Professional Documents
Culture Documents
Set 10
Set 10
OBJECTIVE:Q1.
Q2.
Q3.
Q4.
Q5.
Q6.
Q7.
Q8.
Q9.
Q10.
Q11.
Q12.
Q13.
Q14.
Q15.
Q16.
Q17.
Q18.
Q19.
Q20.
Q21.
Q22.
Which type of hammer used for stretching a piece of stock in the direction of it is width using
1. Ball-peen hammer
2. Cross-peen hammer
3. Straignt peen hammer
4. None
In case of straight peen hammer, which has peen end
1. At right angle to the hammer handle
2. Parallel to axis of the handle
3. Both 1 and 2 correct
Excessive heat at the time of grinding appearing on the blade indicated by
1. Red colour
2. Blue colour
3. Yellow colour
4. None
Which type of wrench used for turning check or Jam Nut
1. Tool-post wrench
2. Square box wrench
3. Both1 and 2
4. None
In case of square box wrench the square opening is make at an angle
1. 21
2. 22
3. 33
4. 44
Which type of wrench is used on Nut requiring great leverage or place where a T-socket wrench can not be used
1. Pin hook spanner wrench
2. Adjustable hook spanner
3. Both 1 and 2 correct
4. None
Which type of wrench is for turning cylinder part or pipe
1. Strap wrench
2. Allen wrench
3. Both 1 and 2 correct 4. None
What is thickness of hacksaw blade
1. Thin steel about 0.027 inch
2. Thin steel less than 0.027 inch
3. Thin steel more than 0.027 inch
4. None
How is the length of hack saw blade determined
1. Distance from the Tip to Tip
2. Distance from center of hole to opposite centre of hole
3. Both 1 and 2 correct
4. None
What kind of steel material hacksaw blade made
1. High grade of steel (Tool steel)
2. As in 1 high speed steel
3. AS in 2 tungsten alloy steel
4. As in 3 cupper alloy
For what kind of material are flexible hack saw blade preferred
1. Tin
2. Copper
3. Aluminimum
4. All
The size of teeth on a hack saw blade in referred to as
1. Pitch
2. Diameter
3. Depth
4. All
On which kind of Job should a hack saw blade with 14 T.P.I. used
1. Machine steel
2. cold- rolled steel
3. Structural steel
4. All
Which type of blade used for sheet metal more than 18 gage thickness
1. 14 T.P.I.
2. 18 T.P.I.
3. 24 T.P.I.
4. 32 T.P.I.
Which maximum stroke per minute should be a hacksaw be used
1. 60 Stroke
2. 80 Stroke
3. 90 Stroke
4. All
How the length of a file measure
1. Distance from the heel to the T.I.P.
2. Distance from the Tang to T.I.P.
3. Both 1 and 2 correct
4. None
What is included angle of sharp edge being knife file
1. Approximately 100
2. Approximately 200
3. Approximately 250
4. Approximately 200
Which type of file used for die maker and also by watch and clock maker
1. Knife file
2. Warding file
3. Needle file
4. None
Which type of filing is the operation of pushing and pulling a file sidewise across the work
1. Draw filing
2. Crossing filing
3. Both 1 and 2 correct 4. None
Which type of chisel used mostly to chip grooves and key way
1. Flat clod chisel
2. Cap chisel
3. Round nose chisel
4. Diamond point chisel
Type colour code of aviation snip that cut to the right
1. Yellow
2. Red
3. Black
4. None
To cut small tubing conduit and sheet metal less than 18 gage thickness, the hacksaw blade should have
1. 14 T.P.I
2. 18 T.P.I.
3. 24 T.P.I.
4. 32 T.P.I.
Q23.
Q24.
Q25.
Q26.
Q27.
Q28.
Q29.
Q30.
Q31.
Q32.
Q33.
Q34.
Q35.
Q36.
Q37.
Q38.
Q39.
Q40.
Q41.
Q42.
Q43.
Q44.
Q45.
Q46.
Q47.
Q48.
Q49.
Q50.
Q51.
Q52.
Q53.
Q54.
Q55.
Q56.
Q57.
Q58.
Q59.
Q60.
Q61.
Q62.
Q63.
Q64.
Q65.
Q66.
Q67.
Q68.
Q69.
Q70.
Q71.
Q72.
Q73.
Q74.
Q75.
Q76.
Q77.
Q78.
Q79.
Q80.