Professional Documents
Culture Documents
Paper-Ii - Ame Oct 2012
Paper-Ii - Ame Oct 2012
E
PAPER II
1. Titanium is heat treated for following purpose
a) Thermal hardening to improve strength
b) Annealing offer hot working and cold working to provide maximum
ductility for subsequent cold working
c) Both a & b********
d) None
2. The normal soldering technique of A1 is
a) Similar to that of the other material*******
b) Differ to control the expansion and contraction of metal********
c) Differ to the extent a low heat input is required
d) Both b & c is correct
3. Flux is used in welding of N-alloy is for
a) better penetration
b) fid to oxidation********
c) for better fusion
d) slow down the flow of molten metal
4. Flux used in silver soldering is
a) Zinc chloride*******
b) Orthophaspheric acid
c) Sulphuric acid
d) All are correct
5. Rust is steel is removed by
a) Wire brush
b) Emery paper
c) Controlled sand blasting
d) All are correct*********
6. Barcol tester is used on
a) harder material
b) softer material******
c) all type of material
d) none
7. I-beam is produced by
a) Extruding *******
b) Forging
c) Csting
d) Hot rolling*********
8. Which one is stable wrought alloy
a) piston
b) cylinder head
c) crankshaft
d) alclad*********
9. The load per unit square inch at which material breaks
a) ultimate tensile strength******
b) yield point
10. Ultrasonic testing is used to check
a) fatigue crack
b) disbond
c) weld and inclusion on cast
d) all are correct********
11.Which statement is correct regarding sensitivity of the x-rays
a) The darkness of radiograph does not depend on the radiation penetrating in the
cylinder
b) Thicker the specimen, lighter the image******
c) Thicker the specimen, darker the image
12.Muntz metal is used
a) to make oil and hydraulic filling
b) to make nut and bolts for used in salty atmosphere********
c) to make nut and bolts which are not affected by fresh water
d) none
13. Most N-weldable material is
a) 2 S
b) 17 S
c) 52 S*******
d) 53 S
14. A punch made of tool steel is heat treated to
a) heat to cherry red colour**********
b) as in (a) and dipped in sand
c) heat to dazzling white
d) as in (b) and heat to purple colour
15. Binary no. 11.75 digital form is
a) 1011.11*******
b) 1101.11
c) 1011.10
d) 1111.01
16. Figure indicate
a) X-OR
b) X-NOR**********
c) CMOS-OR
d) X-NAND gate
17. Choose correct no used in hexadecimal
a) 2
b) 8
c) 10
d) 16***********
18. A modern digital computer use
a) Octal No
b) He
c) Binary No.********
d) None
19. Computer perform only the calculation
a) Simple
b) Complex
c) Problem which split into no. of logic step********
d) None
20. High discharge tester is used to check the
a) voltage of battery in normal operating condition
b) efficiency of condenser
c) generator output
d) voltage of battery to find its charge condition and if recharging is
required********
21. Electrical power and energy is expressed in terms of
a) Kilo-watt and kilo-watt hour respectively*********
b) Watt and joule respectively
c) Watt and watt-hour respectively
d) Watt and newton
22. A 3-8 winding rotate with 1800 rpm in magnetic field having 8 poles, its frequency
will be
23. A wire is connected to constant voltage supply while its length and radius is doubled
a) electric field is half
b) electric field is double********
c) heat is unchanged
d) electric field remain same
c) Gyrometer********
d) Both a & b
25. AC induction motor is used in place of d.c. motor
a) because of less weight
b) it requires less maintenance
c) less expensive than dc motor
d) do not use brush and commutator*******
26. In lead acid battery, temperature correction factor is necessary
a) for temperature above/below 80F**********
b) for temperature above /below 100F
c) for temperature above/below 120F
d) no correction is made
27. A generator relay having silver and copper contact point
a) to provide greater bearing surface and low resistant*********
b) copper make contact and Ag break contact and increase life
c) for the purpose of spark
d) to prevent arcing
28. When a new Ni-cd battery is installed, its cell seal is opened and pour electrolyte to
ensure the full charge battery
a) no charge is required
b) charge is given and boost up and (A)
c) as in (b) and suddenly installed in a/c service
d) as in (b) and after two hours, check the electrolyte and installed in service*******
29. Purpose of flaps and slots is
a) Increase or decrease the speed of a/c
b) To decrease landing and take off speed, in turn reduce runway length*********
c) As in (a) and reduce fuel consumption
d) As in (b) and used in high speed aircraft only
30. When angle of attack increase
a) lift decrease
b) lift increase
31. J-bolt is classified according to
a) outside diameter
b) outside diameter and wall thickness******
c) inside diameter
d) inside diameter and wall thickness
32. If countersunk is not possible to use on thin sheet to get flush surface, then we can use
a) round head rivet
b) brazier head rivet******
b) Thermocouple
c) Both**********
41. Which statement is correct
a) Output is energized when all the inputs energized in AND gate**
b) Output is energized when more than one input energized in OR gate
c) Both (a) & (b)
d) None
42. Pure semiconductor shows
a) infinite resistance at 0c
b) increase in resistance with increase in temperature
c) decrease in resistance with increase in temperature**
d) none
43. i. Dos is
a) programme
b) processing unit
c) disk operating system**
d) all
ii. At starting date is given on
a) hard disk
b) ROM
c) RAM**
d) Floppy
44. Software is a
a) programme**
b) language
c) operating system
d) all
45. Most latest device used in computer
a) microprocessor **
b) diode
c) transistor
d) chips
46. In straight conductor, the resistance do not depends upon
a) temperature
b) length
c) material
d) shape of cross section***
47. Electrical bonding and shielding is used to
a) avoid accumulation of static charge
b) give stability in radio reception
c)
=
b) 2 & 3
d)
80. In a venire micrometer, 9 parts of the main scale is devided into 10 parts of the
vernier scale the main scale has the graduation of 1mm. The least count is
a) 0.01 mm
b) 0.020 mm
c) 0.009 mm***
d) 0.001
81. Mark the correct statement
a) E-glass is electrical glass
b) Has low strength and high wt
c) E- glass is borosilicate glass
d) All***
82. In aramid
a) Kevlar has 4 times the strength of aluminum
b) White colour****
c) All
d) None
83. Boron fibres are
a) made by depositing tungsten on boron
b) boron on tungusten deposite***
ANSWERS:
1. C
2. A, B
3. B
4. A
5. D
6. B
7. A, D
8. D
9. A
10. D
11. B
12. B
13. C
14. A
15. A
16. B
17. D
18. C
19. C
20. D
21. A
22. -
23. B
24. C
25. D
26. A
27. A
28. D
29. B
30.
31. B
32. B, C
33. A
34. A, C
35. A
36. D
37. C
38. C
39. A
40. B, C
41. A
42. C
43. C, C
44. A
45. A
46. D
47. C
48. B
49. A
50. C
51. D
52. A
53. A
54. A
55. A
56. A
57. A
58. B, C
59. D
60. D
61. A
62. B
63. A, D
64. B, D
65. C
66. A, D
67. A
68. C
69. C
70. B
71. B
72. C
73.D
74. C
75. C
76. A
77. B
78. B
79. D
80. C
81. D
82. A
83. B
PAPER II
1. Generally speaking, ball grip length should be
a) one and one half times the thickness of the material through which they extend
b) equal to the thickness of the material through which they extend plus
approximately one diameter
b) ADS
c) Location of the datum
d) Control surface adjustment
3. Refer the figure, what will the ohmmeter read
figure
a) 20 ohm
b) 0 ohm
c) 40 ohm
4. The numbering system ALPPHT-88 is for
a) blind type lock bolt
a) 2.5 Mg
b) 1.2 Mn
c) 5.6 Zn
d) 2.5 Zn
7. Mark the correct statement
a) T4 solution heat treatment
b) T5 solution heat treatment
c) T6 solution heat treatment + artificially aged
d) Both a & c
8. Monel is____
a) heat treatable and non-treatable
b) non-heat treatable
c) magnetic
a) red
b) black
c) blue
d) yellow
14. Teflon nose is designed to meet the requirement of
a) higher operating temperature and pressure
b) highly resistant to vibration and fatigue
c) high operating strength
a) tap extractor
b) easy out screw extractor (for broken screw)
c) by drilling on the top of tap
d) none
19. If the rpm of the driver gear is 60, then the rpm of driven gear is
a) 120 rpm
b) 100 rpm
c) 60 rpm
d) 30 rpm
20. Identify the figure
a) bevel gear
b) helical gear
c) spur gear
d) worm gear
21. Identify the figure
a) glat drill
b) straight fluited drill
c) twist drill
d) none
22. Identify the figure
a) flared tublar
b) plateless fitting
c) head and stamp
d) imaged plumbing
23. Voltmeter is always connected
a) in series with the circuit
c) both a & b
d) none
30. Choose the correct statement regarding towing
a) a/c equip with tail wheel and towed generally from forward
a) Brilliant yellow green for defect and deep blue violet for sound
surface
b) Deep blue for defect and yellowish green for sound surface
c) Red for defect and white for sound surface
d) White for defect and red for sound surface
35. A transducer converts
a) electrical energy into mechanical energy
b) mechanical energy into electrical energy
c) chemical energy into electrical energy
b) longitudinal defect
c) transaction defect
d) all
37. De-magnetization is carried-out by
a) moving the part away from the alternating field of solenoid
b) deflecting the part to a magnetizing field continuously inversing in direction and
at the same time gradually decreasing the strength
c) passing the a.c. to the part and reduce the current to zero
b) electrode
c) electrolyte
d) tank
39. After tempering, the part is cooled in
a) hot water
b) eddy current
c) ultrasonic
41. The programmer step up the voltage in the ratio of 5:1 and secondary current is 0.20
amp, the primary ?????????
42. What is the descriptive of the annealing process of steel during and after it has been
annealed
a) Rapid cooling, high strength
b) Rapid cooling, low strength
a) shear load
b) tensile load
c) external load
d) all
44. The main control unit of computer in present is
a) VDU
b) CPU
c) Key board
d) Hard disk
45. While testing for magnetic testing, it was found non-magnetic, in nitric acid it was
found rapid action, greenish blue color, the material is
a) Ni-steel
b) 18-8 steel
c) monel
d) CRS
46. Analogue computer is
a) more correct than digital computer
c) 6
d) 9
49. Al-alloys can be heat treated
a) solution heat treatment
b) precipitation heat treatment
c) artificial aging indicated with W(T5)
d) both a & b
50. In NDT, satisfactory performance of magnetic particle inspection cannot be find in
a) Cd
b) Cu
c) Sn & Zn
d) None
51. The transferring metal from one object to another by chemical and coating is done to
protect the base metal from
a) Corrosion
b) Wear
c) Increase the dimension to protect the base metal against chemical reaction
d) all
52. Improve tensile strength, ductility and sleck (shock) resistance of Mg-alloy casting
are normally
a) Case hardened
c) 11011
d) 11101
56. The magnitude of induced emf produced in a coil, when a magnet is inserted in it,
does not depend upon
a) no. of turns in coil
b) resistance of coil
c) magnetic moment of magnet (magnetic strength)
d) speed of rotation of magnet
57. Kewlar composite material has
a) a bright grey color
b) uncommon
c) same as plastic matrix with fibre reinforcement
d) none
60. A transfer is___
a) TIG welding
b) MIG welding
62. The tool shown is
a) flap wrench
b) die stock
c) none
63. Which Booleans algebra is not true
a) A+B=B+A
b) A.0=0
c) A.A=0
d) A.1=0
b) NAND
c) OR
d) XOR
65.
The weld is
a) V butt weld
b) U butt weld
c) Beveled butt weld
d) T butt weld
66. Brinnel hardness tester is used for
a) soft material
b) steel
c) hard material
d) all
68. The ATA-100 specification no. for hydraulic, pneumatic, stabilizers and engine is
a) 55,36,29,77
b) 36,29,55,77
c) 29,36,55,77
d) 29,36,77,55
69. The missing edge or planes are shown by
a) dotted line
b) dashed line
c) hidden line
d) all
70. In some large a/c, in the side of main L/G strut, there is a hydraulic jack
a) to jack-up the a/c when one wheel is to be raised
71. The precision measuring tool, that is used for measuring crankshaft and main bearing
journal for out of roundness and wear is
a) dial gage
b) depth gage
c) micrometer caliper
d) vemier caliper
72. The dimensional inspection of a bearing in rocker arm can be accomplished by
a) depth gage and micrometer
ANSWERS:
1. C
2. B
3. C
4. B
5. A
6. A, C
7. D
8. B, D
9. D
10. B
11. A
12. A
13. A
14. D
15. A
16. A
17. B
18. A
19. A
20. B
21. C
22. B
23. B
24. C
25. A, D
26. B
27. A
28. C, D
29. C
30. B, C
31. C
32. ??
33. D
34. A
35. D
36. B
37. D
38. B, C
39. C
40. B
41. A
42. C
43. A
44. B
45. A
46. B
47. B
48. C
49. D
50. D
51. D
52. B
53. A
54. A
55. C
56. B
57. B
58. B, C
59. B
60. A
61. A
62. A
63. D
64. B
65. B
66. A
67. A
68. C
69. C
70. A, B
71. A, C
72. B
73. A
PAPER II
1. Flareless tube fitting consists of following parts
a) body, sleeve, flared tube and nut
b) body, sleeve and nut****
c) sleeve, nut and end terminals
d) sleeve, shoulder, beaded tube, and nut
2. Color of fire extinguisher fluid line is
a) yellow
b) brown or yellow
c) red**
d) maroon**
3. If two end terminals of PN junction is connected through a conducting wire than
a) a steady current flows from P-type to n-type material
b) no steady current flows from wire**
c) steady current flows from n-type material to p-type material through wire
d) any one of the above
4. A prime limitation with directly heated cathode is due to
a) low frequency
b) voltage fluctuation**
c) high frequency
d) phase
5. Bottle jack is used for
a) removing a wheel or complete single wheel assembly form one landing gear
b) only removing brake unit
c) only removing single unit***
d) all of the above****
6. During jacking the a/c outside the hangar
a) face the a/c tail to wing
b) can be jacked in any direction
c) surface should be hard and level*****
d) none
7. Mark the correct statement
a) straight flute remmer has a tendency to reduce chatter
b) buttoning reamer is tapped at bottom for starting aid
c) spiral flute reamer is tapped at bottom for aid in starting****
d) none
a)
b)
c)
d)
16. What should be the first step of the procedure in sketching an a/c wing skin repair
a) draw heavy guidelines
b) lay out the repairs***
c) block in the views*****
d) draw extension lines
17. A cathode (electron emitter) used in thermionic emission must have following
characteristics
a) high mech. point
b) high mech. strength
c) low work function
d) all above are correct*****
18. When bolts and rivets are used to joint the metal sheets, then both should be protected
from corrosion by
a) applying grease on both
b) by plating bolt and rivets*****
c) by painting bolt and rivets
d) they must be placed separately approximately, 2-times than the thickness of the
metal being joined
19. Denting in metal tube is acceptable if
a) not more than 10% of tune diameter
b) less than 20% of tube dia******
c) not more than 40% of tube dia
d) must be rejected if dent occurs
20. Primary control surfaces are
a) elevator rudder, aileron and leading edge flap
b) elevator, rudder, aileron and trailing edge flap
c) elevator, slots, spoiler and flaps
d) elevator, rudder and aileron****
21. Crazing in plastics occurs due to
a) manganese
b) phosphorus
c) silicon
d) sulphur****
22. Mark the correct statement
a) single needle pointed end scriber should be sharp and surface should be checked
for flatness with straight edge
b) single needle pointed end scriber should be sharp*****
c) 90 bend, scriber should not be sued as far as possible*****
d) all of the above
23. If a line is divided into 25 division so that 25 divisions of this line is equal to 24
division of another line so that minimum distance that can be measured is equal to
difference between the value of each division . it is the principle of
a) DTI
b) Micrometer
c) Vernier scale*****
d) Rules
24. Magnesium surface should be cleared with
a) stiff-hog bristle****
b) steel wool
c) crocus cloth
d) steel wire brush
25. Which of the following frequency is used for space propagation
a) 2 KHZ
b) 30 MHZ and above
c) upto 30 MHZ
d) 20 KHZ 200 MHZ*****
26. Fusible metals are used for tube bending has
a) low melting point and ductile******
b) hard and high melting point
c) should expand on solidifying
d) both a & b are correct
27. For very accurate readings during such calibrations the thimble may be viewed under
a microscope of
a) low magnification*****
b) medium magnification
c) high magnification
28. When hydraulic fluid lines and electrical line is passing through same portion of a/c,
then
a) Hoses should be fitted above the wires and should be secured to a/c structure
b) Electrical wire should be fitted above and to secure to a/c structure *****
c) A minimum of 4-distance should be maintained between two and any of two can
be unstable above
d) Either of wire can be installed above and a minimum of
29. In straight and level flight
a) lift=drag and thrust=weight
b) lift=thrust and drag=weight
c) lift=weight and drag=thrust******
d) none of the above
30. Black smith anvil is made by
a) machining
b) forging *****
c) extrusion
d) both a & b
31. Crevice corrosion caused due to
a) metal and non-metal comes in contact and oil is present between them
b) contact between metal and non metal******
c) plastic and metal contact*****
d) due to improper heat treatment
32. Modern computer consists of
a) hard-ware
b) soft ware
c) CPU, input/output*****
d) ROM, software and logic gates
33. Fretting corrosion occurs due to
a) Stationary parts are subjected to relative motion to each other***
b) Direct contact with caustic liquid and battery fumes
c) Improper heat treatment
d) Combination of tensile stress and corrosive environment
34. Amount of electron that can be stored on capacitor is proportional to
electrolyte
a) both plate area and distance between them
b) plate area and does not depend upon distance between them
c) plate area and inversely proportional to distance*****
d) distance between plates and inversely proportional to area
35. Resistance for a straight conductor does not depends upon
a) length
b) shape of cross section******
c) temperature
d) material
36. Working voltage of capacitor should be
a) atleast 20% higher than applied
b) atleast 50% higher than applied****
c) equal to applied voltage
d) less than 50% than applied voltage
37. Mark the correct statement
a) Philips screw driver has sharp end*****
b) Reed and prince screw driver has blunt end******
c) Reed and prince screw has larger area in center
d) Both are interchangeable
38. For high speed a/c, it has wing
a) thicker than low speed a/c
61. A micro switch will close or open a circuit with the movement of
a) 1 or more
c) both a & b
16
b) 1 or less******
16
d) none
ANSWERS:
1. B
2. C, D
3. B
4. B
5. C, D
6. C
7. C
8. A
9. C
10. B
11. B
12. B
13. C
14. B
15. C, D
16. B, C
17. D
18. B
19. B
20. D
21. D
22. B, D
23. C
24. A
25. D
26. A
27. A
28. B
29. C
30. B
31. B, C
32. C
33. A
34. A, C
35. B
36. B
37. E
38. B
39. B
40. C
41. C
42. B
43. D
44. A, B
45. D
46. C
47. A
48. D
49. A
50. B
51. C
52. A
53. A
54. ??
55. A, B
56. A
57. A
58. A
59. C
60. A
61. B
62. B
PAPER II
1. Clevis pin used
a) with head up position
b) as in (a) & washer must be applied under it***
2. Peel ply means__
a) prevent excess resists
b) remove, after cure
c) prevent vaccum bagging from stricking to the paint
d) all are correct****
3. In magnetic and non-magnetic material, coating thickness of ferrous and non-ferrous
alloy should be measured by
a) eddy current*****
b) magnetic particle test
c) micrometer caliper
d) all
4. Which takes primary load
a) fibre*****
b) metrix
c) both a & b
d) none
5. Which takes in part of transferred load
a) fibre
b) metrix
c) both a & b
d) none
6. In case hardening, nitriding process
a) with the part this heated ammonia gas is circulated within the furnace
chamber****
7. T- section, Z-section and angles are formed by
a) rolling
b) forging
c) extrusion***
d) all
8. Hole must be inspected for cracks or burrs
a) before reaming
b) after reaming
c) before and after reaming***
d) none
9. When two surfaces fit tightly together, but can move relatively to one another
a) fretting corrosion*****
b) intergranular corrosion
10. Unit of magnetic flux is
a) webre****
b) Newton meter
c) Both a & b
d) None
11. Which statement is correct
a) welded joint of thick material can not be inspected by ultrasonic test
b) thin sheet metal welds are more satisfactorily checked by X-rays****
12. P.N. junction in transistor has
a) forward bias
b) reverse bias****
13. Which fibre has higher compressive strength
a) carbon fibre****
b) aramin
14. Mark The correct statement
a) Hot water quenching minimizes distortion and alleviates crack****
15. Galvanometer is transferred in ammeter
a) By connecting low resistance in series to the galvanometer
b) By connecting high resistance in series to the galvanometer
c) By connecting low resistance in parallel to increase range*****
d) By connecting high resistance in parallel to increase range
16. Mark the correct statement
a) Off set screw drivers are constructed with both ends bent at 90 to the shank****
b) Rachet screw driver is used for heavy duty
c) Reed and prince screw driver is interchangeable with Philips so
d) All are correct
17. Where high temperature is used for brazing
a) for high power solder
b) special type of flux is used
c) not used for brazing****
d) none
18. High heat of Al-sheet from fire causes
a) Increase ductility
b) Decrease ductility
c) Increase resistance*****
d) None (increase, conductance)*****
ANSWERS:
1. B
2. D
3. A
4. A
5. B
6. -
7. C
8. C
9. A
10. A
11. B
12. B
13. A
14. A
15. C
16. A
17. C
18. C, D
19. A
20. C
21. B
22. A
23. D
24. B, C
25. B
JUNE
1. In 7075-0 indicates
a) annealed*******
b) strain hardened
c) solution HT
d) none
2. One r is dash on bolt head indicates
a) CRS bolt
b) NAS close tolerance bolt
c) AN standard bolt******
d) None
3. The line used for reference of parts is
a) reference line
b) hidden line
c) phantom line*******
d) black line
4. The colour of 6053 Al-alloy is
a) red
b) black******
c) grey
d) white
5. Lock bolt, which indicates flat head is
a) ALPP
b) ALPB
c) ACST
d) ALSF******
6. In flexible hoses slack is given
a) 2 to 3% of total length
b) 5 to 8 % of total length*******
c) 3 to 9% of total length
d) 10% of total length
7. When tightening of nut is precious, which tool is used
a) allen wrench
b) torque wrench*******
c) spanner wrench
d) combination wrench
a)
b)
c)
d)
5056-T
2117-T
2024-T******
5056-W
9. Al-alloy is not heat treated properly to have uniform grain boundaries it has
a) stress corrosion
b) galvanic corrosion
c) intergranular corrosion*******
d) fretting corrosion
10. Which one is unpaired
a) battery accumulator
b) diode NRV
c) AC generator vortex generator*******
d) EMF MMF
11. Which is used to transfer rivet size from template to new sheet is
a) centre punch
b) pin punch
c) alignment punch
d) transfer punch********
12. A side clearance between piston ring and cylinder wall is measured by
a) telescopic gauge
b) thickness gauge*******
c) micrometer
d) plug gauge
13. When base circuit is open at R, then
a) bulb can not be turned off
b) bulb can be turned off******
c) bulb can not be effected
d) high current will flow in circuit
14. The resistance of conductor depends on
a) temperature
b) length and material
c) cross-sectional area
d) all*******
15. In on inductive circuit
a) current lags behind voltage by 90******
b) current leads behind voltage by 90
c) Current and voltage are in phase
d) None
16. In magnetic particle inspection, nickel plating does not give indication of
a)
b)
c)
d)
crack
discontinuities********
corrosion
none
17. In dye penetrant inspection, the defects under which light appears
a) black
b) green
c) red ******
d) all
18. Which is unpaired
a) dye penetrant capillary acceptance
b) ultrasonic test peizo electricity******
c) eddy current test current acceptance
d) magnetic test skin test
19. Dye penetrant inspection is applicable to
a) ferrous alloys only
b) plastic and non metal
c) non ferrous alloys metal
d) all******
20. In ultrasonic test, when mechanical stress vibration is applied to crystal quartz then
these are
a) electrical energy and voltage are produced
b) more vibrations are produced
c) as in (A) and varies with the thickness of crystal******
d) none
21. Form of corrosion which occurs between metal and non metal is
a) filliform corrosion
b) crevice corrosion********
c) exfoliation corrosion
d) fretting corrosion
22. Normalizing is applicable to
a) cu-alloys
b) Al-alloys
c) Ferrous alloy only*******
d) Both a & b
d) Si
B
0
1
0
1
Y
0
1
1
0
OR-gate
X OR gate******
AND-gate
NAND gate
39. Mg is ________
a) Susceptible to corrosion
c) all
d) none
d) none
56. In cable strand, the wires are performed to provide
a) corrosion resistance
b) flexibility
c) prevents from ravalling
d) both a & b*******
OCT
1. The piston engine works on
a) Boyles law
b) Brayton cycle
c) Charles law & otto cycle
d) Both a & c*****
2. The mechanical efficiency of piston engine is determined by
a) engine speed
b) fuel used
c) mean effective pressure******
d) mixture ratio (throttle setting)
3. The main alloying element is 7075 Al-alloy is
a) Cu
b) Mn
c) Zn******
d) Si
4. The tubes are sized by
a) inside diameter in increment of 1/16
b) inside diameter in increment of 1/32
c) out side diameter in increment of 1/16*******
d) out side diameter in increment of 1/32
5. Flared tube fittings used in a/c are made of
a) Al-alloy
b) Cu
c) Steel
d) All are correct*******
6. Muntz metal consists of
a) 60% of Cu and 40% of Zn
b) 60% of Zn and 40% of Cu
c) as in (a) and basically brass******
d) as in (b) and basically brass
7. Steel has fine grain structure, when
a) when heated above the critical temperature****
b) when heated below the critical temperature
8. The soldering of Al-alloys differs from other metals due to
a)
b)
c)
d)
d) ac & dc*****
a)
b)
c)
d)
abrasive paper
fine buffing cloth on buffing wheel********
wire brush
all
b) difference of temperature
c) difference of grade of fuel used******
d) difference in mass of fuel
32. A device which gives lateral control and is mounted at the opposite surface of wing
a) spoiler ******
b) vertex generator
c) tab
d) flap
33. The presence of water can be detected by
a) USI
b) DPI
c) Endoscope
d) Radiography******
34. Aircraft bolts are generally manufactured with a
a) Class 1 fit for the threads
b) Class 2 fit for the threads
c) Class 3 fit for the threads*****
d) Class 4 fit for the threads
35. The hose of l00LL AVGAS dispenser is
a) red
b) blue******
c) black
d) green
36. Which is low energy logic circuit
a) TTL
b) ECL**********
c) Both a & b
d) None
ANSWERS: JUNE 1. A
2. C
3. C
4. B
5. D
6. B
7. B
8. C
9. C
10. C
11. D
12. B
13. B
14. D
15. A
16. B
17. C
18. B
19. D
20. C
21. B
22. C
23. B
24. B
25. A
26. B
27. B
28. B
29. A
30. D
31. C
32. D
33. A, C
34. B
35. C
36. A
37. B
38. B
39. D
40. A
41. D
42. A
43. D
44. C
45. A
46. D
47. A
48. A, D
49. B
50. B
51. A
52. A
53. C
54. C
55. C
56. D
ANSWERS: OCT
1. A, D
2. C
3. C
4. C
5. D
6. C
7. A
8. B
9. D
10. B, D
11. C
12. B
13. C
14. A
15. B
16. B
17. A, D
18. D
19. A, B
20.D
21. A
22. D
23. B
24. A
25. B
26. D
27. A
28. C
29. A
30. D
31. C
32. A
33. D
34. C
35. B
36. B
PAPER II
1.Color code of 2024 Al-alloy tubing is
a) white
b) green
c) red******
d) black
2. Head marking of corrosion resistance steel (CRS) bolt is
a) raised dash (single)*****
b) raised ring/dash
c) recessed triangle
d) no head marking
3. Rivet of diameter is replaced by
a) two 1/16 diameter rivet
b) three 1/16 dia rivet
c) three 1/32 dia rivet
d) none four 1/16 dia rivet*****
4. Rivet can be removed by
a) center punch
b) prick punch
c) pin punch (drift punch)- drive or tapered punch***
d) alignment punch
5.
a)
b)
c)
d)
tin *****
zinc
titanium
all
b) assembly drawing********
c) installing drawing
d) none
18. Identify the bolt (CAIP-BL/2-3)
figure
a) 12 point ball
b) 12 point drilled bolt
c) 12 point extender washer bolt (cup washer locked)*****
d) 1 double haxagon head bolt******
19. Minimum bend radius of flexible hose depends upon
a) type of the material
b) size of the hose
c) working pressure
d) both a & c******
20. Regarding the plumbing of rigid tube, which is true
a) less dia tubing requires less distance support******
b) less dia tubing requires more distance support
c) large dia tubing required less distance support
d) large dia tubing requires more distance support
21. Double flaring provides
a) smoothness
b) more concentric
c) seals better
d) all*******
22. Combination of corrosion resistance steel (18-8 steel)
a) 8% Ni and 18% chromium*****
b) 18% Ni & 8% chromium
c) 29% chromium & 8% nickel
d) 8% chromium & 29% nickel
23. As per ATA-100 specification, the correct sequence of air conditioning, fuel,
navigation and oil system is
a) 21,28,34,79*****
b) 21,34,28,79
c) 31,34,52,80
d) 32,28,34,79
24. Find out the reading of metric micrometer
a) 5.46
b) 5.64
c) 0.564
c) 0.011
d) 0.100
40. (1010101)2 = (
)10
a) 110
b) 85******
c) 75
d) 95
c) V.l
d) all****
I angle projection
II angle projection
III angle projection*******
Sectional projection
50. Output is zero when input is 1 or both inputs are 1, the gate is
a) AND gate
b) NAND gate
c) NOR gate*****
d) OR gate
51. For given figure, which is correct
d) 1,0,0
A
a) 0,0,1
b) 1,0,1*****
c) 1,1,0
B
C
ANSWERS:
1. C
2. A
3. D
4. C
5. C
6. B
7. C
8. B
9. A
10. D
11. A, D
12. C
13. B
14. B
15. B
16. A
17. B
18. C, D
19. D
20. A
21. D
22. A
23. A
24. C
25. B
26. B
27. C
28. B
29. B
30. A
31. B
32. D
33. A, B
34. A
35. D
36. B
37. B
38. C
39. B
40. B
41. A
42. A
43. D
44. A
45. D
46. B
47. C
48. A,B,D
49. A,C
50. C
51. B
52. B
53. B
PAPER-II
1. Ohms Law does not holds for
a) diode
b) mercury
c) P-N emulsion
d) a & c both*****
2. Speed of motor increases, when load decreases, current decreases because of
a) frictional loss b/w motor moving parts
b) frictional loss b/w field winding and other parts
c) induced back emf increases******
d) none
3. During inspection after swaging if it is found that
a) shank dia is too large that means it is overswaged
b) shank dia is too small that means it is overswaged it should be rejected*******
c) shank dia too small it means underswaged
d) shank dia is too large it means underswaged and it should be rejected
4. Flab tab is
a) balance tab
b) trim tab
c) servo tab
d) none******
5. Geiger counter is used
a) to check the condition of a/c after heavy landing
b) to check the condition of a/c after flight through turbulence
c) to check penetration of a/c by ultraviolet rays
d) none*******
6. Lift depends on
a) wing area
b) wing shape
c) square of velocity and density of air
d) all of above******
7. Mark the correct statements
a) lateral leveling in heavy airplane is more critical*******
b) leveling lateral point always on longitudinal axis
c) leveling is always done in longitudinal axis
d) none
c) (64)10
d) none
ANSWERS:
1. D
2. C
3. B
4. D
5. D
6. D
7. A
8. C
9. D
10. A
11. A
12. D
13.D
14. D
15. A
16. B
17. A
18. A
19. C
20. D
21. B
22. D
23. B
24. B
25. D
26. A
27. C
28. A
29. B
30. D
31. B
32. B, C
33. B
34. A
35. A
36. D
37. D
38. D
39.D
40. C
41. C
42. A,B,C
43. C
44. C
45. D
46. A,B
47. B
48. B
49. D
50. C
51. -
52. C
53. D
54. C
55. D
56. B
57. D
58. A
JUNE
1. Color of the fire, protection fluid line is
a) red
b) brown ******
c) green
d) brown and orange
2. A/c bolts are manufactured with always
a) class 1 fit
b) class 2 fit
c) class 3 fit******
d) class 4 fit
3. Which of the following precision instrument is sued for tightening the nut on bolt with
proper torque is
a) socket wrench
b) torque wrench********
c) ratchet wrench
4. For repairing the oversize hole with sleeve, the hole must be drilled oversized by
a) 3/16
b) 1/32
c) 1/64 **** d) 3/64
5. 7 X 19 size of cable indicates
a) 7 wires of 19 strand
b) 7 strand of 19 wire******
c) 7 strand of 19 strand
d) none
6. Clevis bolt used in fork end of cable fitting
a) AN-CRS bolts********
b) NAS-CRS bolts
c)
d)
7. Intergranular corrosion is normally caused by
a) internal stresses
b) improper heat treatment*******
c) electrolyte
d) all of the above
8. Spilled electrolyte of lead-acid battery is neutralized by
a) ammonia
b) baking soda******
c) vinegar
d) both a & b********
9. What type of battery charger is recommended for final charging of a Ni-cad battery
a) constant current charger
b) constant voltage charger
c) both a & b
d) any one of the above
10. Corrosion product in magnesium is removed by
a) steel wire brush
b) carborundum abrasive
c) stiff hog bristle brush******
d) all of the above
11. Purpose of heat treatment of titanium is
a) thermal hardening to improve strength
b) annealing for subsequent working
c) relieve stresses
d) all of the above*****
12. The process capacity of a computer is determined by
a) MHZ
b) KHZ
c) RAM
d) frequently******
13. Hardness testing method of steel is
a) brinell or barcol
b) barcol or Rockwell
c) brinell or Rockwell********
d) none of the above
14. T6 indicates
a) artificially aged only
b) SHT and cold worked*******
c) SHT and their artificially aged
d) Solution heat treated
15. Mental fatigue of human is caused by
a) long period of duty
b) emotional stress
c) noise
d) all of the above******
16. A micro switch will open or close a circuit with the movement of
a) 1/16 or less*******
b) 1/16 or more
c) both
d) none
d) 7
26. End of steel bar sometimes painted in various colors and color combination as a mean
of identifying different grade of steel
a) solid colors identify the alloy and strips identify the carbon contents******
b) strips identify the alloy and solid colors identify the carbon content
c) both a & b
d) none of the above
27. Which gage is used to measure the backlash between gears
a) filler gage
b) screw pitch gage
c) fillet gage
d) DTI******
28. Accuracy of a finished screw thread is determined by
a) screw pitch gauge
b) ring thread gauge******
c) thread gauge
d) plug thread gauge
29. Highest size of drill is
a) No. 80 (0.0135)
b) 3/16 (0.1875)
c) 3.75mm (0.1475)
d) E (0.2500)******
30. Schematic diagrams are used mainly for
a) a/c maintenance and repair
b) trouble shooting******
c) installation of parts
d) all of the above
31. Mark the correct statement
a) turboprop engine requires lengthy runway than piston engine of same power
b) turbojet has more weight than piston engine of same power
c) turbofan required short runway as compare to turbojet********
d) all of the above
32. In towing the a/c (light) mark the correct statement
a) all tail wheel a/c towing towards backward
b) all nose wheel a/c towing towards backward
c) if steerable nose wheel a/c, locking scissors are set to full swivel position*******
d) none of the above
33. While starting the piston engine, which type of fire extinguisher is permitted
a) Water and water based agent
b) Co2, 516 capacity******
c) Dry chemical
d) CC14 (halon gas)
c) conduit
d) none
c) Green
d) Brown
ANSWERS:
1. B
2. C
3. B
4. C
5. B
6. A
7. B
8. B, D
9. A
10. C
11. D
12. D
13.C
14. B
15. D
16. A
17. A
18. B
19. A
20. A
21. C
22. B
23. C
24. A
25. D
26. A
27. D
28. B
29. D
30. B
31. C
32. C
33. B
34. A
35. A
36. -
37. A
38. C
39. A
40. A
41. A
42. B
43. A
44. -
45. B
46. B
47. B
48. A,E,F
49. A
50. A
51. A
52. B
53. A
54. D
PAPER-II
1. Red brass is used
a) for fuel and oil line fittings
b) as in (a) and also called bronze*****
c) as in (b) and has poor casting and forming quality
d) none
2. Nickel in steel increases
a) hardness
b) yield strength
c) elastic limit
d) all of the above*****
3. Geiger counter is used to
a) measure the radioactive contamination of a/c flying above stratosphere*****
b) check the condition of a/c after heavy landing
c) check the penetration of a/c by ultraviolet rays above statosphere
d) none of the above
4. Stalling angle critical angle of attack is the
a) maximum lift angle
b) minimum lift angle
c) as in (a) and at which separation of airflow takes from upper surface of
wing******
d) as in (b) and at which separation of airflow takes from lower surface of wing
5. Angle of ACME thread is
a) 45
b) 38
c) 12
d) 29******
17. Jo-bolt is
a) externally threaded two piece rivet
b) externally threaded three piece rivet
c) internally threaded three piece rivet*******
d) can replace general bolts in compression to their strength
18. Turn buckle is
a) for minor adjustment in cable length and cable tension
b) has matching left and right hand threads
c) has internally threaded ends and externally threaded end terminals
d) all of the above*********
19. Extrusion is used for making
a) channels
b) angle
c) T-section
d) All*****
20. Generator frequency depends on
a) no of poles
b) RPM
c) Both a & b********
d) None
21. For a battery to have high ampere hour capacity and high terminals voltage
a) low internal resistance******
b) high internal resistance
c) does not depend on internal resistance
d) none
22. Plug gage is used for
a) checking the internal dia of cylindrical shaft
b) checking the size of plug needed for blanking
c) checking the accuracy of holes
d) all of the above*******
23. A bolt should be installed
a) upward and downward
b) upward & forward*******
c) downward & forward
d) down ward & rearward
24. In a PN function diode, holes move from P-region to N-region because of
a) diffusion
b) pressure difference
c) higher concentration of holes in P-region******
d) electrons in N-region attracts holes from P-region
c) 265
d) 275******
57. When the time between soaking and quenching increases, then
a) hardness increases
b) softer the metal
c) re-precipitation takes place******
d) tensile strength increases
58. O-ring can be checked by
a) 4-times magnification
b) rolling the ring on a dowell and inner dia can be checked
c) rolling the ring on inspection cone & inner dia can be checked
d) all of the above******
59. Metalling is a process of
a) rolling pure Al-alloy on Al-alloy surface
b) Ni and cd plating on steel
c) By spraying Ni, Cr on steel with oxy-acetylene flame*******
d) All of the above
60. Which of the following are universal gates
a) NAND & AND
b) NOR & OR
c) NAND & NOR******
d) NONE
61. An 12 H5 indicates
a) dia 3/5 and head is not drilled
b) dia 6/8 and head is not drilled
c) dia 6/8 and head is drilled
d) dia 6/8 and shank & head is drilled******
62. Engine fires once in
a) one revolution of crankshaft
b) two revolution of crankshaft******
c) 360 revolution of crankshaft
d) none of the above
63. Mark the correct statement
a) On a/c with steerable nose wheel, the locking scissors are set to full swivel for
towing********
b) Tail wheel a/c should always be towed backward
c) Release all the hydraulic charge before towing
d) All of the above
64. Grub-screw is used for
a) locking threaded fasteners
b) by soldering it is locked
c) locked by peening
ANSWERS:
1. B
2. D
3. A
4. C
5. D
6. B
7. C
8. A, D
9. D
10. D
11. C
12. C
13. C
14. B
15. D
16. B
17. C
18. D
19. D
20. C
21. A
22. D
23. B
24. C
25. B
26. A
27. D
28. D
29. A
30. A
31. D
32. C
33. A
34. C
35. D
36. A
37. A
38. D
39. B
40. A
41. D
42. C
43. B
44. D
45. B,C
46. C
47. D
48. D
49.D
50. D
51. D
52. B
53. D
54. B
55. B
56. D
57. C
58. D
59. C
60. C
61. D
62. B
63. A
64. D
65. D
66. A
67. D
68. D
69. C
70. D
71. A
72. D
73. A
74. C
PAPER II (JUNE
1. For commercial annealing, cooling is done in
a) furnance
b) air
c) mica*****
d) both a & b
2. Cyniding of low carbon steel is quenched in
a) oil
b) brine
c) water
d) both a & b (all)*********
3. How long piece of steel is left in a furnace for soaking
a) for long enough to ensure a good even heat throughout
b) for 2 hours for per cubic inch of piece
c) one hour for each square inch of cross section area
d) both a & c*****
4. Seak often forms on the surface of the metal and dirt blocked on it, cleaning of seaks
and dirt from heat treated part is done by
a) steel wire brush
b) sand blasting
c) scap
d) all*******
5. In Rockwell hardness testing
a) softer the piece of metal, the deeper will be the impression under given load
b) the hardness is indicated on a dial gage graduated in the B & C scale
c) for non-ferrous metal, the steel ball should be used and hardness no. read on B
scale
d) all the above*********
6. Flame heating is done for
a) when hardness is required only for a limited depth of the material******
b) for small part
c) both a & b
d) none
7. The heat of the furnace can be controlled or regulated by
a) be watching the color of the furnace
b) barometer*******
c) thermo meter
d) all
c) threat diameter
d) all******
ANSWERS:
1. C
2. D
3. D
4. D
5. D
6. A
7. B
8. D
9. A
10. C
11. D
12. D
13. C
14. B
15. A
16. B
17. A
18. D
19. D
20. B, D
21. C
22. A
23. B
24. D
25. D
26. A
27. B
28. D
29. A
30. C
31. D
32. B
33. D
34. B
35. B, D
36. A
37. B
MARCH
1. In a spot welding a typical defect is
a) porosity
b) crack
c) irregular shape
d) both b & c******
2. In oxyacetelene welding while shutting off the flame
a) oxygen is shut out first
b) acytelene is shut off first******
c) both are shut off simultaneously
3. Oxyacetelene flame with equal volume of oxygen and acytelene gives the types of
flame as shown
a) carbonizing
b) oxidizing
c) neutral*****
d) there is no such flame
4. The silver solder metal melts at
a) 200-400 degree cent*******
b) 300-600 degree cent*******
c) 1000-2000 degree cent
d) 850-1200 degree cent
5. The core of reinforce polymer thermoplastic is filled as
a) metal
b) aluminium
c) fibre glass and plastic resin******
d) all of the above
6. Synthetic thermoplastic
a) when heated becomes soft
b) when heated becomes hard
c) when cools become hard
d) both a & c are correct*****
7. A crack may be repaired by
a) out welding******
b) spot welding
c) lap welding
8. In dye penetrant test the indication shown indicates
a) porosity*****
b) tight crack
************
25. In four digit N-alloy index system, no-2024, the first digit indicates_____
a) the % of Al-added
b) the different alloy in this group
c) alloy group
d) copper is the major alloying element*****
26. Why it is considered good practice to normalize a part after welding
a) to relieve internal stresses developed within base metal*****
b) to introduce a slight amount of carbon to improve the surface hardness of the weld
c) to remove the surface scales formed during welding
d) all are correct
27. Select the characteristics of a good gas weld
a) the depth of penetration shall be sufficient to ensure fusion of filler rod
b) the height of weld healed should be above base metal
c) the weld should taper off smoothly into base metal******
d) these should be no oxide on the weld
28. Indicates single butt weld
Figure
a)
b)
c)
d)
29. Which tool can be used to measure the alignment of a rotor shaft or the place of
rotation of disk
a) dial indicator (DTI)*******
b) shaft gage
c) protector
d) all
30. The measurement reading on vernier scale
a) 1.411
b) 1.436
c) 1.700
d) 1.456
d) 110110
ANSWERS:
1. D
2. B
3. C
4. A, B
5. C
6. D
7. A
8. A
9. B
10. B
11. A
12. B,D
13. A
14. A
15. D
16. C
17. C
18. A
19. -
20.
21. C
22. C
23. D
24. C
25. D
26. A
27. C
28. D
29. A
30.
31. B
32. A
33. B
34. -
35.C
36. A
37. B
38. A
39. B
40. B
41. C
42. B
43. C
44. -
45. B
46. B
47. D
48. B,C,D
49. D
50. A
51. A,B
52. A
53. D
54. D
55. C
56. C
57. A
58. B
59. C
60. B
61. C
62. A
63. B
64. C
PAPER II (JUNE
1. After cyaniding quenching is done in
a) brine
b) water
c) oil
d) both a & c******
2. To stop solder from flowing normally
a) clay is used****
b) a flux is used
3. Hard soldering (silver soldering is low temperature brazing)
a) is done at low temperature brazing
b) produces strength equal to parent metal
c) both a & b******
d) none
4. Flame is used to heat metal during heat treatment for
a) small parts
b) where furnace is not available
c) heat treatment requirement is not very exacting
d) large parts and where a particular area is to be heated*******
5. Mark the correct statement
a) detection welds in thicker material UFD is best
b) X-ray best for welds in sheets
c) Both a & b
d) All*******
6. When flying along magnetic equator, dip will be
a) increased
b) remain unchanged*******
c) decreased
d) depend upon direction of flight
7. Identification of alloy is made of by
a) alloy identified by color, content by stripes******
b) alloy by stripes and content by color
8. Heat treated parts having bake-dirt and scale can be cleaned
a) wire brush
b) scraping
c) sand blasting******
d) none
34. To measure the thickness of the hollow tubular member normally done by
a) distructive method
b) eddy current method
c) ultrasonic method*******
d) none
35. a combination set is used as
a) dipth, gauge, tri-square, scriber
b) protractor, scriber, trisquare
c) center head, protractor, scriber******
d) none
36. Mark the correct statement regarding the hardness tester
a) brinell system uses diamond point
b) vikers uses round ball
c) above are correct
d) none********
37. In nickel cadmium battery
a) during discharging, the current flows the negative pole to positive plate and
oxygen atoms are driven out from the positive plate
b) electrical leakage is measured by millimeter between cell and casting
c) both a & b******
38. Hydrogen is given off during
a) all stages of LAB servicing
b) over charging of Ni-cd batt.******
c) both a & b
d) none
39. Dies are used to cut
a) internal threads of a nut
b) external threads of a nut
ANSWERS:
1. D
2. A
3. C
4. D
5. D
6. B
7. A
8. C
9. D
10. A
11. C
12. A
13.D
14. D
15. A
16. A
17. B
18. A
19. D
20. C
21. C
22. A
23. A
24. D
25. B
26. D
27. B
28. B
29. D
30. A
31. A
32. D
33. D
34. C
35. C
36. D
37. C
38. B
39.
PAPER II (OCT
1. In a capacitor
a) capacity depends on separation of plates and measured in farade
b) capacity depends on area of plates and measured in farade
c) capacity depends on nature of dielectric material
d) all******
2. Relation between volt, ampere and weber is given by
a) amp/volt = weber
b) amp X volt = weber
c) volt / amp = weber
d) none*****
3. Which statement is correct relating to swaging
a) if the diameter of fitting is too large, it has been over swaged
b) if the diameter of fitting is too small, it has been under swaged
c) if the diameter of fitting is too small, it has been over swaged and cable fitting
must be rejected***************
d) none
4. Mooring is the process in which
a) head of the a/c is in prevailing wind whenever possible
b) choke all wheels fore and aft
c) tie down the point on aircraft
d) all****
5. How will you convert a galvanometer in voltmeter
a) by connecting a high resistance in series with galvanometer
6. What is the work of catalyst
a) as curing agent***
b) as hardener
c) mixed with resin
d) all are correct
7. Nomex is a
a) honey comb material***
b) reinforced fibre
c) metrix material
d) none
8. The properties of composite material is
a) do not corrode
b) stress, fatigue resistant
c) it reduce wear
d) all***
9. Zener diode
a) has high forward voltage rating
b) has negative resistance***
c) has a sharp breakdown of low reverse voltage
d) used as amplifier
10. In a dye penetrant test before applying developer, what shall be done
a) dye should be completely flushed out
b) only excessive dye should be removed
c) the rinsing operation is completely carried out
d) both b & c are correct***
11.Which is the correct statement regarding heat treatment of Al-alloy
a) longer soaking time and lower cooling rate result in greater softening*******
b) longer soaking time and higher cooling rate result in greater softening
c) soaking time should be minimum
d) none
12. If a magnet is dropped through a current carrying coil, it will fall with
a) uniform acceleration equal to g
b) uniform acceleration less than g***
c) non-uniform acceleration more than g
d) non-uniform acceleration less than g****
13. Type of heat treatment of component depends on
a) proper used
b) composition of alloying element
c) cold work is done
d) all*****
14. In annealing, greater softening can be achieved, if
a) cooling rate is very low and it is cold in furnace
b) heating just above the upper critical point
c) both *******
d) none
15. Transfer metal from one object to another by chemical and electrical means is done to
a) protect base metal against corrosion and wear
b) increase the dimension of a part
c) protect base metal against reaction
d) all********
16. The symbol shows
a) lead & Zn******
b) Mg. alloy
c) Cu-alloy
d) Fiber
b
V=0
a)
b)
c)
d)
1/3 from a to b
2/3 from a to b
1/3 from b to a
zero******
or
b) condenser
c) resistor
d) none
24. Corrosion on Al-alloy is visible in the form of
a) powdery form******
b) grey spot
c) pitting******
d) shining spark around the spot********
25. The hook spanner is used for
a) round nut having slot at internal******
b) square nut having slot at internal
c) hexagonal nut having slot at internal
d) all
26. Aviation snips are used for cutting
a) steel sheets
b) Al-sheets (heat treated)*****
c) Hard material
d) Soft material
27. The sensitivity of voltmeter is expressed in
a) Ohm
b) Watt
c) Emf
d) ampere1(ohm/volt)****
28. In inspection of bolt holes for pits and cracks is carried out
a) before starting reaming
b) after finishing reaming
c) before and after starting reaming*****
d) done
29. In coolers or radiators where operating temperature is high soldering is not done but
a) soldering can be done with approved flux
b) inert gas welding******
c) seam welding
d) spot welding
30. The function of flux in brazing operation is to
a) minimize oxidation*****
b) to break the surface tension of filling material
c) to flow filler material all round
31. Cracks in thick material welding can be checked by
a) eddy current
b) dye penetrant
c) ultrasound*******
32. Heat, treatment of N-alloy is carried out by
a) solution heat treatment
b) solution and precipitation HT********
c) age hardening
d) all
33. To charge the fire in case of only one tire, the jack should be used
a) to just clear the tire from ground
b) hydraulic jack (single base jack)
c) chocks used with remaining wheel
d) all are correct********
34. Mark the correct statement
a) The diametrical pitch and pitch diameter in a spur gear are same
b) If the dia. Pitch (DP) is given, you can find out the addendum*******
c) If we divide DP by PD, we can get size of teeth
d) If the DP is given, you can not find out the addendum
35. Kevlar is
a) white gliming cloth
b) 4-times more tensile strength than Al*******
36. A charge is moving along magnetic lines of force
a) if force will always act
b) no force will act*****
c) may act or may not act
d) none
37. With prepregs
a) manual application not required
b) has to be kept in freezer
c) both a & b*****
d) none
38. Weld decay can be prevented by
a) presence of titanium & nycheum
b) quick heating
c) both a & b*****
d) low temperature
QUESTIONS:
1. When it is necessary to use electrical connectors where they may be exposed to
moisture
Use a special type of moisture proof connector.
2. When joining electrical connectors they should be connected by
Hand only.
3. It is best to set the voltage regulator
When engine is warmed up.
4. High tension ignition wires are checked for current leakage with
Hardness tester
5. The wheat stone bridge utilize in a particular type of oil temperature gauge. It is an
electrical device for measurement of electrical resistances and in this instance the
resistance of wire bridge
Increase with rise in oil temperature
6. The use of small bundles of wire in a/c electrical system is desirable due to
Better flexibility
7. The Al cable must be numbers smaller than the copper cable
As the size no. get smaller, the cable itself is larger
8. The purpose of special washers on electrical terminals is
To better contact and locking purpose
9. When electrical cables or bundles are exposed to high temp
The size of the cable or bundle will increase
10. The material used is bounding the a/c should be
The same material as the bounded surfaces.
11. If the generator output were fluctuating, how would you place a resistor in the line to
settle out the fluctuations
In series with the generator
12. In most aircraft, lighting circuits are
In parallel to each other
13. As the temperature of a wire increases, the current carrying capacity
Decreases.
42. Junction boxes should be mounted with the open side facing downward, this
arrangement permits
Loose metallic objects, such as washers, bolts etc to fall out of the box and
prevent possible short circuits
43. An arcing fault between an electric cable and a metallic flammable, fluid line may
puncture, the line and result in a serious fire, when separation is impracticable, the
electrical cable should
Be places over flammable fluid line and securely clamped to the structure
44. Junction boxes should be proved with
Adequate drain holes
45. One of the most common used of rheostats is to vary the
Intensity of the tight throughout the aeroplane
46. Wheat stone bridge
When bridge is balanced, current will zero
47. After annealing, component is cooled in
Furnace itself and s/w off the heating source
ANSWERS:
1. D
2. D
3. C
4. D
5.
6. A
7. A
8. D
9. B
10. D
11. A
12. B,D
13. D
14. C
15. D
16. A
17. C
18. A
19. D
20.D
21. C
22. A
23. A
24. A,C,D
25. A
26. A,B
27. D
28. C
29. B
30. A
31. C
32. B
33. A,D
34. B
35. B
36. B
37. C
38. C
39. C
40. D
41. B
length
universal head**
brazier head
round head
any one of the above
9. In an alto meter if there is absence of barometer is pressure, the pitot line is checked
by:
a) vacuum chamber
b) micrometer**
10. The given figure indicates:
a) shake proof washer
b) internal star washer
c) both a & b**
d) none of these
11. In pitot static system the static vent to of the flat plate tube any where in the a/c
structure to prevent.
a) position error
b) instrument error
c) protection against ice formation
d) both a & c are correct**
12. The purpose of annealing is to:
a) soften the metal
b) releave internal stresses
c) both a & b are correct**
d) none of these
13. The given tool is used for:
a) counter sinking**
b) counter boring
c) drilling
d) any one of the above
14. Aviation ship is used for cutting:
a) heat treated Al-alloy & stainless steel**
b) Cu & its alloy
c) Any soft metal
d) All the above
a)
b)
c)
d)
porosity crack**
slashing
deforming of weld
none of these
22. A screw having no head flush with the structure can be turned by:
a) allean key**
b) screw extractor
c) simple screw driver
d) both (a) if have hex grove head and (b)
23. As per figure it is:
a) sector gear
b) as a & when used with external gear it gives the intermittent rotary motion
c) spur gear having few teeth broken
d) both a & b are correct**
24. In oxyacetylene welding to extinguish the flame it is good practice to:
a) first close oxygen and then acetylene regulator
b) first close acetylene and then oxygen regulator**
c) close oxygen and acetylene regulators at a time**
d) none of these
25. For welding cracks which type of joints should be preferred:
a) butt joining**
b) lap joining
c) edge joining
d) none of these
26. In brazing which type of flame is used:
a) carburizing
b) neutral**
c) oxidizing
d) any one can be used
27. The given tool is used for making spot facing to seal the washer, nut bolt head is:
a) counter sink
b) counter bore**
c) reamer
d) any one of them
28. The extended round portion which is indicated by letter A in the above figure is
known as:
a) pilot**
b) straightner
c) guide
d) all the above are wrong
29. For making neat and clean welding:
a) after welding remove the excess metal with file
b) the filler material should be properly filled and evenly spaced
c) fill the gap with Cu of brass
d) all are wrong**
ANSWERS:
1. A
2. A
3. C
4. A
5. A
6. A,B
7. A,C
8. A
9. B
10. C
11.D
12. C
13. A
14. A
15. A
16. B
17. C
18. D
19. A
20. B
21. A
22. A
23. D
24. B,C
25. A
26. B
27. B
28. A
29. D
30. D
31. D
32. C
33. A
34. B,C
35. A
36. A
37. D
38. C
39. A
40. D
41. C
42. B
9. Inductive reactance
a) directly proportional to the frequency of induction
10. The amount of electricity a capacitor can store is increased
a) decreasing the area of the plate
b) decreasing the distance between the plates
c) increasing the distance between the plates
d) selecting the low value of dielectric constant
11. The total current flow in the circuit is
a) 0.24
b) 0.44
c) 1.44
d) 0.84
12. The best matrix material of composite structure must possess low viscosity easier
curing methods and processing conditions. With good chemical thermal stability. On the
above accounts the best matrix is
a) polyester
b) epoxy
c) phenolic and polyamides
d) bismaleimide
13. Which one of the following types of epoxy resin is best for fire resistance
a) standard DGEBA resin
b) epoxy novolic and cyclo-aliphatic resin
c) halogen Ted epoxy
d) flexible epoxy resin
14. Composite structures are tested using conventional radiographic equipment, however
this method can detect defect of
a) large single void
b) porosity
c) cracks parallel to beam axis
d) cracks normal to beam axis
15. Mark the correct statement in respect to inspection methods used for composite
materials
a) the thickness of the laminate and depth of discontinuity does not pose any
problem in C scan method
b) the pulse feature of acoustic emission is analyzed to detect microscopic defect in
acoustic emission method
c) thermos copy is most difficult method since it require material with high thermal
conductivity
d) all the above are correct
16. The deflecting structures like wing should withstand large tensile and compressive
load for which most suitable composite structure is
a) nomad with fiber glass skin
b) sandwich of the fiber glass core and nomad skin
c) sandwich of fiber glass and graphite composite
d) any one of the above method used
(COMPUTER)
17. Main memory unit of computer
a) stores bulk of data and instructions
b) stores small amount of data and instructions
c) performs air thematic
d) supervise the working of all the units
18. The capability of the computer system to take logical decisions helps it in
a) making faster calculations
b) storing huge amount of data
c) decision making
d) none of these
19. The unit of computer performing calculations is
a) input unit
b) memory
c) output unit
d) A.L.U (Arithmetic Logic Unit)
20. The basic arithmetic operation performed by a computer is
a) addition
b) subtraction
c) multiplication
d) division
21. A finite sequence of steps needed to solve a problem is called
a) a process
b) a method of solution
c) an algorithm
d) a flowchart
22. In computing basic control structure always has
a) one entry and two exit points
b) two entry and one exit points
c) one entry and one exit points
d) any number of entry and exit points
d) 0.31255
44. Which treatment process of metal produces a hard and wear resistant surface area
with strong and tough in core
a) case hardening
b) tempering
c) annealing
d) normalizing
45. The diametrical pitch of a gear is
a) An imaginary circle passing through the points at which meshing of teeth takes
place
b) The diameter of the pitch circle
c) The number of teeth per inch of pitch diameter
d) None of the above is correct
46. In connection with square thread, mark the correct statement
a) the width and depth of the thread are equal to the space between threads
b) it is very strong
c) accurate machining of this thread is difficult
d) all of the above are correct
47. While drilling a hole, of the finished hole ahs a rough surface, the cause is
a) dull drill was used
b) the drill penetrated the work very slowly and become very hot while in operation
c) the drill hole was made very rapidly
d) both a & b are correct
SEPTEMBER
1. The most commonly used symbols for electromagnetic flow direction method is
a) UFD
b) MFD
c) PFD
d) EFD
2. In oxyacetelene welding it is better practice while shutting off the flame
a) Shut off oxygen first
b) Shut off acytelene first
c) Turn off the regulator
d) Turning off simultaneously
3. The silver soldeny metal melts at
a) 200-400 degree cent
b) 500-850 degree cent
c) 1000-1600 degree cent
4. The core of reinforced polymer thermoplastic is filled as
a) metal
b) fibre glass and plastic resin
c) carbon
d) all of the above
5. Synthetic thermoplastic
a) when heated becomes soft
b) when cooled becomes hard
c) when heated becomes hard
d) both a & c are correct
6. A crack may be repaired by
a) butt welding
b) spot welding
c) lap welding
d) edge welding
7. Annealing is the process
a) makes a metal soft
b) relives the internal strain
c) toughen the metal
d) both a & b are correct
8. T & W are the symbols utilized for heat treatment of Al-alloy sheet indicates
a) solution heat treated only
b) solution heat treated & quenched but not aged
c) precipitation heat treated
d) solution heat treated & artificially aged
25. In gear system, a driver and driven on the shaft to get the same direction of rotation
a) bevel gear is used
b) internal and external gear combination is used
c) as in (a) and no mechanical advantage is obtained
d) none
26. In regular interval, to calibrate a micrometer where you carried out
a) in normal environment and controlled temperature
b) in air conditioned room but does not proof
c) a room is calibrated upto 20-30 microns, but not air conditioned
d) a room is calibrated upto 100-150 microns, and also air conditioned
27. To bring the sheet together to get air tight joint, we use
a) draw set
b) cleco fastener
c) aligning camp
d) none
28. Choose correct statement
a) Philips screw-driver is blunt at end
b) Read and prince screw driver is blunt on end
c) Bot are interchangeable
d) All
29. To avoid vibrating stress in tube lines
a) no bend is done
b) two bend is done
c) atleast one bend is done
d) preferably no bend is done, and if bend is done, it will be less than 45
30. Dzus fastener consists of
a) stud, washer and receptacle
b) stud, gramate and receptacle
c) as in (b) and gromate is made of spring
d) none
31. Air drill in aviation industry is preferred to electric motors
a) no other equipment is required
b) it is available in various shape, sizes, running speed, drilling head angle
c) high initial cost and less maintenance
d) both a & b
32. Double flaring is
a) provide smooth and concentric surface
b) as in (a) and resistance to shearing effect of torque
c) as in (b) and generally used in a/c
d) as in and diameter of tube is reduced
26. In different countries, the same rate battery was charged which gets more charged
a) 80f, 1 hr
b) 80of , 1 hr
c) 60of, 30 min
d) 70of, 45 min
27. BA british unified bolts and screws can be recognized by
a) violet dye
b) UNF stamping on the bolt
c) Raised or recessed circles on the head
d) All of the above
28. In case of flouruscent die penetrant inspection, the developed used is
a) dry power
b) powder suspended in volatile liquid
c) powder suspended in water
d) all of the above
29. Round head rivet is
a) 430
b) 442
c) 462
d) 456
30. Fretting corrosion effect
a) thickness of the parts will be reduce
b) parts get brittleness
c) toughness increase
d) fatigue strength of parts decreases
31. When selecting a rivet for replacement of a solid rivet, we observe for
a) dissimilar actual corrosion
b) shape of head
c) length of rivet
d) none of the above
32. Fillet welding is
a) edges joined perpendicularly by
b) edges joined parallely by clambering
c) edges joined keeping the plates one over the other parallely, one being horizontal
d) clearance done at the edge of the gear teeth
33. American standard control cables are made of
a) Molybenium steel
b) Cast steel
c) Stainless steel
d) Brass
34. For most satisfactory plating on AGS and non steel materials
a) nickel plating
b) cadmium plating
c) zink plating
d) galvanizing
35. Though surface of castings and barrs etc removal, by an abrarive cutting tool is called
a) grinding
b) snagging
c) lapping
d) finishing
36. Replace a solid rivet with a hollow rivet we would check for
a) material and compression strength
b) material and shear strength
c) heat treatment
d) material and tensile strength
37. DTI indicator is
a) eccentricity of a small levels in rotating shafts
b) to measure the dimension
c) to check the depth of large parts
d) all of the above
38. In hot oil and chalk methods the following can not be detected
a) vertical cracks
b) horizontal cracks
c) wavy cracks
d) minute flows and tightly shut cracks
39. The following washers are not used on the part which is exposed to air flow
a) plain washer
b) special washer
c) lock washer
d) a & b
40. How many types of fits according to American standards
a) three
b) six
c) eight
d) four
41. Structural screw will have
a) same strength of the AN bolt
b) half of strength of the AN bolt
c) sometime less than half of strength of the AN bolt
d) both b & c are correct
105. Identify:
a) anchor, nut with double lug
b) anchor nut with single lug
c) anchor nut at corner lug
d) none of the above
106. Identify
a) cylinder
b) conical
c) rectangular
d) circular
107. Mark the correct statement:
a) diode is used as a rectifier
b) triode is sued as a rectifier
c) diode is used as a amplifier
d) all of the above
108. Identify
a) circular shaft
b) splinged shaft
c) gear & pinion
d) bearing
109. Identify:
a) gear & pinion
b) buck & gear
c) worm & worm gear
d) none of the above
110. Identical insulated wire coils are hung from air so that they are racing each other and
supplied with same direction A.C.,
a) anti clockwise rotation
b) both are repelled
c) both are attracted to each other
d) clockwise rotation
111. Identify:
a) improper upsetting
b) bucking bar not in place
c) rivet driven too much
d) over sized rivet
112. Which of the following has negative co-efficient of resistance
a) thermistor
b) transistor
c) semiconductor
d) resistor
121. Identify:
a) adjustable tap wrench
b) a) T handle tap wrench
c) T socket wrench
d) Allen wrench
122. Identify:
a) combination wrench
b) box wrench
c) close end wrench
d) crescent wrench
123. The size range of an allen wrench is
a) 3/64 to
b) 1/64 to
c) 3/64 to 1/8
d) 1/64 to 1/8
124. identify
a) collet
b) ring gage
c) check gage
d) none
125. The function nut on an a/c landing gear requires a torque of 100 inch pounds. To
reach the nut, a 3 straight adapter must be used on an 15 torque wrench. How many
inch pound will be indicated on the torque wrench when the required torque of the nut is
reached?
a) 100
b) 83.3
c) .80
d) 115.6
126. Carbon steel is:
a) strongly magnetic and shows slow chemical reaction with nitric acid test
b) non magnetic and non action with HN
c) strongly magnetic and rapid action with HNO3 test
d) slightly magnetic & slow chemical reaction with HNO3 test
127. In a vernier micrometer, 9 part of main scale is divided into 10 parts of vernier scale,
the main scale has graduation of 1mm. Find the least count
a) 0.01 cm
b) 0.001 cm
c) 0.001 mm
d) 0.009mm
128. In a given figure, what may be the cause of fault for the installation of rivet?
a) greater allowance on the formal head
b) snap not regular to the head
c) bueking bar not in position
d) none
129. The type of corrosion which occurs when two making surfaces, normally at rest with
respect to one another, are subject t slight relative motion is know as?
a) stress corrosion
b) fretting corrosion
c) crevice corrosion
d) inter granular corrosion
130. The letter: 0 in heat treatment process represents the following condition
a) strain hardened
b) annealed
c) solution heat treated
d) none
131. When an aircraft catches fire, (made of aluminium) conductivity & resistivity of
aluminium respectively
a) increases decreases
b) decreases increases
c) both will increases
d) both will decreases
132. The rivet head indicates the material
a) 2024
b) 21171
c) monel (nickel copper alloy)
d) none
133. The abbreviation Unix used in computer indicates:
a) a new operating system
b) operating system other than MS-DOS (Microsoft disk operating system)
c) PC-AT computer may have Unix operating system in addition of MS-DOS
d) None of the above
134. The most sophisticated computer is
a) micro computer
b) first generation computer
c) super computer
d) none
135. Which is principal load carrying member in composite materials
a) fabric
b) matrix
c) resin
d) none of the above
136. Two wires each one meter long are kept at a distance of 0.02 mt apart if 1 amp
current is flowing through each wire, then force acting on the wire will be
a) attractive if the direction of the current flowing through wires is same
b) attractive if the direction of current will opposite
c) repulsive if direction of current will be reverse
d) both b and c are correct
137. The symbol represents
a) SCR, rehostat respectively
b) Rehostat, thyristor respectively
c) Resistor, FET (field effect transistor) respectively
d) None of the above
138. In which condition the bridge is said to be balanced
a) R1 is increased, R2 is decreased
b) R3 is increased, R4 is decreased
c) R2 is increased, R3 is decreased
139. Which one of the following statement is true?
a) In Ni-cd battery, charging and discharging can be done rapidly due to low internal
resistance
140. In case of a battery, which of the following quantity can be stored?
a) energy
b) charge
c) current
d) none of the above
141. In a dry cell battery
a) carbon electrode is placed centrally surrounded by aluminium chloride electrolyte
b) zinc chloride is placed centrally surrounded by aluminium chloride electrolyte
c) carbon electrode is placed centrally surrounded by zinc chloride electrolyte
d) both a & c are correct
142. The identical insulated wire coils are hung from air so that they are facing each other
and supplied with same direction
a) both are attracted to each other
b) both are repelled
c) clockwise rotation
d) anti clockwise rotation
143. Hot water quenching
a) minimizes distortion and alleviates cracking
b) ensures maximum resistance to corrosion
c) minimizes distortion but results in cracking
d) a & b are correct
or A indicates
anhealed recrystallized
quenched
forged
both a & b
10. As the presence of figure and find the amount of torque applied to a fastener by the
torque wrench
a) 120
b) 150
11. The tool shown in figure is
a) single bewel cape chisel
b) double bewel cape chisel
c) diamond point, chisel
d) none
12. Mark the correct name of the figure
a) turn buckle barrel
b) turn buckle fork
c) turn buckle pin eye
d) both b and c
13. Mark the correct figure
a) a & c
b) b & c
c) a & d
d) b & d
14. With increase in temperature, resistance of cu
a) increase
b) decrease
c) infinite
d) same
15. If the plate is more +ve w.r.t cathode, the electrons
a) will start to flow toward plate
b) will not start to flow toward plate
c) will start to flow toward plate but will damage diode none
d) none
6. Which of the NDT testing method is suitable for the inspection of most metal, plastic
and ceramic surface defects
a) eddy current
b) magnetic particle inspection
c) ultrasonic test
d) dye penetrant method
7. How many of these factors are considered essential of knowledge for x-ray exposure
i) processing of film
ii) material thickness and density
iii) exposure distance
iv) film characteristics
a) 1
b) 2
c) 3
4) 4
8. Which type of crack can be detected by magnetic particle inspection using either
circular or longitudinal magnetization
a) 45
b) longitudinal
c) transverse
d) sub-surface
9. Alclad is metal consists of
a) Al-alloy surface and pure Al-core
b) Pure Al-surface and Al-alloy core
c) A homogenous mixture of pure N and N-alloy
d) All are correct (multiple layer of Al-alloy and pure N)
10. A fibre type self locking nut must not be used on a/c if bolt is
a) under shear load
b) under tensile load
c) subjected to rotation
d) subjected to vibration
11. A triode consists of
a) plate, grid and a heater
b) plate, cathode and heater
c) cathode and a plate
d) plate, cathode, heater and a screen between the plate and cathode
12. Diode, triode and transistors
a) obeys ohms law
b) does not obey ohms law
c) not a linear resistance
d) both b & c are correct
13. Considering all factors the most commonly used metal as electrical conductor in a/c is
a) aluminium
b) copper
c) silver
d) tongesten
14. A galvanometer may be converted to a voltmeter by connecting
a) low resistance coil in parallel with meter
b) high resistance in parallel to meter
c) low resistance in series with meter
d) high resistance in series with meter to increase range
15. The figure indicates
a) three phase delta alternator connection
b) three phase Y connection for alternator
c) three phase delta to Y transformer connection
16. As per ATA 100 code the size & type of electrical wire in aircraft are given
a) by prefix and suffixes
b) side by side
c) at the beginning and at the end
d) by letters and numbers
17. Transformer is a device
a) used in transistors set
b) transfer electrical energy from one circuit to another by changing frequency
c) both a & b
18. Hydrogen evolves
a) towards the end of the charging cycle of Ni-cd battery
b) throughout the servicing of lead acid battery
c) when the battery is over charged
d) all of the above
19. The strength of an electromagnet depends on
a) No. of the turns of the coil
b) Strength of rotation of the magnet
c) Speed of rotation of the magnet
d) All
20. The setting in vernier caliper indicates
a) positive error
b) negative error
c) no error
d) all are false
7. 7075 0 indicates
a) full annealed condition
8. Which of the following revet does not required heat treatment
a) 2017
b) 2117
c) 2024
9. In oxyacetelene welding equipment oxygen and acetylene are identified by
a) left and right hand thread
b) color and length of cylinder
c) diameter of the hose
d) both a & b are correct
10. Cleaning of acrylic and rubber is done by
a) MEK
b) Aliphatic naptha
c) Aromatic naptha
d) Acetone
11. Elastometer rubber is
a) rubber impregnated in metal
b) shock absorber
12. NDT of aluminium alloy is done by
a) penetrant method
b) zyglo method
c) X-ray method
d) Ultrasonic method
13. Heat treatment aluminium alloy is done by
a) heating in KOH and NAOH
b) heating above critical point and cool in air
14. UFD indicates
a) ultrasonic flow detection
b) radiography
c) dye penetrant flow detection
15. Welding for stainless steel the flame used
a) carbursing
b) neutralizing
c) caldizing
16. Carbon in iron at normal temperature remains as
a) ferrite
b) dissolved iron matrix
c) austenite
d) special iron matrix
45. Gyroscope the phenomenon which causes continious spin of outer ring due to
coincidence of rotor ring with cuter gimble ring axis is called
a) gyro wander
b) gyro tambling
c) apparent precession
d) gimble lock
46. Rate of turn indicator
a) rate gyro
b) tied gyro
c) earth gyro
d) free gyro
47. Difference of pilot and static pressure is measured by
a) ASI
b) Altimeter
c) VSI
48. True airspeed of aircraft is maximum
49. Altimeter operation mechanism consists of a
a) two aneroid capsule
b) three aneroid capsule
c) adjustment for barometric pressure provided
d) all
50. Free gyro has
a) the plane of freedom
b) the planes are right angle to each other and three plane
51. Turn and slip indication operates respective by
a) gyro only
b) external force and gravity
c) gyro and gravity
52. Acceptable deviation in compass from the equipment
a) 1 degree from the needle to the compass
b) 2 degree from the needle to the compass
c) 3 degree from the needle to the compass
53. Spherical roller bearing will take
a) radial load heavy
b) axial load slightly
c) both
54. Micron is
a) millionth of meter
b) thousandth of meter
55. A hole to be reamed should be drilled to under
a) 0.001 0.002
b) 0.003 0.007
c) same size
56. Every third tooth of the hackshaw is made straight
a) to give clearence for the cutting
b) repsaw tooth is provided
57. The vernier scale has
a) +ve error
b) ve error
58. Least count is defined as
a) one main scale division is divided into the total division of the vernier / thimble
scale
b) 1 MSD 1 TSD
59. Least count of 50 divisions on the circle of micrometer whose pitch is 1mm
a) 0.01 mm
b) 0.02 mm
c) 0.5mm
d) 0.002 mm
60. Backslash of a micrometer is caused due to
a) manufacturing defect
b) wear and tear
c) wear on the nut
d) all
61. Snap gauge is a
a) go & no. go guage
b) it will snap at preset torque load
c) guage which measure TPI
d) guage which measures outside diameter
62. Aviation snip used for cutting
a) stainless steel and aluminium alloy heat treated sheet
b) chromium sheet
c) heavy sheet metal
d) any sheet metal
PAPER II (JUNE
1. The main memory of a computor is
a) RAM
b) ROM
c) Hard disc
d) Micro processor chips
2. The binary 110 equivalent of 55 is
a) 100011
b) 110001
c) 100001
d) 110011
3. T6 designation of Al-alloy indicates
a) solution heat treated and then artificially aged
b) solution heat treated and then stabilized
c) artificially aged only
d) solution heat treated and then cold worked
4. 0.10 mmis equivalent to
a) 0.039
b) 0.041
c) 0.035
d) 0.045
5. The major alloying element in 7075 Al-alloy is
a) magnesium
b) silicon
c) Mg and Si
d) Zinc
6. The purpose of turnbuckle is to
a) make minor adjustment in cable length
b) adjust cable tension
c) both a & b
d) none
7. A 7x19 cable is made up of
a) 7 strands of 19 wire each
b) 19 strands of 7 wire each
c) both
d) none
24. Through which material will magnetic lines of force pass the most
a) copper
b) iron
c) aluminium
d) all are correct
25. Which symbol represent a variable resistor
a) 2
b) 3
c) 1
d) all
26. With an ohmmeter connected into the circuit as shown, what will ohmmeter read
a) 20
b) infinite
c) 10
d) none
27. How can the state of charge of a Ni-cd battery be determined
a) by measuring the specific gravity of the electrolyte
b) by measuring charge
c) by the level of electrolyte
d) all
28. Which statement concerning the depicted logic gate is true
a) any input being 1 will produce 0 output
b) any input being 1 will produce 1 output
c) all input must be 1 to produce a 1 output
d) none
29. Zero fuel weight is the
a) dry weight plus the weight of full crew, pax and cargo
b) basic operating weight without fuel
c) maximum permissible weight of a loaded a/c including pax, crew, cargo without
fuel
d) maximum weight of the a/c with crew, oil, pax, less fuel in wing tank
30. The empty weight of an aircraft is determined by
a) adding the net weight of each weighing point and multiplying the measured
distance to the datum
b) subtracting the tare weight from the scale reading and adding the weight of each
weighing point
c) multiplying the measured distance from each weighing point to the datum times
the sum of scale reading less the tore weight
31. Unless otherwise specified, torque value for tightening a/c nuts and bolts relate to
a) clean dry thread
b) clean. Lightly oiled thread
c) either a or b
d) none
32. A fibre type, self locking nut must never be used on an a/c if the bolt is
a) under shear loading
b) under tension loading
c) both tension and shear loading
d) subjected to rotation
33. Aircraft bolts are usually manufactured with a
a) class 1 fit for the threads
b) class 2 fit for the threads
c) class 3 fit for the threads
d) class 4 fit, for the threads
34. Generally speaking, bolt grip length should be
a) one and one half times the thickness of the material through which the extend
b) equal to the thickness of the material through which they extend plus
approximately one diameter
c) equal to the thickness of the material through which they extend
d) 2 times the diameter
35. A particular component is attached to the a/c structure by the use of an a/c bolt and a
castleted tension nut combination, if the cotter pin hole does not align with the
recommended torque range, a acceptable practice is
a) exceed the torque range
b) lubricate the threaded section of the nut, bolt and torque
c) change washers and try again
d) change the nut
36. How is a clevis bolt used with a jork-end cable terminal secured
a) with a shear nut lightened to a snug fit, but with no strain imposed on the fork and
satefied with a cotter pin
b) with a castle nut tightened until slight binding occure between the fork and the
fitting to which it is being attached
c) with a shear nut and cotter pin or a thin self locking nut tightened enough to
prevent rotation of the bolt in the fork
d) all are correct
37. A bolt with an X (cross) inside a triangle on the head is classified as a
a) standard a/c bolt
b) close tolerance bolt NAS
c) CRS bolt
d) Special bolt
8. N.W.V
a) strength of the compositor material
b) strength of the material and composing with charge
c) strength of reinforcing fibre
d) none
9. AN flared tube fitting is made of
a) Al
b) Cu base alloy
c) Steel
d) All
10. Correct statement regarding refueling is
a) earthing is not required
b) disconnect the earthing line first before disconnecting the fuelling nozzle
c) if a/c is earthed, fuelling vehicle, doesnt require earthing
d) none
11. Scales are removed from lightly stressed steel parts by
a) hard abrasive paper
b) buffing wheel
c) wire brush
d) none
12. If you have some 178 rivet, above 3/16 in dia, that had been aged for the hours after
quenching
a) you could use them frouding they have not exceeded 5 hours of ageing
b) you could not use them because 178 rivets should be used within 10 minutes after
quenching
c) you could use them provided they had not exceeds 3 hours of ageing
13. Flux from ferrous metals can be removed by using
a) 25% sol of silver nitrate
b) no need of flux by welding ferrous metals
c) you have to remove flux from ferrous metals
d) a wire brush
14. A flux for silver soldering is obtained by using
a)
Zn Cl2
b)
Nitric acid
c)
Muriatic acid
d)
None
15. Welding of AC from welding of steel differs in that
a) it is considered harder to weld because of high temp
b) steel does not have a color change that is apparent in Al
c) M.P. of Al is much lower than steel and the expansion is nearly three times as
great
d) It is much easier to weld because a flux is used
16. What procedure is used to distinguish heat treatable alloys from non heat treatable
alloys
a) 10% solution of caustic soda
b) 5% sol of muriatic acid
c) Rockwell test
d) 10% solof H2Sc
17. When welding various metals you may reduce the chances of during by
a) preheating
b) anodizing
c) heat treating
d) clamping
18. Which of the follow of a/c parts or units should not be welded
a) items which are not responsive to heat treatment
b) plain carbon, Ni-steel of SAE 2300 series
c) turn buckle barrel ends
d) steel tubular members of basic structure
19. When welding a high carbon steel use a
a) low carbon rod
b) high carbon rod
c) rod of either low or high carbon content
d) rod of intermediate carbon content
20. High carbon steel can be readily welded by
a) are welding procedure
b) oxidizing flame and high carbon rod
c) neutral flame and high carbon rod
d) carbonising flame and low carbon rod
HARNESS TESTER
spark
idler
Rockwell
ball
1. Knurling is the
a) rolling depression on the soft material
b) rolling depression on any kind of material
c) as in (b) and is used to provide proper grip
d) none above correct
2. To make stretch in the direction of its width
a) use straight peen hammer
b) use cross peen hammer
c) any kind of hammer can be used
d) use ball peen hammer & apply blow with an angle
3. Protective jaw caps are used with vice
a) to protect the vice jaw
b) to protect the parts from becoming damage
c) to apply constant and even pressure on the parts
d) all above correct
4. To make a V-shaped groove the chisel commonly used is
a) round nose chisel
b) flat chisel
c) cap chisel
d) diamond point chisel
5. To locate the center on a round block use
a) surface gauge
b) center square head
c) hermophrodite caliper
d) all
6. Which cutting fluid is used on load steal
a) mineral land oil
b) soluble oil & (a ) is correct
c) sulfurized oil
d) all above correct
7. Mark the correct statement
a) linear sidewise motion is known as backlash
b) reaming should be down after drilling
c) as diametral pith increases, braze of tooth decreases, no. of teeth increases
d) all above correct
a)
b)
c)
d)
Rubber
cast iron
steel
brass
15. Conductor having length of 2 ft and resistance 2 ohms, now if we reduce its length
just half of original, then resistance will be
a)
b)
c)
d)
just double
just half
just equal
none above correct
16. Which instrument is utilizing both dynamic and static air for its operation
a) Altometer
b) VSI
c) ASI
d) Both a & c are wrong
17. The sensitively of altimeter is increased by increasing
a) No. of gears and sectors
b) No. of gears and pinion
c) No. of capsules
d) Both a & c are correct
18. Mark the correct statement
a) a suspended magnet always assume a north and south position
b) inductors when connected in parallel the total inductance is the south their values
c) inductive reactance is inversely proportional to inductance & frequency
d) all above correct
19. Which instrument is used for checking the insulation resistance
a) ohm meter
b) megger
c) as in (a) and maghometer
d) all above correct
20. D Arsonavel ammeter is used
a) for measuring ammeter A.C. current
b) for measuring D.C. current
c) for measuring A.C. voltage
d) for measuring D.C. voltage
21. Mark the correct statement
a) specific gravity reading between 1.300 to 1.275 indicates a high of charge
b) specific gravity reading between 1.275 to 1.240 indicates a high of charge
c) specific gravity reading between 1.240 to 1.225 indicates a medium charge
d) both a & c are correct
22. In triode tube
a) crid is placed between place & cathode
b) plate is placed between grid & cathode
c) cathode is placed between grid & plate
d) none above correct
23. The given figure indicates
a) NPN transistor
b) PNP transistor
c) As in (a) and arrow indicating emitter
d) As in (b) and arrow indicating emitter
24. In heat treatment of material T8 indicating
a) solution heat treatment and then stabilized
b) solution heat treated and artificially edged and then cold worked
c) solution heat treated and cold worked & then artificially edged
d) solution heat treated, and then artificially edged
25. In Rockwell hardness tester there is two weight except weight pan of machine, one is
red and other is black. Now choose correct answer
a) when there is no load machine applied a load of 60 kg
b) where black wt. Is on the pan, machine applies a load of 150 kg
c) as a & b and when red wt. Is on the pan machine applies a load of 100 kg
d) as a,b, & c and black wt. Is always used with red wt.
26. Titanium is heat treated for the purpose of
a) thermal hardening to improve strength
b) annealing after hot working or cold working
c) relief of stresses setup during cold working
d) all above correct
27. Filler are added in resin to
a) increase strength
b) as in a & b, also control viscosity & wt
c) increase pot, life
d) as in (b) also control viscosity and wt
28. Mark the correct statement regarding composite material
a) carbon/graphite is stronger in compressive strength
b) color of kevler is brown
c) S-glass is borosilicate glass
d) All above correct
29. Mark the wrong statement
a) nomex is the widely used core material
b) urothane can not be cut by hot wire cutter
c) carbon is identified by its black color
d) ciramic fibre are in not used with metal matrix
30. Stress corrosion occurs as a result of
a) combined effect of tensile stress & lack of uniformity in alloy structure
b) relative motion between two parts
c) combined affect of tensile strength and corrosive environment
d) combined effect of compressive stress and corrosive environment
31. Which is the correct statement
a) gasket are always used with backup ring
8. The given figure indicating fault which occur during the bending of tubing which is
correct statement
a)
b)
c)
d)
kinked bend
wrinkled bend
corrugated bend
flattened bend
b) shell reamer
c) jobbers reamer
d) none above correct
25. Which statement is correct
a) single thread lead equal to the pitch
b) in double thread, pitch is double of the lead
c) in triple thread, pitch is triple of the lead
d) both b & c are correct
26. During spark test of nickel, which color of spark will produce
a) orange
b) white
c) red
d) straw yellow
27. function of disintegrator is to
a) make hole without producing chips
b) make hole of any shape
c) as in a & b and also make hole in any kind of material
d) check the accuracy of surface plate
28. Mark the wrong statement
a) for insite check, the penetrate dye process is useful
b) crack is indicated by a red stain termed by the dye in case penetrate dye process
c) radiographic inspection is not suitable for surface crack
d) the eddy current inspection offers improved sensitivity as compared other NOT
best
29. The function of torch tip is to control the
a) amount of heat
b) flow of gases
c) both a & b are correct
d) all above wrong
30. Galvanizing is the process of coating zinc is normally carried out on
a) Al-alloy
b) Iron and steel
c) Steel parts
d) Mag-alloy
9. In pentude
a) Screen grid is placed between suppressor grid and control grid
b) Control grid is placed between suppressor grid and screen grid
c) Suppressor grid is placed in between control grid and screen grid
d) There is no suppressor grid
10. Zener diode are used for
a) voltage regulation
b) some times called break down diode
c) both a & b are correct
d) converting ac into dc with mechanical aid
11. As per given fig.
a) arrow is indicating direction of conventional current flow
b) A-N type, B-P type
c) Both a & b are correct
d) As in A and A-P type, B-N type
12. Voltage induced by generator is maximum when loop is
a) perpendicular to the lines of force
b) parallel to the lines of force
c) coming away from lines of force
d) going towards the line of force
13. As fig. Is indicating
a) delta connecting inverter
b) wye connecting inverter
c) delta connecting alternator
d) wye connected alternator
14. A two pole alternation having 1800 rpm has freq. Of
a) 60 cps
b) 120 cps
c) 30 cps
d) 90 cps
15. Inverter are producing current at frequency of
a) 300 cps
b) 400 cps
c) 200 cps
d) 450 cps
16. Ball bearing can take
a) radial load only
b) axial load only
c) both radial and axial load
d) it takes thrust only load
24. Fuses are normally made up of metal having low melting point statement is true
a) low melting point material is alloy of tin and bismuth
b) if fuses made of copper than it is called current limiter
c) as a & b and fuses are installed in the circuit so that all the current must pass
through it
d) only (a) is correct
25. Micro switches are mostly used in a/c, making contact open or close movement is
about
a) 1/8 inch or less
b) 1/6 inch or less
c) 1/16 inch or less
d) inch or less
26. Which equation is used to find out capacitive reactance
a) Xc=2fc
b) Xc=1/2fc
c) Xc=2/fc
d) Xc=1/4fc
TITANIUM
a) Ni-Cr steel
b) Teeth
c) Non-magnetic
d) Teeth
BEARING
Non-magnetic
Ni-Cr
Ni-Cr
Ni-Cr
GEAR
Teeth
Non-magnetic
Teeth
Non-magnetic
a)
b)
c)
d)
a)
b)
c)
d)
a. Electron
b. Alduminium
c. Duralumin
d. Al clad
a-A, b-D, c-C, d-B
a-B, b-D, c-C, d-A
a-C, b-D, c-A, d-B
a-D, b-C, c-A, d-B
A Al
B Mg
C Al
D Al
A 2024
B corrosion resistant steel
C colored lacque
D Al alloy
a)
b)
c)
d)
black color
yellow color
white glaming color
brown color
38. Which formula is used for calculating the inside dia. Of an internal gear
a)
b)
c)
d)
e)
Ng Np/2c
N 2/DA
PD 2/DP
Ng Np/2P
Ng Np/DP
a)
b)
c)
d)
internal thread
external thread
tap bold
none of the above
a)
b)
c)
d)
a)
b)
c)
d)
lap joint
butt joint
single rivets butt joint
corner joint
a)
b)
c)
d)
a)
b)
c)
d)
a)
b)
c)
d)
a)
b)
c)
d)
56. The identical insulated wire coils are hung from air to that the facing each other and
supplied with same directing A.C
a) both are attracted to each other
b) both are repelled
c) clockwise rotation
d) anticlockwise rotation
57. Identify the fig.
a) improper upsetting
b) buckling bar not in place
c) rivet driven too much
d) over sized rivet
58. Which of the following has negative coefficient of resistance
a) thermistor
b) transistor
c) semi conductor
d) resistor
59. In a 4 stroke cycle the spark plug fires for every
a) 4 revolution of crank shaft
b) 2 revolution of crank shaft
c) 1 revolution of crank shaft
d) 360 degree revolution of crank shaft
60. If a wire having a resistance of 9 ohm is increase its length twice, then new resistance
is
a) 1 ohm
b) 8 ohm
c) 6 ohm
d) 4 ohm
61. If resistor of 30 ohm are connect and battery voltage is 2v then a meter reads
a) 1/10 A
b) 3/10 A
c) 7/10 A
62. Identification of titanium
a) spark
b) not standing and making in glass
c) acid best
d) both a & b are correct
63. Annealed metal is
a)
b)
c)
d)
to soft
low strength
relieved internal stresses
all above are correct
a)
b)
c)
d)
iron scrappers
steel
mild aspiration or hand plashed with aluminum
all of the above
b) the distance from the center of our teeth to another teeth measure pitch circle
c) the distance from the centre one teeth to center of next teeth
d) none of the above
88. The binary expression for 296 is
a) 101011101
b) 100101000
c) 111001100
d) 110010111
89. The nd. of T.P.I. are measured by
a) screw pitch guage
b) SWG (standard wire gage)
c) Thickness guage
d) None of the above
90. The output of an OR gate will be given
a) when all the input are energized
b) when all the inputs are zero
c) anyone of the input is energized
91. Computer consist of
a) printer, decode, memory
b) input, output, C.P.U
c) input, output, printer
d) none of the above
92. The decimal no. for 10111011101 is
a) 1502
b) 1500
c) 1501
d) 1600
93. The drawing symbol shown in fig
a) fixed capaciter
b) variable capaciter
c) variable resister
d) fixed resistor
94. O-rings are checked for internal cracks by
a) 4 power magnifying glass
b) by rolling on inspection cone
c) by rolling on inspection dowel
d) all of the above are correct
95. Memory of computer are
a) Rom, C.P.U. ALU
b) 0.250 inch
c) 0.257 inch
d) 0.200 inch
104. In a fig.50 the logic symbol indicates
a) AND gate
b) NAND gate
c) XOR gate
d) None of the above
105. In a fig. 51 the logic symbol indicates
a) NAND gate
b) OR gate
c) NOT gate
d) XOR gate
106. In the case of circuits ohms law hold for
a) peak values of voltage and current
b) effective value of voltage and current
c) instentenneous value of voltage and current
d) all of the above are correct
107. In a purely inductive circuit the current
a) lags behind the voltage by / 2
b) loads the voltage by II/? Capacitive circuits
c) is in phase with the voltage
d) legs behind the voltage by II/2 at high frequency
108. The magnetude of the induced emf produced in all coil when a magnet is inserted in
to it does not depend upon the
a) no of turn in the coil
b) reactance of the coil
c) magnetic moment of the magnet
d) speed of the rotation of magnet
109. Chocks is used as resistance in practical inductive reactance in choke and
transformer
a) D.C circuit
b) A.C circuit
c) A & b are correct
d) Full wave rectifier
110. An A.C series circuit contains 4 ohms resistance and 3 ohm inductive reactance what
is the impedance of the circuit
a)
b)
c)
d)
1 ohm
5 ohm
7 ohm
7/R ohm
b) CPU
c) Keyboard
d) Hard disk
127. Identify:
a) threaded shank, body, pilot
b) mandrel, cutter, locater
c) tap, Cutter, Pilot
d) none of the above
128. While treating for magnetic testing it was found non magnetic, in nitric acid it was
found rapid action, greenish blue
a) nickel steel
b) 18-8 steel
c) monel
d) CRS
129. Analog computer is
a) more correct than digital computer
b) less accurate than digital computer
c) both a & b are correct
d) none of the above
130. In computer machine language is
a) high level language
b) low level language
c) very high level language
d) none of the above
131. Decimal equivalent to binary number 110 is
a) 2
b) 3
c) 6
d) 9
132. Aluminium alloy can be heat treated
a) solution heat treatment
b) precipetation heat treatment
c) both
d) artificial aging
133. In NDT inspection, performance of magnetic particle inspection can not effected by
a) cadmium
b) copper
c) tin & zinc
d) all of the above
134. The transferring metal from one object to another by chemical or electrical wings is
done to protect the base metal
a)
b)
c)
d)
against corrosion
increase strength to protect the base metal against chemical reaction
wear
all the above are correct
135. To improve tensile strength, ductility and shock resistance, magnesium casting are
normally
a) case hardened
b) solution heat treatment
c) precipetation heat treatment
d) none of the above
136. Hydrogen is given off:
a) in electrolyte
b) lead acid battery
c) in over heated condition
d) after fully charged condition in Ni-cd battery
137. As per ATA 100, identification of a/c electrical cables, letter and size are marked
a) in the middle
b) side by side
c) prefix & suffix
d) none of the above
138. In fig. 56 indicates
a) OR gate
b) AND gate
c) NOT gate
d) None
139. In modern a/c most popular heat treated aluminum alloy used in structural appliation
a) alloy 2024
b) alloy 5054
c) alloy 5003
d) alloy 7075
140. A coil is helped with a plain horizontal to certain surface and a bar magnet is
dropped vertically downward
a) the magnet will fall with constant acceleration equal to G
b) constant accelaration greater than G
c) constant accelaration less than G
d) non uniform accelaration less than G
b) power
c) both a & b
d) none of the above
142. The thickness of conducting and non conducting is done by
a) micrometer
b) eddy current
c) ultrasound
d) caliper
143. Evidence of corrosion on copper is indicated by
a) red spot on the surface steel
b) green spot in the surface
c) grey spot on the surface
d) none of the above
144. Evidence of corrosion on Al, alloy is indicated by
a) more shining portion near the surface area
b) grey spot
c) pitting on surface
d) power form
e) all
145. For high Al alloy the more suitable welding is
a) seam welding
b) spot welding or butt welding
c) electric resistance welding
d) all of the above
146. To measure skin thickness of hollow tubular member is normally done by
a) by distructing the tube
b) by micrometer tube
c) eddy current
147. The NDT radiography method the density means
a) degree of blackness
148. The computer mark the storage device
a) VDU
b) Printer
c) Mouse
d) Floppy disk
149. Expand the term Ram while loss the term Ram means
a) random access memory
150. Which language is the oriented language
a) pascal
b) basic
c) fortran
d) cobol
151. The third generation computer
a) intergretted circuit are used
b) microprocessor are used
c) semitransistor
d) all of the above
152. The unit of the memory is
a) bute
b) bits
c) nibhles
d) all
153. Expand the ??? basic
a) beginners all purpose symbol instruction code
154. The principle had carrying member in a composit structure is
a) fibres
b) matrix
c) adhesive
d) rasin
155. Intraply hybrid composites means
a) inforcing material of same fibre in different layers
b) reinforcing material woven from two more fibre types
c) reinforcing material different indifferent layer
d) none of the above
156. Metal matrix composite is a recent composite material where in
a) resin in reinforced with metal
b) resin and fibre and reinforced with metal
c) fibre are reinforced with metal during melton stage
d) all of the above are correct
157. Replacement of honey comb core segment to the existing honey done with help of
a) film form adhesive
b) freeing adhesive
c) epoxy resin with fibre
d) all of the above are correct
158. Two wires each other meter long are kept at a distance of 0.02 & 16.2 ampire current
is flowing through each wire, then force the wire will be
a) attractive if the direction of the current flowing through
b) repulsive if direction of current will be same
c) repulsive if direction of current will be reverse
d) both a & c are correct
b) to control the electron flow between the cathode, and the anode
c) none of the above
d) a & b are correct
175. The semi conducter having high negative co-efficient is
a) thermister
176. D.P indicates in a gear for
a) distance between two teeth
b) height of the teeth
c) pitch circle
d) all of the above
177. Diode triode or transistor works on
a) ohms law
b) donot obey ohms law
178. Change 1010101 in decimal
a) .85
b) .65
c) .111
d) none of the above
179. PN junction is knows as
a) forward bios
b) reverse bios
180. In a figure 59
a) completely dimensional part
b) perpendicularly
c) symmetry
d) parallelision
181. Counter sunk rivet:
a) when riveting different layers of sheets
182. In a step down transformer the input voltage is 220v and current 5A and the output
voltage is 11v and the current is 90A, the calculate the efficiency of the transformer
a) 30%
b) 90%
c) 60%
d) 70%
183. When 2 conductor of 1 mt in length carrying a current at 2 amp are .025 meter a part
from each other:
a)
b)
c)
d)
b) 1.0
c) .6 A
d) 1.2A
200. EDP stands for in computer:
a) electrical data processing
b) electronic data processing
c) entry data processing
d) electronic discrete program
201. Electronic digital computer performs :
a) mathematical calculation
b) data processing
c) strees data in given instruction
d) all of the above are correct
202. (010100)2 convert into octal:
a) (24)8
b) (15)8
c) (26)8
d) (50)8
203. This bolt in fig. 64
a) internal wrenching bolt
b) clevis bolt
c) Al alloy close tolerance bolt used with grease
d) As in and cadmium plated
204. Fillers is:
a) epoxy
b) cellulose
c) polyester
d) boron
205. Arrange the following:
a) Reduz
i. Cellulose
b) Struz
ii. Filler
c) epoxy
iii. Thermoplating
d) polister
iv. Thermocoating
206. Which statement is true for leveling:
a) leveling of large a/c is critical than lighter a/c
b) leveling is done normally on longitudinal axis
c) leveling is done more accurate on lighteral axis
d) none of the above
207. For jacking the a/c:
a) normally the jack points are given in all a/c
b) three points on a/c for jacking is provided to stabilize the a/c about three points
c) jacking points are located in relation to C.G. position
d) all the above are correct
208. Fuel lines are identified by:
a) color code and geometrical sign
b) color code
c) color code and name
d) all the above are correct
209. In ATA specification the electrical cable no is instructed as
a) extent ion tab
a. prefix suffix
b) pound split die
b. in middle
c) bottom tap
c. side & side
d) a & b are correct
d. all of the above
210. Thread in deep holes are cut by:
a) extension tap
b) round split die
c) bottoming tap
d) a & c are correct
211. Tool shown in fig. 65:
a) allen wrench
b) offset screw driver
c) Philips screw driver
d) Common screw driver
212. Punch shown in fig. 66
a) pin punch
b) aligning punch
c) starting punch
d) prick punch
213. Tool shown in fig. 66
a) combination wrench
b) box and wrench
c) open end and box wrench
d) double ended wrench
214. Size of flat cold chisel is identified by:
a) length of cutting edge
b) width of cutting edge
c) weight of the chisel
d) all of the above are correct
215. File shown in fig. 67
a) square file, taper
b) knife file
c) pillar file
d) none of the above
216. If twist drill is not printed clearly, it can be checked by
a) drill size guage no. system on left and fraction system on right
b) drill size guage with no. system on right fraction on left
c) SWG
d) By micrometer
217. Micrometer reading in fig. 68
a) 0.588
b) 0.578
c) 0.568
d) 0.563
218. Mark correct statement
a) A transistor connected in common-base configuration has a low input registance
and high output resistance
b) At transmeter connected in common omitter configuration a medium input
resistance and a output resistance
c) The input and output signals of a common omitter are out of phase
d) All the above are correct
219. The arrow head on the transistor symble always pointing the direction of
a) hole flow
b) electron flow
c) electrons are the majority carrier
d) holes are the majority carrier
220. The energy loss in a transformer is due to:
a) heating the coils
b) eddy current in the core
c) low permeability of ferro magnetic substance
d) both a & b are correct
221. A computer stored instruction in:
a) English language
b) Decimal number system
c) Octal number system
d) Binary number system
222. An input unit of a computer communicate
a) between operate and computer
b) between memory with printer
c) between cpu with monitor
d) between output and computer
223. Assembler is:
a) personal
b) programme
c) language
d) none of the above
224. If a current is a passing through the conductor the magnetic field induced depends
on which law:
a) laplaces law
b) biotsavarts law
c) faradays law
d) none of the above
225. In welding scatter is:
a) scattering of small partials around a finished weld
b) small holes on the welded structure
c) depositing of excess weld
d) none of the above is correct
226. A circuit carrying resistance, inductor, capacitor, across the circuits each carring low,
when the circuit is shorted in inductor then what is the value of capacitor:
a) 10v
b) 10 root 2
c) 10 root 2v
d) .28v
227. Electric are welding
a) it emits ultraviolet
b) infrared rays at high current flow
c) poisonous gas
d) all above are correct
228. soldering of Al alloy differs from other metal
a) low temp setting
b) very high temp, setting
c) no flux is used
d) flux is applied with solder
229. For dye penetrant test mark the correct statement:
a) large penetrating time larger crack
b) small penetrating time smaller crack
c) larger penetrating time smaller detects
d) all the above are correct
230. In X-rays:
a) if thickness is more the blacking is less long on the film
b) thickness of metal as referred to hose density
c) sensitivity of the radiography is determined by TQT
d) all of the above
231. Mark the correct statement
Computers
Objective Questions:
1. A computer in a/an
a) mechanical device
b) electrical device
c) electronic device
d) electromechanical device
2. A flow chart is a
a) step wise representation of a programme
b) a systematic pictorial representation of a programme
c) is a kind of programme written in high level language
d) either a & b
3. In order to drew a flow chart we used this symbol
a) for input/output
b) for processing
c) for start/setup
d) for decision making
4. A digital computer can be operated with
a) only numerical data
b) only non numerical data
c) both numerical and non numerical data
d) neither numerical nor non numerical data
5. Algerithm is a:
a) pictorial representation of a programme
b) a stepwise systematic representation of a programme
c) high level language to represent a programme systematically
d) assembly language to represent a programme systematically
6. An integrated circuit is
a) a complicated circuit
b) Microcomputer
c) Mainframe
d) Supercomputer
15. Main difference between PC/ATI and PC/XT are:
a) PC/AT has much more memory than PC/XT
b) PC/AT has much more speed than PC/XT
c) PC/AT has multi terminal facility and PC/XT has only single terminal facility
d) PC/XT has multi terminal facility and PC/AT has single terminal facility
16. Binary equivalent of 0.625
a)
0.010102
b)
(0.101)2
c)
0.11002
d)
0.010112
17. If the inputs of a gate are A and B and its output is A+B the gate is:
a) OR gate
b) AND gate
c) X-OR gate
d) X-NOR gate
18. The given truth table is for
A
B
C
1
1
1
0
0
1
0
1
0
1
0
0
a) XOR gate
b) NOR gate
c) NAND gate
d) OR gate
19. 2 complement of the binary digit is
a) 01
b) 1
c) 10
d) 0
20. XOR gate is:
a) a parallel switching circuit with exclude condition
b) series switching circuit with exclude condition
c) parallel switching circuit
d) series switching circuit
b) write memory
c) both a & b
d) none of the above
30. EPROM can be erased by
a) sodium light
b) uv rays
c) Electrical pulses
d) Either UV rays or electrical pulses
31. The fastest memory of the following
a) RAM
b) ROM
c) Cache
d) Hard disk
32. The main memory of a computer is located in
a) the hard disc
b) compact disk
c) floppy disk
d) none
33. ROM is
a) volatile semi conductor memory
b) non volatile semi conductor memory
c) magnetic memory
d) all of the above
34. The processing of the CPU is in the order of
a) millisecond
b) microsecond
c) nanosecond
d) megasecond
35. DRGM is
a) Semi conductor memory
b) Volatile memory
c) Has to be coefficiated with the data after a certain interval of time
d) All of the above
36. 1KB is equal to
a) 1000 bytes
b) 2 bytes
c) 1000 MB
d) none of the above
37. A nibble is equal to
a) 8 bits
b) 4 bits
c) 2 bits
d) 16bits
38. The fastest component of the computer is
a) CPU
b) Computer memory
c) Storage devices
d) Input/output devices
39. Locate the odd man out
a) hard disk
b) floppy disk
c) magnetic tape
d) compatt disk
40. Compact disk is a
a) semi conductor device
b) magnetic device
c) optical device
d) none of the above
41. Locate the odd man out
a) OBR
b) OMR
c) OCR
d) MICR
42. Floppy diskett is a :
a) EPROM
b) RAM
c) EEPROM
d) Flexible storage media
43. The slowest of the following is
a) hard disk
b) floppy disk
c) CD
d) Magnetic tape
44. CPROM is released by
a)
b) infrared light
c) electrical package
d) by appropriate programming only
45. Vol storages are those from where data are lost
a) when the programme is over
b) output device
c) input/output device
d) none of the above
54. Locate the odd man out
a) Dot matrix printer
b) Inkjet printer
c) Chain printer
d) Drum printer
55. Optical scanner is a
a) input device
b) output device
c) input/output device
d) none of the above
56. A software is a
a) set of programmes
b) set of instructions
c) all of the above
d) none of the above
57. Disk operating system is
a) a system software
b) software environment
c) software utility package
d) a high level language
58. Computer virus is a
a) software programme
b) hardware programme
c) machine language
d) assembly language
59. Assembly language is
a) low level language
b) high level language
c) machine language
d) all generation language
60. Which of the following language used memories
a) machine language
b) assembly language
c) high level language
d) all generation language
61. Which of the following is a scientific language
a) COBOL
b) ADA
c) FOPTRAN
d) BASIC
62. Which of the following is not a language
a) FOXPROT
b) LISP
c) C
d) VISUAL C++
63. Pick the odd man out
a) DOS
b) UNIX
c) WIN-95
d) DBASE
64. A package is a
a) software
b) set of instruction
c) a programme
d) all of the above
65. Windows 3.1 is a/an
a) operating system
b) operating environment
c) package
d) language
66. Which of the following is not a high level language
a) basic
b) C
c) Assembly
d) Cobol
67. Which of the following is not a high level computer language
a) windows
b) visual c++
c) coral
d) pascal
68. DOS stands for
a) data operating system
b) disk operating system
c) diode operating system
d) none of the above
69. Unix is a
a) a software
b) a programme
c) multiuser operating system
d) all of the above
70. Assembler is
a) a software
b) a translator
c) a programme
d) all the above
72. High level language are
a) machine dependent
b) machine independent
c) language in which programme is done in 1 & 0
d) b & c
73. Interpreter in computer field is a
a) software
b) floppy
c) hardware
d) the special electronic circuit which translate high level to low level
74. Internet system is based on
a) WAN system
b) LAN system
c) Mainframe computer system
d) Many computers connected to a other computer
75. GUI stands for
a) graphical user interface
b) graphical user internet
c) graph & user interface
d) graph & user internet
76. Y2K problem is a
a) software problem
b) hardware problem
c) data problem
d) all the above
77. Virus affects
a) hardware
b) software
c) both a & b
d) none of the above
78. Anti virus software is
a) dreaded software
b) software to scan & remove software
c) package
d) none of the above