASME SA-193-B7 studs, SA-194-2H nuts 2 ASME SA-193-B8M Class 2 studs, SA-194-8M nuts
PAGE 23
LAMOT.COM
Continental Disc Corporation reserves the right to alter the information in this publication without notice. // © 2019 Continental Disc Corporation
Reproduction without written permission is prohibited. LIT1847// 0719