Professional Documents
Culture Documents
ISO 8745-1997 - en
ISO 8745-1997 - en
S T D - B S I B S E N IS0 8745-ENGL 1 7 7 8 W L b 2 4 b b 7 ü b 9 8 7 4 2 7 7 2
BRITISH STANDARD BS EN IS0
8745 : 1998
Grooved pins -
Half-length taper
grooved
ICs 21.060.50
National foreword
This British Standard is the Englishianguagevdon o EN Is08746 : 1997.It is
identical with Is08746 : 1997.it Supeisedes BS EN 28746 : 1992which is
withdrawn.
The UKmcipaüon in its preparation was enírusted by Technical Committee
FME/9,bits,nuts and accessories,to Subcommiaee FME/9/6,Generaì purpose
fasteners and accessories, which has the responsibilib.to:
- aidenquireistoundemîandthe~
- present to the responsible intemationaMhropean c ommim any enquiries
on the mteqretation, or proposals for change, and keep the UK interests
informed;
- monitor relatedintmnationaì and European developments and promulgate
themintheuK.
Summary of pages
This document comprises a front cover,an inside front cover, the EN Is0 title page,
the EN IS0fon?wordpage, the IS0 titie page, page ii, pages 1 to 3,the annex ZA
page, an inside back cover and a back cova
English version
CEN members are bound to comply with the CENICENELEC intemal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Upto-date lists and bibliographicalreferences concerning such national
standards may be obtained on applicationto the Centrai Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretarial has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,
Iceland, Ireland, Italy, Luxembourg, Netherlands, Noway, Poilugal, Spain, Sweden, Switzerland and United Kingdom.
Q 1997 CEN Ail righic of exploitationin any form and by any means reserved Ref. No. EN IS0 87451997 E
worldwide for CEN national Members.
~ ~~
~~
Foreword
The text of the International Standard IS0 87451997 has been prepared by Technical
Committee I S W C 2 "Fasteners" in collaboration with Technical Committee CEWC 185
"Threaded and non-threaded mechanical fasteners and accessories", the secretariat of which
is held by DIN.
This European Standard supersedes EN 287451992.
This European Standard shall be given the status of a national standard, either by publication
of an identical text or by endorsement, at the latest by May 1998, and conflicting national
standards shall be withdrawn at the latest by May 1998.
According to the CEWCENELEC Internal Regulations, the national standards organizations
of the following countries are bound to implement this European Standard: Austria, Beigium,
Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy,
Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United
Kingdom.
Endorsement notice
The text of the International Standard IS0 8745:1997 has been approved by CEN as a
European Standard without any modifications.
NOTE: Normative references to Intemational Standards are listed in annex ZA
(normative).
~ ~~ ~ ~~
INTERNATIONAL IS0
STANDARD 8745
Second edition
1997-11-15
Reference number
I S 0 8745:1997(E)
EN IS0 8746 :1997
Foreword
IS0 (the International Organization for Standardization) is a woridwide
federation of national standards bodies (IS0 member bodies). The work of
preparing International Standards is normally camed out through IC0
technical committees. Each member body interested in a subject for which
a technical committee has been established has the right to be represented
on that cornmittee. Intemational organizations, governmental and non-
governmental, in liaison with ISO, also take pari in the work. IS0
collaborates closely with the International Electrotechnical Commission
(IEC) on all matters of electrotechnical standardization.
1 scope
This International Standard specifies the characteristics of half-length taper grooved pins made of steel or
austenitic stainless steel which have three equally spaced grooves impressed longitudinally on their exterior
surface, with nominal diameter, d,, from 1,5 mm to 25 m m inclusive.
The displaced material to each side of the grooves forming an expanded diameter, d2, which is larger than the
nominal diameter d, will cause a non-positive locking fit when these grooved pins are forced into a drilled hole
equal to the nominal diameter dl(see clause 4).
2 Normative references
The following standards contain provisions which, through reference in this text, constitute provisions of this
International Standard. At the time of publication, the editions indicated were valid. All standards are subject
to revision, and parties to agreements based on this International Standard are encouraged to investigate the
possibility of applying the most recent editions of the standards indicated below. Members of IEC and IS0
maintain registers of currently valid International Standards.
3 Dimensions
See figure 1 and table 1.
I L
1) Chamfer permissible
2) The grooving angle 70" applies only to grooved pins made from steel as shown in clause 5. The grooving
angle may be modified depending on resilience of material
Figure 1
1
EN IS0 8745 : 1997
75 74.25 75.75 - l
80
85
79,25
84.25
80,75
85.75
- 16.6
I
160 I 159.25 160175 I I I 10.35 12,35 16.55
180 I 179,25 I 180.75 I
200 I 1 99 ,sI m,75 I 1 I -
1) Applies only to grooved pins made from steel as shown in clause 5.
2) The range of commercial lengths is between the stepped lines.
3) The expanded diameter d, applies only to pins made from steel as shown in clause 5. For other materials, for ex-
ample stainless steel, a reduction amount shall be subtracted from the given values and should be agreed between
customer and supplier.
4) For testing 4, a GON0 GO ring gauge should be used.
4 Application
The diameter of the hole into which the groove pin is to be inserted shall be equal to the nominal diameter d,
of the mating pin and to tolerance class H11.
2
S T D - B S I B S E N IS0 87Li5-ENGL 1 9 9 8 = Lb24bb7 üb78750 ô49
EN IS0 8746 : 1997
See table 2.
Material? Hardness 125 HV30 to 245 HV30 A l in accordance with IS0 3506-1,
hardness 210 HV30 to 280 HV30
Grooves
6 Designation
EXAMPLE 1
A half-length taper grooved steel pin with nominal diameter d, = 6 mm and nominal length 1 = 50 mm is
designated as follows:
3
~-
=
~~ ~~~ ~
Annex ZA (normative)
Normative references to international publications
with their relevant European publications
This European Standard incorporates by dated or undated reference, provisions from other
publications. These normative references cited at the appropriate places in the text and the
publications are listed hereafter. For dated references, subsequent amendments t o or
revisions of any of these publications apply t o this European Standard only when
incorporated in it by amendment or revision. For undated references the latest edition of
the publication referred to applies.
IS0 8749 -
1986 Pins and grooved pins Shear test EN 28749 1992
3fB~wickHighRoad
London
w4 4AL