Professional Documents
Culture Documents
Study of Nonminimum Phase Systems
Study of Nonminimum Phase Systems
Introduction
Mathematical models of most physical systems are characterized by differential equations [10]. The differential equation describing a linear time-invariant system (i.e., coefficients of the describing differential equations are constants and not functions of time)
can be re-modeled into the transfer function representation for the transient response
or frequency response analysis of SISO linear systems. The transfer function of a linear
time-invariant system is defined to be the ratio of the Laplace transform of the output
variable to the Laplace transform of the input variable under the assumption that all
initial conditions are zero.Thus if C(s) is the Laplace transform of the output and R(s)
is the Laplace transform of the input, then the transfer function of the SISO system is
given by
C(s)
b0 sm + b1 sm1 + ... + bm
= G(s) =
;m < n
R(s)
a0 sn + a1 sn1 + ... + an
(1.1)
1.2
1.2.1
Characteristics of Poles
The nature of g(t) is dependent on the poles of the transfer function G(s) which are the
roots of the characteristic equation.[11] These roots may be real and complex and may
have multiplicity of various orders. Certain observations can be made for the nature of
terms contributed by the types of roots with non zero real parts as follows: (a) All the roots which have nonzero real parts contribute response terms with a
multiplication factor of et . Also if < 0, i.e., the roots have negative real parts,
the response terms vanish as t and if > 0, i.e., the roots have positive real parts
the response terms increase without bound.
(i) For single root at s = , the nature of response is Aet .
(ii) For roots of multiplicity k at s = , the nature of response is (A1 + A2 t +
... + Ak tk1 )et
(iii) For complex conjugate root pair at s = + / j, the nature of response is
Aet sin(t + b)
(iv) For complex conjugate root pairs of multiplicity k at s = +/j, the nature
of response is [A1 sin(t + b1 ) + A2 tsin(t + b2 )... + Ak tk1 sin(t + bk )]et
(b) The above observation leads to the general conclusion regarding stability: (i) If all the roots of the characteristic equation have negative real parts, then
the impulse response is bounded and eventually decreases to zero.
(ii) If any root of the characteristic equations has a positive real part, g(t) is
unbounded and the system is therefore unstable.
1.2.2
The phase response of the system with transfer function G(s) will depend on both the
poles and zeros of the transfer function.[12]
(a) Minimum phase systems are those whose transfer functions have all poles and
zeros in the left half of the s-plane i.e., the poles and zeros have negative real
parts. In this case, the phase response of the system is restricted within 0 degrees
to 90 degrees and the amplitude response is a constant or unique for a particular
frequency as is increased from 0 to inf. In other words the transfer function has
the least (minimum) phase angle range for a given magnitude curve and there is a
unique relationship between the phase and magnitude curves.
(b) All pass systems are those whose transfer functions are having a pole-zero pattern
which is anti-symmetric about the imaginary axis i.e., for every pole in the left
half of the s plane there is a zero in the mirror image position. In this case, the
phase response varies from 0 degrees to 180 degrees as is increased from 0 to
inf while the amplitude response is unity.
(c) Non minimum phase systems are those whose transfer functions have one or more
poles or zeros in the right half of the s plane.The range of phase angle of any non
minimum phase transfer function is greater than 90 degrees. Unlike a minimum
phase system where the transfer function can be uniquely determined from the
magnitude curve alone, the non minimum phase system transfer function cannot
be determined. Also, non minimum phase systems are slow in response because of
their faulty behavior at the start of the response.
1.3
s2
s+4
+ 2s + 4
The step response plots and the bode plot of the above plant is as shown in Fig.2.1.
1.4
1.2
10
1
Plant output
Magnitude (dB)
Bode Diagram
10
20
Phase (deg)
30
90
45
Input
Output
0.8
0.6
0.4
0.2
45
90
2
10
10
10
10
0
0
10
10
time(s)
Frequency (rad/sec)
(b) Non Minimum Phase Plant(NMP): The transfer function of a second order
system with one zero in right hand plane is chosen as below:
p(s) =
s2
s + 4
+ 2s + 4
The step response plots and the bode plot of the above plant is as shown in Fig.2.2.
Magnitude (dB)
10
0.8
30
180
135
90
45
0
45
90
2
10
Plant output
1.2
Phase (deg)
Bode Diagram
10
20
Input
Output
0.6
0.4
0.2
0
10
10
10
0.2
0
10
10
time(s)
Frequency (rad/sec)
1.4
Conclusion
In this chapter minimum phase and non minimum phase systems were studied and
simulations carried out to show their characteristics.