Professional Documents
Culture Documents
Dual Operational Amplifier: Semiconductor Technical Data
Dual Operational Amplifier: Semiconductor Technical Data
Low Voltage Noise: 4.5 nV/ Hz High Gain Bandwidth Product: 15 MHz High Slew Rate: 7.0 V/s Low Input Offset Voltage: 0.3 mV Low T.C. of Input Offset Voltage: 2.0 V/C Low Distortion: 0.002% Excellent Frequency Stability Dual Supply Operation
8 1
8 1
PIN CONNECTIONS
VCC Output 2
MAXIMUM RATINGS
Rating Supply Voltage (VCC to VEE) Input Differential Voltage Range (Note 1) Input Voltage Range (Note 1) Output Short Circuit Duration (Note 2) Operating Ambient Temperature Range Operating Junction Temperature Storage Temperature Maximum Power Dissipation (Notes 2 and 3) Symbol VS VIDR VIR tSC TA TJ Tstg PD Value +36 30 15 Indefinite 40 to +85 +150 60 to +150 500 C C C mW Unit V V V
Output 1
Inputs 1
3 2 6
Inputs 2
5
VEE
(Top View)
ORDERING INFORMATION
Device LM833N LM833D TA = 40 to +85C Operating Temperature Range Package Plastic DIP SO8
NOTES: 1. Either or both input voltages must not exceed the magnitude of VCC or VEE. 2. Power dissipation must be considered to ensure maximum junction temperature (TJ) is not exceeded (see power dissipation performance characteristic). 3. Maximum value at TA 85C.
Rev 0
LM833
ELECTRICAL CHARACTERISTICS (VCC = +15 V, VEE = 15 V, TA = 25C, unless otherwise noted.)
Characteristic Input Offset Voltage (RS = 10 , VO = 0 V) Average Temperature Coefficient of Input Offset Voltage RS = 10 , VO = 0 V, TA = Tlow to Thigh Input Offset Current (VCM = 0 V, VO = 0 V) Input Bias Current (VCM = 0 V, VO = 0 V) Common Mode Input Voltage Range Large Signal Voltage Gain (RL = 2.0 k, VO = 10 V Output Voltage Swing: RL = 2.0 k, VID = 1.0 V RL = 2.0 k, VID = 1.0 V RL = 10 k, VID = 1.0 V RL = 10 k, VID = 1.0 V Common Mode Rejection (Vin = 12 V) Power Supply Rejection (VS = 15 V to 5.0 V, 15 V to 5.0 V) Power Supply Current (VO = 0 V, Both Amplifiers) Symbol VIO VIO/T IIO IIB VICR AVOL VO+ VO VO+ VO CMR PSR ID Min 12 90 10 12 80 80 Typ 0.3 2.0 10 300 +14 14 110 13.7 14.1 13.9 14.7 100 115 4.0 Max 5.0 200 1000 +12 10 12 8.0 dB dB mA Unit mV V/C nA nA V dB V
kHz % dB
600
400
200
0 50
150
0 55
25
100
125
LM833
Figure 3. Input Bias Current versus Supply Voltage
800 I IB , INPUT BIAS CURRENT (nA) IS , SUPPLY CURRENT (mA) TA = 25C 600 10 8.0 6.0
IS
RL = TA = 25C
VO
+
VEE
400
4.0 2.0 0
200
5.0
20
5.0
20
105
100
90
95
90 55
25
100
125
80 5.0
20
15
Gain
135
5.0
180 10 M
0 55
25
100
125
LM833
Figure 9. Gain Bandwidth Product versus Supply Voltage
GBW, GAIN BANDWIDTH PRODUCT (MHz) 30 f = 100 kHz TA = 25C 20 10
8.0
Falling Rising
10
4.0
Vin
VO RL
0 5.0
20
2.0 55
100
125
Falling Rising
VO RL
20
10
100
10 M
100 k
+Vsat
14
Vsat
LM833
Figure 15. Power Supply Rejection versus Frequency
PSR, POWER SUPPLY REJECTION (dB) VCC = +15 V VEE = 15 V TA = 25C
VCC ADM
140 120 100 80 60 40 20 0 100 +PSR = 20 Log PSR = 20 Log 1.0 k PSR
VO VEE
VO VCM ADM V0
+PSR
( (
) )
1.0 M 10 M
5.0
0.01
VO = 1.0 Vrms
2.0
0.001 10
1.0 10
100
10 k
100 k
10
100
10 k
100 k
1.0 1.0
10
100
1.0 k
10 k
100 k
1.0 M
LM833
Figure 21. Inverting Amplifier
VO , OUTPUT VOLTAGE (5.0 V/DIV) VO , OUTPUT VOLTAGE (5.0 V/DIV) VCC = +15 V VEE = 15 V RL = 2.0 k CL = 0 pF AV = 1.0 TA = 25C
LM833
OUTLINE DIMENSIONS
N SUFFIX PLASTIC PACKAGE CASE 62605 ISSUE K
8 5 NOTES: 1. DIMENSION L TO CENTER OF LEAD WHEN FORMED PARALLEL. 2. PACKAGE CONTOUR OPTIONAL (ROUND OR SQUARE CORNERS). 3. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. DIM A B C D F G H J K L M N MILLIMETERS MIN MAX 9.40 10.16 6.10 6.60 3.94 4.45 0.38 0.51 1.02 1.78 2.54 BSC 0.76 1.27 0.20 0.30 2.92 3.43 7.62 BSC 10_ 0.76 1.01 INCHES MIN MAX 0.370 0.400 0.240 0.260 0.155 0.175 0.015 0.020 0.040 0.070 0.100 BSC 0.030 0.050 0.008 0.012 0.115 0.135 0.300 BSC 10_ 0.030 0.040
B
1 4
F
NOTE 2
A L
C T
SEATING PLANE
J N D K
M
G 0.13 (0.005) T A
M
D
5
E
1 4
0.25
h B C e A
SEATING PLANE
X 45 _
NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. DIMENSIONS ARE IN MILLIMETERS. 3. DIMENSION D AND E DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 PER SIDE. 5. DIMENSION B DOES NOT INCLUDE MOLD PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.127 TOTAL IN EXCESS OF THE B DIMENSION AT MAXIMUM MATERIAL CONDITION. DIM A A1 B C D E e H h L MILLIMETERS MIN MAX 1.35 1.75 0.10 0.25 0.35 0.49 0.18 0.25 4.80 5.00 3.80 4.00 1.27 BSC 5.80 6.20 0.25 0.50 0.40 1.25 0_ 7_
L 0.10 A1 0.25 B
M
C B
LM833
Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. Typical parameters which may be provided in Motorola data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including Typicals must be validated for each customer application by customers technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. How to reach us: USA / EUROPE / Locations Not Listed: Motorola Literature Distribution; P.O. Box 20912; Phoenix, Arizona 85036. 18004412447 or 6023035454 MFAX: RMFAX0@email.sps.mot.com TOUCHTONE 6022446609 INTERNET: http://DesignNET.com
JAPAN: Nippon Motorola Ltd.; TatsumiSPDJLDC, 6F SeibuButsuryuCenter, 3142 Tatsumi KotoKu, Tokyo 135, Japan. 038135218315 ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park, 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 85226629298
*LM833/D*
This datasheet has been download from: www.datasheetcatalog.com Datasheets for electronics components.