Professional Documents
Culture Documents
0-Flight Controls - Ders Tanıtım
0-Flight Controls - Ders Tanıtım
Ders Tanıtım
Hazırlayan
Dou you know how it works?... Can you perform some tasks if we give you some guidlines?
Table of Contents
LEVEL 1
• A familiarisation with the principal elements of Module 13.7 Flight Controls (ATA 27)
the subject.
Objectives: The applicant should be familiar with 13.7 (a)
the basic elements of the subject. o Control System Overview (1.1, 1.2, 2.1, 2.3)
1.1. The applicant should be able to give a simple o Primary controls: aileron, elevator, rudder, spoiler Trim Control (1.1, 1.2, 2.1, 2.3)
description of the whole subject, using common o Pitch Trimming (1.1, 1.2, 2.1, 2.3)
words and examples. o Versine Signal (1.1, 1.2, 2.2) (2.2: Sadece bir tane çok basit formül)
1.2. The applicant should be able to use typical o Active Load Control (1.1, 1.2, 2.1, 2.3)
terms. o High Lift Devices (1.1, 1.2, 2.1, 2.3)
o Lift Dump and Speed Brakes (1.1, 1.2, 2.1, 2.2, 2.3) (2.3: Çalışma prensibi/ lojik devre)
LEVEL 2 o Torque Limiting (1.1, 1.2, 2.1, 2.3)
• A general knowledge of the theoretical and o Artificial Feel and Centring (1.1, 1.2, 2.1, 2.3)
practical aspects of the subject. o Flutter Damping (1.1, 1.2, 2.1, 2.3)
• An ability to apply that knowledge. o Yaw Damper (1.1, 1.2, 2.1, 2.2, 2.3) (2.3: Az bişey ayrıntılı bir çalışma prensibi şeması)
Objectives: The applicant should be able to o Mach Trim (1.1, 1.2, 2.1)
understand the theoretical fundamentals of the o Rudder Limiter (1.1, 1.2, 2.1, 2.3)
subject. o Gust Locks (1.1, 1.2, 2.1)
2.1. The applicant should be able to give a general o Stall Protection Systems (1.1, 1.2, 2.1, 2.3)
description of the subject using, as appropriate,
typical examples. 13.7 (b) - Fly By Wire
2.2. The applicant should be able to use o Basic Principle (1.1, 1.2, 2.1, 2.2, 2.3) (2.3: Çalışma prensibi şeması)
mathematical formulae in conjunction with physical o Control Surfaces (1.1, 1.2, 2.1, 2.3)
laws describing the subject. o Cockpit Controls (1.1, 1.2, 2.1, 2.3)
2.3. The applicant should be able to read and o Computers (1.1, 1.2, 2.1, 2.2, 2.3) (2.3: Çalışma prensibi şeması)
understand sketches, drawings and schematics o Pitch Control (1.1, 1.2, 2.1, 2.2, 2.3) (2.3: Çalışma prensibi şeması)
describing the subject. o Roll Control (1.1, 1.2, 2.1, 2.2, 2.3) (2.3: Çalışma prensibi şeması)
2.4. The applicant should be able to apply his o Speedbrakes and Ground Spoilers (1.1, 1.2, 2.1, 2.2, 2.3) (2.3: Çalışma prensibi/ lojik devre)
knowledge in a practical manner using detailed o Protections (1.1, 1.2, 2.1, 2.2, 2.3) (2.2: Birkaç tane limit değer ve/veya aralık)
procedures.