Professional Documents
Culture Documents
Basic Logging Measurement: Caliper SP GR NGT Neutron Density Sonic Resistivity Induction
Basic Logging Measurement: Caliper SP GR NGT Neutron Density Sonic Resistivity Induction
Introduction
Caliper
SP
Schlumberger Private
GR
NGT
Neutron
Density
Sonic
Resistivity
Induction
Types of log measurements
Schlumberger Private
• Sonic logs
• Density logs
• Neutron logs
• Resistivity Logs
• Conventional Electrical Logs
• Induction logs
Invasion Model d
Mud
cen t be
Rm
Adja
Uninvaded
zone
Flushed Rt
zone Transition
Schlumberger Private
Rmc Zone Rw
Rxo
Mudcake Rmf
Sw
Bed thickness
Sxo
h n t bed
ce
Adja
me ters
s i on dia
In va
CALIPER LOGS
CALIPER LOGS
- Applications:
• Measure borehole diameter
(borehole geometry if multi-arm
caliper tools with 2 or 3 hole
diameters measurements 90° or
60° relative to each other).
Schlumberger Private
• Important measurement for drillers:
hole geometry, hole/cement
volume.
• Hole diameters are an import input
parameter for the environmental
correction of petrophysical logs.
• Oriented multi-arm caliper logs are
used to identify principle stress
directions - “breakout log”
- Basic Quality Control:
Perform casing check - should read
CALI, C1, C2 Washout: Shale zone? nominal casing ID.
Mudcake: Permeable zone?
SP (Spontaneous Potential Logging)
Schlumberger Private
Spontaneous Potential (SP)
• Opposite shales the SP curve usually
defines a more or less straight line on
the log called the Shale Baseline
• Opposite permeable formations, the
curves shows excursions from the
Schlumberger Private
shale baseline; in thick beds, these
excursions tend to reach an
essentially constant deflection
defining a Sand Line.
• The deflections may be negative or
positive depending primarily on the
relative salinities of the formation
water and of the mud filtrate.
• SP Curve cannot be recorded in holes filled with non conductive
mud, because such mud does not provide the electrical continuity
between the SP electrode and the formation.
• If Rw ~ Rmf => SP deflection will be very small (the curve will be
rather featureless).
Schlumberger Private
•The Position of the shale baseline on the log has no useful meaning
for interpretation purposes. The SP sensitivity scale is chosen and
the shale baseline position is set by the engineer running the log so
that the curve deflections remain the SP track.
Origin of SP
SP deflections result from electric current flowing in the mud in the
borehole. These SP currents are developed by two types of
interactions :
1. Electrochemical
Schlumberger Private
2. Electrokinetic
Electrochemical
The electrochemical interaction is caused by the difference in
salinity between mud filtrate and water formation.
Schlumberger Private
SP – Liquid Junction Potential
Another component of the electrochemical potential is produced at the edge of the
invaded zone, where the mud filtrate and formation water are in direct contact. Here the
Na+ and Cl- can diffuse (move) from either solution to the other. Since Cl- has greater
mobility than Na+, the net result of this ion diffusion is a flow of negative charges from
more concentrated to less concentrated solution. The current flowing across the junction
between solutions of different salinity is produced by an electromagnetic force (emf) called
liquid junction potential.
Schlumberger Private
Schlumberger Private
SP
SP
Schlumberger Private
Membrane potential is about 5 x Liquid Junction potential
Electrokinetic potential SP is negligible
Electro kinetic component of SP
This is generated by the electrolyte flow (of the mud filtrate) through a
permeable, non metallic, porous medium (mudcake).
The magnitude depends on the differential pressure producing the flow
and the resistively of the electrolyte.
Schlumberger Private
In practice, little or no electro kinetic is actually generated. It will only
become important if there are high differential pressures across the
formations
SP as a permeability or shale indicator
Schlumberger Private
of SP can be used to identify
permeable formations.
Schlumberger Private
must correspond to a very clean
sandstone. Rweq SSP
•The value of Rmf must remain
k c
constant across this same interval. 10
These conditions are rare, and large K c 61 0.133T F
errors in the Rw estimate may occur.
Schlumberger Private
If Rmf @ 75 degF < 0.1 Ohmm
then Rmfeq from chart sp2
Same with Rw
SP as Rw indicator
Schlumberger Private
SP is more often used
“qualitatively” to predict
whether Rw > Rmf or not.
-ve SP +ve SP
deflection deflection
Schlumberger Private
SP for correlation
Keep in mind that SP deflection is Rmf dependent and
never an absolute value
Schlumberger Private
SP log
Schlumberger Private
Rmf > Rw?
Where is Sand?
Where is Shale?
What is Vsh?
Static SP (SSP)
SSP is the SP deflection opposite a thick,
clean formation. The deflection is
measured from the shale baseline and its
magnitude:
Rmfe
SSP k log
Schlumberger Private
Rwe
Schlumberger Private
In the opposite condition, Rw>Rmf, found in fresh formation waters, the
deflection is positive (right)
SP Deflection
Negative Rw>Rmf
SP Deflection
Negative Rw<Rmf
Rmf > Rw
Shale Little deflection
Clean Ss Negative deflection
Schlumberger Private
Rmf < Rw
Shale Little deflection
Clean Ss Positive deflection
SP Example
Schlumberger Private
no invasion, a shale.
Rw<Rmf?
Where is Sand?
Where is Shale?
SP reading on Sand?
SPONTANEOUS POTENTIAL – SP
APPLICATIONS
Schlumberger Private
excursions.The percentage of shale can be directly
obtained for any depth on the log by linearly
ESSP scaling between the shale and sand base lines.
For example:
• SPshale = -10 mV
• SPsand = -40 mV
• SPlog = SP reading from the log = -25 mV
• The percentage of shale will be (SPlog -
SPsand) / (SPshale - SPsand) = -15/-30 = .5 or
50% shale.
Code/Name
SP, units = mV
Schlumberger Private
SPONTANEOUS POTENTIAL – SP
APPLICATIONS
• Correlation - Correlation permits logs made on one trip into the borehole to be tied-in
(depth matched) with those made on another trip. Correlating is done for two primary
reasons:
Depth matching between separate trips in the well.
Schlumberger Private
Positioning of open hole sampling tools.
Schlumberger Private
Rmf = Rw Rmf <Rw Rmf >Rw
SALINE MUD FRESH MUD
K = 61 + .133*F
K = 65 + .24*C
Rw From SSP (use this technique with care!)
Schlumberger Private
Resistivity changes with Temperature.
As temperature of the solution increases the activity of the ions in
the solution increases and the solution resistivity decreases.
Since we measure all resistivities at formation temperature (FT)
we must convert the Rmf at surface measured temperature to
Schlumberger Private
Rmf at formation temperature to compute the ratio of Rmf to Rw
(ie SSP).
We assume salinity of the formation does not change with
temperature and use chart Gen. 9.
Rw=0.35 @ 75 degF
What is Rw at 190 degF?? (assuming the salinity does not change
Schlumberger Private
with temperature)
eg. Rw = .35 @ 75F gives a salinity of 17,000ppm. 17,000ppm @ 190 F yields a resistivity of .135 ohmm.
Schlumberger Private
Exercises:
1. Rw = 0.21 ohm-m @ 75 degF.
What is the salinity? 30000 ppm
Schlumberger Private
2. Salinity = 13000 ppm
What is the Rw @ 75 degF? 0.44 ohm-m
If FT= 180 degF, what is Rw? 0.19 ohm-m
Calculation of Rw
from SP
Get Rmf @ meas. Temp from log heading along with BHT.
Compute FT from BHT.
Calculate SSP from log at maximum deflection (in a clean, thick,
Schlumberger Private
zone). --- Just read SP from logs for this training
(water-wet)
Enter Chart SP-1 with SSP, FT., & Rmfe and compute
Rmfe/Rwe.
Compute Rmf @ FT (Gen-9).
Convert Rmf to Rmfe @ FT. from Chart SP-2 Rwe
From Chart SP-2 convert Rwe to Rw at formation temperature.
Schlumberger Private
SP Example for Rw
Schlumberger Private
SP Example for Rw
SP Example for Rw SP-1 Chart
Schlumberger Private
Schlumberger Private
SP Example for Rw
SP Example for Rw
SP-2 Chart
Schlumberger Private
Exercise
Essp = -100 mV @250 degF
Rmf = 0.7 ohm-m at 75 degF
What is Rw?
Schlumberger Private
From SP-1 chart; Rmfe/Rwe = 11.5
Rmfe = 0.85 * Rmf (in condition if Rmf @ 75 degF > 0.1 ohm-m)
Schlumberger Private
Principle
The Gamma Ray log is a measurement of the formation’s natural radioactivity
Gamma Ray emission is produced by three radioactive series found in the
Earth’s crust
Potassium (K40) series
Schlumberger Private
Uranium series
Thorium series
Gamma Ray passing through rocks are slowed and absorbed at a rate which
depends on the formation density
Less dense formation exhibit more radioactivity than dense formations even
though there may be the same quantities of radioactive material per unit
volume.
Gamma ray from decayed formation reaches detector, detector convert
gamma ray into photons these photons are read as electrical signal which are
converted into count rate with international unit API.
The Gamma Ray log environmental correction
Gamma ray affected by nuclie in mud and potassium in drilling fluid , density
and size of borehole.
Oxygen activation correction the emitted artificial high energy neutron from
Schlumberger Private
PNG source exite oxygen nuclie in mud which decay to ground state by
emission of gamma ray this artificial gamma ray affect gamma ray
measurement correction is applied by fact that activated oxygen emits gamma
ray energy higher than highest natural gamma ray which emitted by thorium.
Gamma Ray Interactions
As they pass through matter, gamma rays experience a loss of energy due to
collisions with other atomic particles. These collisions can be divided into three
basic categories :
Schlumberger Private
Pair Production
Compton Scattering
It is the conversion of a gamma ray into an
It is the scattering of a gamma ray by an orbital
electron and positron when the gamma ray
electron. As a result of this interaction, the gamma
enters the strong electric field near an atom's
ray loses energy and an electron is ejected from its
nucleus. It predominates at gamma ray energy
orbit. Compton scattering predominates in the 75 keV
levels above 10 MeV. Because the electron and
to 10 MeV energy range.
positron have a combined mass equivalent of
1.02 MeV, a gamma ray must have at least this
much energy to cause pair production.
GR Log and Uses
Bed definition:
The tool reacts if the shale is radioactive (usually
the case), hence show the sands and shales, the
permeable zones and non-permeable zones Shale
Schlumberger Private
Computation of the amount of shale:
The minimum value gives the clean (100%) shale
free zone, the maximum 100% shale zone. All
other points can then be calibrated in the amount
of shale
Vsh=(GRlog-GRsand)/(GRshale-GRsand)
Reservoir
Schlumberger Private
Application
Correlation
This is the most widely used application of the GR log. It permits logs made on
one trip into the borehole (openhole, cased hole or both) to be tied in (depth
matched) with those made on another trip.
Correlation is done for three primary reasons:
Schlumberger Private
Depth matching between separate trips in the well.
Positioning of open hole sampling tools.
Providing the depth control needed for cased hole perforation.
General lithology indicator
In areas where certain lithology aspects are already known, the GR log can be
used as a lithology indicator.
Quantitative shaliness evaluation
The GR log reflects the proportion of shale and, in many regions, can be used
quantitatively as a shale indicator.
Operating Environment
One of the biggest features of the GR log is its wide range of
operating environments. It can be run in almost any logging
situation including cased wells, or in openholes drilled with
air, salt mud, oil-based mud or fresh mud.
Schlumberger Private
The Natural Gamma Ray Spectrometry
(NGS)
Schlumberger Private
determination of the concentrations of radioactive
potassium, thorium and uranium in the formation rocks.
Principles
Natural Gamma Rays
Gamma ray emission is produced by three radioactive series found in the
Earth's crust.
•Potassium (K40) series, Uranium (U238) series and Thorium (Th 232)
Schlumberger Private
series.
Schlumberger Private
NGT Example
NGT Applications
Lithology identification
Study of depositional environments
Investigation of shale types
Schlumberger Private
Correlation of the GR for clay content evaluation
Identification of organic material and source rocks
Fracture identification
Geochemical logging
Study of s rock’s diagenetic history
A major application was to solve North Sea log interpretation problems in
micaceous sands
NGT Elements
The three radioactive elements measured by the NGT occur in different parts of the
reservoir. If we know the lithology, we can deduce further information
In Carbonates:
U - indicates phosphates, organic matter and stylolites
Schlumberger Private
Th – indicates clay content
K – indicates clay content, radioactive evaporites
In sandstone:
Th – indicates clay content, heavy minerals
K – indicates micas, micaceous clays and feldspars
NGT Elements (continued)
In shales:
U – in shale, suggest a source rock
Th – indicates the amount of detrital material or degree of shaliness
K – indicates clay type and mica
Schlumberger Private
NGT/GR Parameters
Vertical resolution 18”
No formation is perfectly clean, hence the
GR readings will vary. Limestone is Depth of investigation 6”-8”
usually cleaner than the other two
reservoir rocks and normally has a lower Readings in: API units
Schlumberger Private
GR Limestone <20
Anhydrite and salt are normally very Dolomite <30
clean, and have very low values
Sandstone <30
Shale 80-300
Salt <10
Anhydrite <10
Code/Name
GR
CGR
SCGR
Schlumberger Private
POTA
THOR
URAN
*GR
Exercise
What is the VSH from GR @ 10235
ft?
Approximately 43%
Shale
Schlumberger Private
VSH = (GR log – GR sand) /
(GR shale – GR sand)
GR log example
Schlumberger Private
Porosity Logs
The major porosity logs are:
Neutron Logs, n The tool response is
Density Logs, b affected by the formation
porosity, fluid and matrix.
Sonic Logs, t
Schlumberger Private
If the fluid and matrix effects are known or can be determined, the
tool response can be related to porosity, therefore these devices
are referred to as porosity logs.
Schlumberger Private
Sonic Logging
Sonic Logs
Principles :
In its simplest form, a sonic tool consists of :
A transmitter that generates a sound pulse
Schlumberger Private
A receiver that picks up and records the pulse as it
passes the receiver.
Schlumberger Private
Sonic Tool
The sonic tools create an acoustic signal and measure how long it takes to pass through a rock.
Schlumberger Private
By simply measuring this time we get an indication of the formation properties.
The amplitude of the signal will also give information about the formation.
Borehole Compensated Sonic (BHC)
Schlumberger Private
transit times
Used for:
Correlation
Porosity
Lithology
Seismic tie in / time-to-depth conversion
Long Spacing Sonic (LSS)
Schlumberger Private
The tool cannot be built with transmitters at each end like a BHC
sonde, hence there are two transmitters at the bottom
A system called DDBHC – depth derived borehole compensation, is
used to compute the transmit time
Same as the BHC tool for applications
Array Sonic: Digital Sonic Tool
Schlumberger Private
Used for:
Porosity, lithology
Seismic tie/ time-to depth conversion
Mechanical properties (from shear and compressional)
Fracture identification (from shear and Stoneley)
Permeability (from Stoneley)
Array Sonic: Digital Sonic Tool (cont.)
Schlumberger Private
Sonic Logs
Rec1
Schlumberger Private
Rec8
Schlumberger Private
porosity.
STANDARD DISPLAY OF
BOREHOLE COMPENSATED
SONIC LOG (BHC)
- Primary Logging Curves:
Schlumberger Private
DT … Delta Time or Slowness
[μsec/ft; μsec/m]
TT1 - 4 … Transit Times [μsec] for Log
Integrated Transit Time Quality Control
- Optional Logging Curves:
SPHI … Sonic Porosity [vol/vol]
SVEL … Sonic Velocity [ft/sec; m/sec]
- Sonic Specific Output:
Cycle Skip Integrated Transit Time for
comparison with Seismic One Way
Time
- Basic Quality Control:
Check for Cycle Skips and TT1 - TT4.
These curves should run in parallel.
POROSITY LOGS SONIC TOOL
Schlumberger Private
DT4S … DTshear, Shear Slowness [μsec/ft;
μsec/m]
- Optional Logging Curves:
VpVs…. Dtshear/Dtcomp
PR…….. Poisson’s Ratio
Schlumberger Private
measurement of compressional and shear
wave slowness can help us estimate:
Porosity (estimated from the
compressional slowness measured by the
sonic log.
Lithology
Presence of natural gas
Determination of Lithology with Cross Plot
Application of Sonic Logs
Detection of the presence of natural gas
Schlumberger Private
Application of Sonic Logs
Schlumberger Private
completion process.
The Cement Bond Log shows how the
amplitude of the waveform increases when
there is poor cement and decreases in the
intervals when there is good cement.
Vertical Resolution:
Standard STC (BHC,LSS,MSTC) 24”
Sonic 36”
Parameters
6” DT 6”
Depth of investigation BHC(5”) LSS-SDT(12”)
Schlumberger Private
Readings in zero porosity: (With 12 feet spacing)
Limestone (0pu) 47.5 us/ft
Sandstone (0pu) 51-55 us/ft
Dolomite (0pu) 43.5 us/ft
Anhydrite 50 us/ft
Salt / Coal 67 / >120 us/ft
Shale >90 us/ft
Steel (casing) 57 us/ft
Code/Name
DT
AC
DT*
Schlumberger Private
Sonic Porosity
The porosity from the sonic slowness is different than that from the density or neutron tools
It reacts to primary porosity only, I.e. it doesn’t “see” the fracture or vugs
The difference between the sonic porosity and the neutron-density porosity gives a Secondary
Porosity Index (SPI) which is an indication of how much of this type of porosity there is in the
Schlumberger Private
formation
The basic equation for sonic porosity is the Wyllie Time Avearge:
t log t f 1 t ma
t log t ma
t f t ma
Sonic Porosity (continued)
The Wyllie Time Average equation is very simple with the inputs of a matrix slowness and a
fluid slowness
There is another possibility for transforming slowness to porosity, called Raymer Gardner Hunt,
this formula tries to take into account some irregularities seen in the field. The basic equation
is:
Schlumberger Private
1
1
2
t c t ma t f
A simplified version used on the Maxis is: (C is a constant, usually taken as 0.67 )
t log t ma
C
t log
Sonic Porosity Chart
Schlumberger Private
known prior to using this chart
This chart is entered with the interval
transit time, move up to the lithology
line and read the porosity
Exercise
Calculate Sonic
Porosity @10200 ft
assuming the matrix
delta is 65 sec/ft and
Schlumberger Private
the fluid delta t is 189
sec/ft.
Density - Lithology
The density logging tool measures the formation density and
formation lithology.
Schlumberger Private
Density Tool History
Schlumberger Private
Density
Principles :
Gamma Ray Interactions
Schlumberger Private
Gamma Ray Interactions depend on the current Gamma Ray’s energy level
Gamma Ray Source
•Use of chemical source.
•Gamma Ray energy level is generated in Campton Scattering
range (77 keV – 100 MeV).
Schlumberger Private
Gamma Ray Detection
•Gamma rays lose their energy when they collide with electrons (Campton Scattering)
•The number of Compton-scattering collision is related directly to the number of electrons in
the formation. Consequently, the response of the density tool is determined essentially by
the electron density. Understanding the relationship between electron density and bulk
density is an essential part of the density measurement.
Schlumberger Private
Relationship between Electron Density to Bulk Density
Schlumberger Private
•The source-to-detector spacing must be as such that the gamma rays travel
farther into the formation without losing their energy when they reach the
detector.
Porosity from Density
Schlumberger Private
Photoelectric Effect Measurement
Schlumberger Private
measurement is having the counts of
gamma rays drop in the energy region
where photoelectric interactions
predominates.
• The spectrum represents the energy lost by gamma rays (emitted from the source)
as they interact with the formation.
• Plot 1 shows the different regions of the energy spectrum.
Photoelectric Effect Measurement
Schlumberger Private
can predict the lithology of the formation.
Photoelectric Effect Measurement
Schlumberger Private
LDT Uses
The density tool is extremely useful as it has high accuracy and exhibits
small borehole effects
Major uses include:
Porosity
Schlumberger Private
Lithology (in combination with the neutron tool)
Mechanical properties (in combination with the sonic tool)
Acoustic properties (in combination with the sonic tool)
Gas identification (in combination with the neutron tool)
Borehole diameter - A single axis diameter of the borehole is measured from the face
of the skid pad to the end of the caliper arm that holds the skid against the formation.
Typical Density Response
Schlumberger Private
POROSITY LOGS- DENSITY & PHOTOLECTRIC EFFECT
Schlumberger Private
LDT Parameters
Vertical Resolution:
Standard 18”
Enhanced 6”
Schlumberger Private
Depth of Inverstigation 6”-9”
Readings in zero porosity:
Vertical Resolution:
Standard 4”
Schlumberger Private
Readings in zero porosity:
Limestone 5.08
Sandstone 1.81
Dolomite 3.14
Anhydrite 5.05
Salt 4.65
Shale 1.8-6
Code/Name
RHOB
RHOZ
DEN
Schlumberger Private
RHO*
PEF
PE
Density Porosity
b f ma 1
ma b
Schlumberger Private
ma f
There are two inputs into the porosity equation: the matrix density and the fluid density
The fluid density is that of the mud filtrate
Por-5: Density Porosity
Schlumberger Private
12 p.u
2.46 g/cc
Clean Sand Formation Porosity:
Density
ρb = (1-Φd) * ρma + Φd * ρf
ma b
D
Schlumberger Private
ma f
ρ
For ma:
Sandstone: 2.65 g/cc
Limestone : 2.71 g/cc
Dolomite : 2.87 g/cc
Scaling/Porosity
The density tool is usually run with the neutron
To aid quicklook interpretation they are run on “compatible
scales”
Schlumberger Private
This means that the scales are set such that for a given
lithology the curve overlay
Scaling/Porosity (continued)
The standard scale is the “limestone compatible” where the neutron porosity scale is:
To fit this, the density log has to have its zero limestone point (2.7 g/cc) on the same
Schlumberger Private
position as the neutron porosity zero and the range of the scale has to fit the neutrons
60 porosity units hence the scale is:
Changing to a sandstone compatible scale would put the zero sandstone density,
2.65, over the neutron porosity zero to give:
Exercise
Schlumberger Private
Density Por ~33%
Neutron
Schlumberger Private
response of these neutrons as they interact
with the formation, or in many cases, the fluids
within the formation. This measured response
is affected by the quantity of neutrons at
different energy levels and by the decay rate of
the neutron population from one given energy
level to another. A neutron interacts with the
formation in a variety of ways after leaving the
source, it is the aftermath of these interactions
that is detected by the tool.
Neutron logs are used principally for delineation of porous
formations and determination of their porosity.
Neutron logs respond primarily to the amount of hydrogen in the
formation. Thus, in clean formations whose pores are filled with
Schlumberger Private
water or oil, neutron log reflects the amount of liquid-filled porosity.
Gas zones can often be identified by comparing the neutron log
with another porosity log or a core analysis.
Neutrons are electrically neutral particles, each having a mass almost identical to
the mass of a hydrogen atom.
When emitted from the radioactive source, the neutrons will collide with nuclei of
the formation materials (billiard-ball collisions). This causes the neutron to lose
some energy.
The loss of energy per collision depends on the relative mass of nucleus with
Schlumberger Private
which the neutron collides. The greater energy loss occurs when neutron strikes
hydrogen nucleus (having equal mass).
The slowing of neutrons depend largely on the amount of hydrogen in the
formation.
When hydrogen concentration in the formation is large, most of neutrons are
slowed and captured within short distance of the tool. On the contrary, if the
hydrogen concentration is small, the neutrons travel farther from the course
before being captured.
The response of neutron tools primarily reflects the amount of hydrogen in the
formation. Since oil and water contain practically the same quantity of hydrogen
per unit volume (HI), the responses reflect the liquid-filled porosity in clean
formations.
Schlumberger Private
Liquid hydrocarbons have HI close to that of water. Gas, however, has lower
hydrogen concentration, hence neutron log reads too low a porosity. This
characteristic allows the neutron log to be used with other porosity logs to detect
gas zones and identify gas/liquid contacts.
A neutron and density log combination provides a more accurate porosity.
Neutron – Principles of Operation
Schlumberger Private
The Figure shows that the neutron slows down to a thermal energy level at a fairly
quick rate. The slowing down rate is determined by the hydrogen index (HI) of all
components of the formation and formation fluids that contain a significant fraction of
hydrogen.
Example of NEUTRON LOGS
STANDARD DISPLAY OF
COMPENSATED NEUTRON
LOG (CNL)
- Primary Logging Curves:
TNPH … Neutron Porosity [vol/vol]
Schlumberger Private
(NPHI*… Neutron Porosity [vol/vol])
* obsolete replaced by TNPH
Schlumberger Private
CNT (Compensated NT) Parameters
Vertical Resolution:
Standard (TNPH) 24”
Enhanced 12”
Schlumberger Private
Depth of Investigation 9”-12”
Readings in zero porosity:
Limestone(0%) 0
Sandstone(0%) -2
Dolomite(0%) 1
Anhydrite -2
Salt -3
Shale 30-45
Coal 50+
Code/Name
NPHI
TNPH
CN
Schlumberger Private
CNL
CNT Uses
Schlumberger Private
Combined with the bulk density, it gives the best possible answer for
lithology and porosity interpretation
It can be used in cased hole
CNT in Cased Hole
The CNT can be run in cased hole for the porosity
In addition to the standard corrections some others are needed to take into account
the extra elements of casing and cement
The standard conditions are:
8 ¾” borehole diameter
Schlumberger Private
Casing thickness 0.304”
Cement thickness 1.62”
Fresh water in the borehole and formation
No stand-off
75F
Atmosphere pressure
Tool centred in the hole
Clean Sand Formation Porosity:
Neutron Matrix Correction (Chart)
NPHI = (1-Φn) * NPHIma + Φn * NPHIf
Schlumberger Private
(NPHI – NPHIma)
Φn = ---------------- (Chart Por-13b)
(NPHIf – NPHIma)
38 p.u in Ss
Schlumberger Private
33.5 p.u in LS
Archie’s Equation
Empirical constant
a Rw
(usually near unity) Resistivity of
formation water,
Schlumberger Private
Sw n
-m
Water m Cementation
exponent
Rtt
saturation,
fraction (usually near 2)
Saturation
exponent
(also usually Resistivity of
near 2) Porosity, uninvaded
fraction formation, -m
Archie Parameters
Schlumberger Private
a = constant, set to 1 in the simple case
All the constants have to be set
Two common sets of numbers for these constants are:
In a simple carbonate, the parameters are simplified to:
m=2, n=2, a =1
1 1
Sw Vcl *
1
Vcl
2
e Rt
Rcl
Rw
2
1 n
Schlumberger Private
1.4 m
V 2
e
Sw
cl
Rt Rcl aRw
1 Sw2 BQv Sw
* *
Rt F Rw F
Ct
m
t Sn
wt
Cw
Swb
Cwb Cw
a
Swt
Rw Determination
• Rw from SP
Rw=(Φ^m)*Rt
Schlumberger Private
• Rw from resistivity only (wet zone)
Rt*Rmf
Rw = --------------
Rxo
• Rw from client (water chemical analysis)
Schlumberger Private
•Chart Gen-9
Exercise
Rt = 20 ohm-m
Rw = 0.6 ohm-m @ 75 degF
= 0.2 ; Vcl = 0
Schlumberger Private
BHT = 150 degF
M=n=2 ; a = 1
What is water salinity? 10Kppm
What is Rw @ 150 degF? 0.3 ohm-m
What is Sw? 0.61
Exercise
Rt = 100 ohm-m
Salinity (Cl-) = 45 Kppm
= 0.22 ; Vcl = 0
Schlumberger Private
BHT = 180 degF
M=n=2 ; a = 1
What is salinity (NaCl)? 74 Kppm
What is Rw @ 180 degF? 0.04 ohm-m
What is Sw? 0.09
Clean Sand Formation Workflow
(Density-Neutron)
ma b
D
ma f Φd Φn
dphi
2
nphi
2
Schlumberger Private
x
Crossplot porosity Φ1 2
Rw from SP or Rwa m Rt
Rw
1/ n
a Rw
Sw Sw
m R
t
I Rt / Ro 1 / Sw m
F 1 / m Ro / Rw
Electric Resistivity Logging
Schlumberger Private
Resistivity Logs
Resistivity is one of the primary inputs required to evaluate the producing potential of
an oil or natural gas well. This measurement is needed to determine Sw, which is
needed to estimate the amount of oil or natural gas present in the well.
Schlumberger Private
Resistivity of the formation water
The amount of water
Pore structure geometry
Principles
(Conventional electrical logs)
Currents were passed through the formation from the current
electrodes and voltages were measured between measuring
electrodes.
Focusing
It is forcing the electrical currents to flow in the formation in the situation where the formation
resistivity gets high.
Laterolog devices are focused devices. The term laterolog came about because the current is
forced to flow "laterally" away from the tool.
Schlumberger Private
There are three types of focusing systems in use today:
Passive Focusing Systems – DLL, ARI
Active Focusing Systems - ARI
Computed Focusing - HRLA
Example of Passive Focusing Passive Focusing Systems
Laterolog measurements began with a
device called the bucking electrode.To
focus the measured current laterally into
the formation, bucking electrodes are
place above and below the measure
Schlumberger Private
electrode. As shown in "Passive
Focusing" graphic, equal current is
emitted from all three electrodes to focus
the current into the formation. With this
arrangement, the equipotential shapes
distort very quickly. This electrode
configuration is called the Laterolog
Three (LL3) and is known as a passive
bucking system
Distortion of equipotential
surfaces
Example of Active Focusing
Active Focusing
To maintain the shape of the equipotential
surfaces and ensure the measured current
is flowing laterally into the formation in
formations of higher resistivities, the active
bucking system was introduced (LL5
Schlumberger Private
device). As shown in the "Active Focusing"
graphic, this system places two voltage
electrodes, M1 and M2, between the
current-emitting measure electrode and the
bucking electrode. The measured current is
adjusted until the voltage difference
between M1 and M2 is zero. This ensures
that the area in front of these monitor
electrodes is equipotential and the
measure current is flowing laterally away
from the tool. This is known as the
laterolog deep (LLD) measurement.
Computed Focusing
The Laterolog Tool uses the main monitoring condition of M1 - M2 = 0 as the main control condition.
Limited Dynamic Range. To maintain M1 - M2 conditions in very high resistivities requires infinite gain.
Temperature Variations. Variations in temperature introduce errors in the measurements.
Continued developments in data processing, transmission, and digital conversion capabilities have made it
Schlumberger Private
possible to take advantage of some electromagnetic principles, specifically the principles of electromagnetic
superposition. These capabilities allow us to obtain focused measurements through computations instead of by
mechanical means. The principles of computed focusing allow us to maintain the condition of M1 - M2 = 0 by
mathematically combining linear combinations of pairs of operating modes. These operating modes and the
combinations used to obtain the different depths of investigation are shown in the "Computed Deep Focusing"
and the "Computed Shallow Focusing" diagrams. Array laterolog devices have multiple operating modes that
are combined together to obtain a series of computed focusing modes with increasing depths of investigation.
An in-depth discussion of these modes is beyond the scope of this text.
Example of Computed Focusing
Schlumberger Private
Depth Of Investigation
Different depths of investigation are obtained by varying lengths of bucking current electrodes.
Shallow Focusing
If the current is returned to the tool body, instead of the surface electrode, the equipotential
surfaces distort very quickly and the resistivity measurement is influenced by events very close or
Schlumberger Private
shallow to the tool. This is known as the laterolog shallow (LLS) measurement.
Deep Focusing
In this system the currents are returned to the surface electrode instead of the tool body. This
maintains the shape of the equipotential surfaces much deeper into the formation insuring the
measure current is flowing deeper into the formation than the shallow measurement. To measure
both the shallow and deep depths of investigation simultaneously is very desirable to help estimate
the invasion profile for more accurate measurements. The Dual Laterolog (DLT), a device that
measures at two depths of investigation was developed for this purpose.
This tool combines the measurement principles of the LLD and LLS into a single device by having
each measurement operate on a different frequency.
Depth Of Investigation
Invaded Zone or Rxo Devices
To complete the borehole description, devices were developed that measured at very
shallow depths of investigation in the invaded zone (Rxo), also referred to as the
flushed zone. These devices use the principles of active and passive focusing and
change the distance between the emitting electrodes and the return electrode to
Schlumberger Private
achieve very shallow depths of investigation. Example of the tools are MSFL, Microlog
and MCFL.
Azimuthal Resistivities
Azimuthal resistivities are resistivity measurements made around the circumference
of the borehole. Azimuthal measurements are very useful in evaluating highly
deviated and horizontal boreholes.
Depth Of Investigation
Schlumberger Private
the main goal of this type of measurement.
Laterolog Borehole Effects
Laterologs measure Resistivity in Series
Laterologs see the borehole environment as
RLL=Rm+Rmc+Rxo+Rt
Schlumberger Private
Best measurement is in salt
saturated, low resistivity mud.
Worst readings obtained in fresh
mud.
Measurement can’t be taken in OBM
Schlumberger Private
Shallow: MSFL,AIT10,RLA1
The equation can be solved using Tornado charts
Several charts exist: one for each possible configuration of the resistivities. The correct one must be chosen
for each situation
There are zones on each chart where the solution is impossible, this is where the tool is being run outside its
specifications or the corrections have not been properly applied
Example Tornado Chart
Schlumberger Private
Code/Name
Deep: RT,LLD,RLA5,RT*
Medium: LLS,RLA3
Shallow: RXO,MSFL,SFLU,RLA1/RLA2
Schlumberger Private
RESISTIVITY - DUAL LATEROLOG LOG EXAMPLE
STANDARD DISPLAY OF
(PHASOR) INDUCTION LOG (PI)
- Primary Logging Curves:
LLD … Deep Laterolog Resistivity [Ωm]
LLS… Shallow Laterolog Resist. [Ωm]
Schlumberger Private
SP*…... Spontaneous Potential
* not shown on this display
- Basic Quality Control:
Dual Laterolog readings for formation
resistivities < 1.0 Ωm become inaccurate -
Induction might have been the better
choice. LLS can be severely affected in
large holes - washouts - and not be in
agreement with LLD (LLD less sensitive to
borehole conditions).
Because laterolog tools have the ability to control the region of investigation in
Vertical, radial and azimunthal directions, these tools have additional apps :
Schlumberger Private
Evaluate mud cake and mud resistivity for borehole correction using very shallow
measurements.
Enhance the evaluations of horizontal and or highly-deviated wells using azimuthal and array
measurements.
Fracture analysis using azimuthal measurements.
Enhance the evaluations of thin and invaded formation using array measurements.
Enhance the accuracy of Rt evaluation in difficult environments such as Groningen affected
areas, high contrasts, thinly bedded formations and high apparent dip by using array
measurements and formation inversion processes.
Open Hole Formation Evaluation
Schlumberger Private
Section 10:
Induction Logging
Induction Theory
An induction tool uses a high
frequency electromagnetic
transmitter to induce a
current in a ground loop of
formation
Schlumberger Private
This, in turn, induces an
electrical field whose
magnitude is proportional to
the formation conductivity
Induction Logs
Induction Principles :
A high-frequency AC of constant intensity is sent through a transmitter
coil -> magnetic field -> create currents in the formations as ground
loops coaxial with the transmitter coil -> magnetic field that induces a
Schlumberger Private
voltage in the receiver coil.
Induction tool works best when the borehole fluid is an insulator, air or
gas, even when the mud is conductive.
Induction: Borehole Effects
Schlumberger Private
Cm: Best readings occur in high resistivity mud, OBM is better,
fresh mud is good, salt-saturated mud is worst
Cmc: usually neglected as very small
Cxo: depends on Rmf – needs to be known
Ct: Parameter to be measured, the higher the better
Code/Name
Deep: RT,ILD,IDPH,AIT90,RT*
Medium: ILM,IMPH,AIT30/AIT60, A*
Shallow: RXO,MSFL,SFLU,AIT10/AIT20, A*
Schlumberger Private
RESISTIVITY - INDUCTION Log Example
STANDARD DISPLAY OF
(PHASOR) INDUCTION LOG (PI)
- Primary Logging Curves:
IDPH … Deep Induction Resistivity [Ωm]
IMPH… Medium Induction Resist. [Ωm]
Schlumberger Private
SFL* … Spherical Focused Log [Ωm]
SP*…... Spontaneous Potential
* not shown on this display
Laterolog Induction
OBM no yes
Possible in small holes*
Salt Water Mud yes
Schlumberger Private
Fresh mud No** yes
High resistivity yes no
Air-filled hole no yes
Low resistivity Possible*** yes
Rt<Rxo Induction prefered
Rt>Rxo Laterolog
Prefered
FMI image versus core
Schlumberger Private
AUXILIARY LOGS
• TEMPERATURE MEASUREMENT
Vital Input Log Analysis:
Fluid resistivity changes with temperature - Rw (formation water resistivity)
Schlumberger Private
and Rmf (mud filtrate resistivity) vary with temperature.
Temperature/Mud Resistivity Measurements:
- Maximum Thermometer’s: Thermometers tied to the tool string and read once
the string returns to surface. The time the tool string reaches the bottom of the
well is recorded on the log header together with the temperature reached. Using
the maximum recorded temperature a linear temperature gradient is established
to correct mud sample measurements to down-hole conditions.
- Auxiliary equipment such as the Environmental Measurement Sonde (EMS) or
auxiliary sensors on logging equipment such as the Platform Express perform
continuous recording of temperature and mud sample resistivity.
LOGGING RESULTS DELIVERABLES
Schlumberger Private
Certain measurements are being delivered with Log
Quality Displays verifying the quality of the data
recorded.
LOG HEADER - includes all information about the well logged and information
necessary to describe the environment the measurement has been
informed in (e.g. drilling mud parameters). Tool sketches and
Schlumberger Private
remarks informing about specific events during the logging
operation complete the header.
REPEAT SECTION - short section of log to prove repeatability of log or re-log of sections
with measurement anomalies.
Schlumberger Private
LOG DISPLAY LOG HEADER 2
Schlumberger Private
LOG DISPLAY LINEAR SCALE
Schlumberger Private
LOG DISPLAY LOGARTIHMIC SCALE
Schlumberger Private
LOG DISPLAY LOG TRAILER 1
Tool/Computation
Schlumberger Private
Parameter Table
LOG DISPLAY LOG TRAILER 2
Calibration
Schlumberger Private
and Check
Summary
LOG DISPLAY LOG TRAILERS (3)
Schlumberger Private
Tool Calibration
Details
Petrophysical Analysis Results
Schlumberger Private