Professional Documents
Culture Documents
Huawei eRAN3.0 CSFB Feature Introduction
Huawei eRAN3.0 CSFB Feature Introduction
0
CSFB Feature Introduction
www.huawei.com
Apr. 2006
CSFB to
CDMA2000 1xRTT
MSC-VLR HSS/HLR
NodeB RNC
Inter-system change
SGSN
SGs
3G
LTE
n
dir ectio
S re MME
HO or P
1. Ext Service RQ 4. PS d icato
r)
(CSFB indicator) FB i n
e (CS
e ssag
3.optional measurement AP M
2. S1
eNodeB SAE-GW
5. eNB direct the UE to
G/U
RAT change (and selection) is under full network control (eNodeB triggers the
RAT change towards to 2G/3G based on the UE’s capability\measurement\SPID
indication from MME.)
3G
Re
SGs
n
in g
LTE ctio
ire
ag
red
8.P
PS MME
O or
SH )
6. P ator
ic
ind
B
CSF
2. Paging RQ e (
ag
(Domain indicator: ess
CS) M
3. Ext Service RQ (CSFB AP
S1
indicator)
5.measurement 4.
eNodeB SAE-GW
7. eNB direct the UE to G/U
UE eNodeB RNC MME MSC SGSN UE eNodeB RNC MME MSC SGSN S-GW
P-GW
1. Extended Service Request 1.Paging Request
(containing a CS Fallback Indicator)
Paging
2. S1-AP Message
(containing a CS Fallback Indicator) 2.Extended Service Request
(containing a CS Fallback Indicator)
S1-AP Response Message
Service
Request
3. Optional measurement report
3. S1-AP message with CS Fallback indicator
4. PS handover preparation phase
Handover Command
Handover 4. Subsequent procedure similar to that in a mobile-originated case, with the CS
Command call establishment procedure replaced with a Paging Response message
UE eNodeB RNC MME MSC SGSN UE eNodeB RNC MME MSC SGSN
5. LAU, combined RAU/LAU, or RAU and LAU 5. LAU, combined RAU/LAU, or RAU and LAU
PS Suspend PS Suspend
In case GERAN or UE can’t support DTM (Dual transfer Mode) the PS service will be suspended
5.LAU, combined RAU/LAU, or RAU and LAU 5.LAU, combined RAU/LAU, or RAU and LAU
6.Suspend 6.Suspend
4. MobilityFromEUTRACommand
(CCO optionally with NACC)
5. S1 UE context release
7.Suspend
In case GERAN or UE can’t support DTM (Dual transfer Mode) the PS service will be suspended
Page 12
HUAWEI TECHNOLOGIES CO., LTD. Huawei Confidential
CSFB to UTRAN: Three mechanisms
E-UTRAN may use the emergency indication for selecting a particular radio access
network (2G or 3G) for CS emergency handling.
If PS handover is initiated, E-UTRAN may indicate priority level of the CSFB to the
target RAT, in order to prepare radio resource at target RAT in appropriate way,
e.g. priority allocation of the RAB resource.
开始 Triggering phase
The eNodeB receives a CS Fallback Indicator from the
收到CS Fallback Indicator
MME. If the eNodeB supports blind handovers to an
inter-RAT system, it performs a blind handover without
CSFB触发: 是
delivering the measurement configuration to the UE.
是否盲切换
Otherwise, the eNodeB delivers the measurement
否
测量超时或异常 configuration to the UE. Compared with measurement-
CSFB测量
based handovers, blind handovers can reduce the
R8 CSFB
Blind Scenario :
A list of candidate cells is generated on the basis of the blind handover priorities, which are determined by
both the RAT-specific priorities and the cell-specific priorities.
The RAT-specific priorities used in blind handovers for CSFB are defined through the InterRatHighestPri,
InterRatSecondPri, and InterRatLowestPri parameters.
Measure Scenario :
eNB sends the UE the measurement configuration, according to which the UE performs measurements on the
specified system. The measurement configuration sent to the UE contains the configuration information for
only the RATs and frequencies that are supported by the UE.
eNB selects the best cell from UE’s measurement report.
RAN information
information
Frequency and
request
2. BSC/RNC reply system information. If system
RAN
target cell
BSC/RNC system information update , BSS/RNC notify eNodeB and
information
send the latest information;
CSFallBackHo CsfbHoUtranB1ThdECN0 Indicates the Ec/No threshold for event B1, which is used in CS fallback to UTRAN.
When CS fallback to UTRAN is applicable, this parameter is set for UEs and used
in the evaluation about whether to trigger event B1. This parameter indicates the
Ec/No requirement for the UTRAN cells to be included in the measurement report.
A UE sends a measurement report related to event B1 to the eNodeB when the
Ec/No in at least one UTRAN cell exceeds this threshold and other triggering
conditions are met. For a cell with large signal fading variance, set this parameter
to a large value to prevent unnecessary handovers. For a cell with small signal
fading variance, set this parameter to a small value to ensure that the handover is
performed in time. For details, see 3GPP TS 36.331.
CSFallBackHo CsfbHoGeranB1Thd Indicates the RSSI threshold for event B1 that is used in CS fallback to GERAN. A
UE sends a measurement report related to event B1 to the eNodeB when the RSSI
in at least one GERAN cell exceeds this threshold and other triggering conditions
are met. For details, see 3GPP TS 36.331.
CSFallBackHo CsfbHoCDMAB1ThdPS Indicates the pilot strength threshold related to event B1, which is used in CS
fallback to CDMA2000. A UE sends a measurement report related to event B1 to
the eNodeB when the pilot strength in at least one CDMA2000 cell exceeds this
threshold and other triggering conditions are met. For details, see 3GPP TS
36.331.
CSFallBackHo CsfbHoUtranTim 40ms 0ms, 40ms, 64ms, 0ms, 40ms, 64ms, ms MOD CSFALLBACKHO
eToTrig 80ms, 100ms, 128ms, 80ms, 100ms, LST CSFALLBACKHO
160ms, 256ms, 320ms, 128ms, 160ms,
512ms, 480ms, 640ms, 256ms, 320ms,
CSFallBackHo CsfbHoGeranTim40ms ms MOD CSFALLBACKHO
1024ms, 1280ms, 512ms, 480ms,
eToTrig LST CSFALLBACKHO
2560ms, 5120ms 640ms, 1024ms,
1280ms, 2560ms,
CSFallBackHo CsfbHoCDMATi 40ms 5120ms ms MOD CSFALLBACKHO
meToTrig LST CSFALLBACKHO
G/U LTE
coverage UL dual coverage
mode UE