Professional Documents
Culture Documents
Model Tuning Atoll PDF
Model Tuning Atoll PDF
INTERNAL
Product name
RNP
Product version
1.2
Confidentiality level
INTERANL
Total 85 pages
Prepared by
Reviewed by
Reviewed by
Approved by
Date
Date
Date
Date
Zang Liang
2008-11-17
2008-12-10
Page1 , Total85
INTERNAL
Revision Records
Date
2008-1205
2008-1216
2009-3-25
Version Description
Reviewer
1.0
Initial transmittal
Li Peng, Lu Peng,
Zang Liang
Yangfan
1.1
Qin Yan
1.2
Chen Fazhi
2008-12-10
Author
Page2 , Total85
INTERNAL
Contents
2.1 About Model Tuning.................................................................................................................................................9
2.2 Flow for Model Tuning...........................................................................................................................................10
3.1 About SPM.............................................................................................................................................................12
3.1.1 Basic Formula...................................................................................................................................................12
3.1.2 Distance and Visibility Between Tx Antenna and Rx Antenna .......................................................................12
3.1.3 Effective Height of Tx Antenna........................................................................................................................13
3.1.4 Effective Height of Rx Antenna.......................................................................................................................14
3.1.5 LOS Amendment for Mountainous Regions....................................................................................................14
3.1.6 Calculating Diffraction Loss.............................................................................................................................14
3.1.7 Clutter loss........................................................................................................................................................14
3.2 Procedure for Tuning SPM.....................................................................................................................................15
3.2.1 Setting Up a Model Tuning Project..................................................................................................................16
3.2.1 Setting Up Propagation Model.........................................................................................................................20
3.2.2 Setting Transmitter...........................................................................................................................................25
3.2.3 Importing and Adjusting Data..........................................................................................................................31
3.2.4 Model Tuning...................................................................................................................................................46
3.2.5 Proposals on SPM Tuning................................................................................................................................51
3.2.6 Analyzing Result and Verifying Model............................................................................................................54
4.1 Configuring Parameters of Volcano Model............................................................................................................59
4.1.1 Configuring Parameters of Volcano Macrocell Model.....................................................................................60
4.1.1 Configure Parameters of Volcano Microcell Model.........................................................................................67
4.1.2 Configuring Parameters of Volcano Minicell Model........................................................................................74
4.2 Tuning Volcano Models..........................................................................................................................................82
4.2.1 Tuning Process..................................................................................................................................................83
4.2.1 Checking and Analyzing Tuning Result...........................................................................................................84
2008-12-10
Page3 , Total85
INTERNAL
Figures
Model Tuning Flow.........................................................................11
Four weighting methods for calculating clutter loss in SPM..............15
Importing data of Clutter class.......................................................17
Importing data of altitude .............................................................18
Imports data of clutter heights.......................................................18
Importing data of vectors (1)..........................................................19
Importing data of vectors (2)..........................................................19
Antenna properties........................................................................20
Importing antenna file....................................................................20
Setting up propagation model........................................................21
Properties of SPM..........................................................................22
Setting SPM parameters.................................................................22
Configuring parameters of Clutter tab for SPM................................24
Configuring parameters of Calibration tab for SPM..........................25
Importing head file........................................................................27
Global parameters of transmitters..................................................27
Configuring transmitter propagation models ..................................28
Setting up new site........................................................................29
Setting up transmitter...................................................................29
Properties of new transmitter.........................................................30
Configuring pilot power..................................................................31
Setting up CW measurements.........................................................32
New CW measurement path............................................................33
Interface after importing data........................................................33
2008-12-10
Page4 , Total85
INTERNAL
Importing CW measurement...........................................................34
Importing a text file.......................................................................34
General tab displayed after importing CW measurement data..........35
Changing measurement line...........................................................36
CW measurement setup.................................................................36
Setting CW measurement manually.................................................37
Filtering measurement data...........................................................38
Displaying measurement data........................................................39
Properties of the file for tuning coordination system.......................40
Before translating location in map..................................................41
Original coordinates of reference point...........................................42
After translating location in map....................................................43
Coordinates of reference point after translation..............................44
Frequency Difference Setting.........................................................45
Parameters of SPM to be tuned.......................................................47
Setting filtering conditions for SPM tuning......................................48
Tuning SPM (1)..............................................................................49
Tuning SPM (2)..............................................................................49
Automatic Calibration....................................................................51
Select parameters for calibration....................................................51
Statistics report after tuning..........................................................55
Measurement parameters of tuned model.......................................56
Comparison curve..........................................................................57
Properties window of measurement data of tuned model.................57
Error distribution...........................................................................58
Volcano models displayed in U-Net..................................................60
Parameters in General Tab for Volcano Macrocell model...................61
Parameters in Map data tab for Volcano Macrocell model.................62
Parameters in Clutters Tab for Volcano Macrocell model...................63
Parameters in vectors tab for Volcano Macrocell model....................64
2008-12-10
Page5 , Total85
INTERNAL
2008-12-10
Page6 , Total85
INTERNAL
2008-12-10
Page7 , Total85
INTERNAL
Tables
Frequency differences for GSM900 in different propagation
environments................................................................................45
Frequency differences for DCS1800 in different propagation
environments................................................................................45
Default values of SPM coefficients..................................................46
Value range of K parameters..........................................................50
Typical values of clutter losses.......................................................52
Abstract
This guide introduces flow and principle for model tuning. The operation procedures for SPM and
Volcano model tuning are described based on U-NET tool. There are some rules for guaranteeing
correct tuning results. The U-NET tool software version is U-NET 2.2.1(Build 2613) in this book.
Full Spelling
CW
SPM
LOS/NLOS
Continuous Wave
standard propagation model
Line of sight/No Line of sight
2008-12-10
Page8 , Total85
INTERNAL
Overview
The propagation model lays a foundation for the cell planning of a mobile communication network.
The accuracy of the propagation model determines whether the cell planning is reasonable and
whether operators can meet the requirements of users through cost-effective and rational
investments. Therefore, it is necessary to tune the propagation model in order to obtain the wireless
propagation model that complies with the actual environment of the specific area, improve the
accuracy of the coverage prediction and lay a solid foundation for network planning. This document
introduces rationales for propagation model tuning, methods and principles for propagation model
tuning based on the U-Net tool. The methods and principles include method and flow for processing
the data obtained in the CW test and tuning the propagation model by using the data in the U-Net
tool and some rules for guaranteeing correct tuning results.
This guide includes main chapters as below.
Chapter 2: Introduce the flow and basic knowledge for model tuning.
Chapter 3: Describe the process for SPM model tuning in a detail.
Chapter 4: Introduce how to tune Volcano model.
Page9 , Total85
INTERNAL
Actual measurement and statistics method based on large amount of test data and
empirical formulae
The radial tracking model integrated into the planning software, which can be put into commercial
use, such as Volcano model, WaveSight model and WinProp model, and they are the representations
of propagation model research through the theoretical analysis method, but this type of model
requires a high precision (at least 5 m precision), including 3D digital map of the building
information. Accuracy of model prediction is closely related to the precision and accuracy of the
digital map. Those factors that affect the propagation of radio signals such as moving vehicles
cannot be considered in the current theoretical analysis method, but the general theoretical analysis
method requires some approximation and simplification of the propagation environment, thus
causing certain errors. At present, the propagation model based on the theoretical analysis method
has not been applied in large scale.
In the actual measurement and statistics method for the propagation model, the most famous
statistics model is Okumura model. This model is a propagation model represented by curves and
was built by Okumura based on a large amount of test data collected in Japan. On the basis of the
Okumura model, the regression method is used to fit out resolution empirical formulae to facilitate
computation. These empirical formulae include the Hata model formula, which is applicable to the
GSM900 macro cell, and the COST 231-Hata formula, which is applicable to the GSM1800 macro
cell. These empirical formulae also include the COST 231 Walfish-Ikegami model formula, which is
applicable to the microcell, and the Keenan-Motley formula, which is used in the indoor propagation
environment. These formulae are complex and errors may occur as against the actual environment.
2008-12-10
Page10 , Total85
INTERNAL
2008-12-10
Page11 , Total85
INTERNAL
SPM Tuning
SPM supports using different constant K1 and distance coefficient K2 for LOS/NLOS
and near/far region.
Due to the previous new features, SPM is more flexible and applies to more scenarios. You can tune
SPM according to the data of CW measurement, namely, the adjustment of parameters.
Lmod el = K 1 + K 2 log ( d ) + K 3 log ( HTxeff ) + K 4 Diffractio n loss + K 5 log ( d ) log ( HTxeff ) + K 6 ( H Rxeff ) + K clutter f ( c
Wherein,
K2: the multiplier (distance factor). It shows how the field strength changes as the
distance changes.
K3: the multiplier of log(HTxeff). It represents the variation of field strength as the height
of Tx antenna changes.
K6: multiplier of H Rxeff . It represents the variation of field strength as the height of Rx
antenna changes.
H Rxeff
Page12 , Total85
INTERNAL
Visibility
According to terrain and clutter high, SPM judges whether the receiver is in the light of sight (LOS)
range. If you do not use the clutter height layer, SPM calculates LOS with the terrain height map
only. If you use the clutter height layer, SPM calculates LOS with the terrain and clutter height
maps. If the receiver is in the sight of LOS, SPM use (K1,K2)LOS; otherwise, SPM uses
(K1,K2)NLOS.
as below:
Spot Ht
Abs Spot Ht
U-Net supports a new method to calculate effective height of Tx antenna, called "Enhanced slope at
receiver".
The methods of "1-Height above average profile" and "0-Height above ground" apply to plain region
while other methods are for mountainous regions. This does not mean that the methods for
mountainous regions do not apply to plain regions. The best method is to adjust these parameters and
to produce a most suitable tuning result.
2008-12-10
Page13 , Total85
INTERNAL
H 0 Rx : the ground height (ground elevation) above sea level at the receiver (m).
H 0Tx : the ground height (ground elevation) above sea level at the transmitter (m).
and H Txeff
Deygout
Epstein-Peterson
Millington
For the urban areas or the urban areas with rural areas, the operator can use Deygout and EpsteinPeterson (these two methods also apply to mountainous regions).
f ( clutter ) = Li w i
i =1
Wherein,
n: number of spots to be considered in the lateral section. These spots are distributed
according to the accuracy of lateral section.
2008-12-10
1
n
Page14 , Total85
INTERNAL
wi =
di
n
d
j =1
d i = D d i' . The d'i is the distance between the receiver and the ith spot. The D is the
maximum defined distance.
log i + 1
D
log
+ 1
j =1
D
wi =
e
n
di
D
1
dj
D
j =1
Figure 1.1 Four weighting methods for calculating clutter loss in SPM
w i=f(di)
Uniform w eighting function
Triangular w eighting function
Loragithmic w eighting function
Exponential w eighting function
wi
di
2008-12-10
Page15 , Total85
INTERNAL
CW data measurement and filtering processing are introduced in the guide Radio Propagation
Feature Test. Here shows the process of data input. Before importing head files, proceed as below:
Step 2 Set up a new project.
Step 3 Import digital maps.
Step 4 Set the coordination system.
Step 5 Import antenna pattern
The contents from step 1 to step 4 are simply described here and can be known detailedly in the UNet Operation Manuel.
Step 6 Set up the model to be tuned.
----End
After importing head files, compare the related setting values with contents in head files.
If you select WGS84 UTM Zones coordination system, so you shall select WGS84/UTM
zones 50N.
If you select Asia-Pacific coordination system, so you shall select Beijing 1954/GaussKruger 20N.
The previous two coordination systems apply to the digital maps for Zhangzhou. The side
coordination system depends on the main coordination system, namely,
Page16 , Total85
INTERNAL
system for The Northern Hemisphere is usually marked with the letter N.
The following paragraphs describe how to import digital maps that are commonly used by Huawei.
For importing other types, see U-Net Usage Guide.
Clutter Map
Read the index file according to the saving path (usually clutter or DLU) of clutter map files. Select
Clutter class as shown in 3.2.1, and then click OK.
Figure 1.1 Importing data of Clutter class
Height Map
Read the index file in the saving path (usually height or DTM) where the height map file is saved. As
shown in 3.2.1, in Data type box, select Altitude, and then click OK.
2008-12-10
Page17 , Total85
INTERNAL
Read the index file in the saving path (usually Building or DHM) where the height map file is
saved. As shown in 3.2.1, in Data type box, select Clutter Heights, and then click OK.
Figure 1.3 Imports data of clutter heights
Vector Map
Read the index file in the saving path (usually Vector) where the vector map file is saved. As shown
in 3.2.1, in Data type box, select Vectors, and then click OK.
2008-12-10
Page18 , Total85
INTERNAL
By select the Embed in document right under the Geo drop-down list, you can choose to display
one or four types of maps. For the operations like modifying the properties of map, see the
corresponding manual.
Not all maps include the four data types. Import the corresponding maps according to the map
conditions and project's requests in actual operations.
Page19 , Total85
INTERNAL
For the properties of antenna, see the U-Net User Manual. If the current antenna is present in the
original antenna library, you do not need to re-import and you can use it directly.
Import the corresponding antenna file directly if there is. Select File > Import. In the File dialog
box, change the file type to "Planet Database". In the Planet data to be imported dialog box, import
the antenna index file (named index) in the Antenna box. Click OK, and then click OK. You can
see the imported antenna file in the Explorer window of U-Net.
Figure 1.2 Importing antenna file
Page20 , Total85
INTERNAL
an area.
Figure 1.3 Setting up propagation model
2008-12-10
Page21 , Total85
INTERNAL
2008-12-10
Page22 , Total85
INTERNAL
Before tuning propagation models, you shall configure the parameters in the Parameters tab,
detailed as below:
Diffraction
Method: select 1-Deygout by default.
K4: If there is not height information about clutter in the map and there is no great
undulation in the area, you are not recommended to adjust K4 and you can configure K4
to 0; otherwise, configure it to 1.
Other parameters
K5: use the default value.
K6: use the default value.
Kclutter: you can configure Kclutter to 0 in tuning; namely, you do not count clutter
loss. The CW test usually proceeds in outdoor open land, so there are inadequate spots.
As a result, the clutter loss is not adjusted according to recommendation. The default
value of clutter loss serves in simulation forecast, so the default Kclutter is 1.
Other parameters /hilly terrain correction: configure it to 1-yes only when the total
terrain is with great undulation (with a fall over 50 m); otherwise, configure it to 0-no.
Profile: use the default value.
Grid calculation: use the default value.
2008-12-10
Page23 , Total85
INTERNAL
If you use 2D digital map (20-meter solution or lower) without clutter height layer,
you can configure Use clutter heights to 0-No.
If you use 3D digital map (5-meter solution or higher) with clutter height layer and
you want to calculate diffraction loss with clutter height, you can configure Use clutter heights to
1-yes.
If you use 3D digital map (5-meter solution or higher) with clutter height layer and
you do not want to calculate diffraction loss with clutter height, you can configure Use clutter
heights to 0-No.
As previously described, if you configure Use clutter heights to 1, namely, you want to calculate the
diffraction with clutter height, you need configure K4 to 1, the default value.
Losses per clutter class: it refers to clutter losses. The CW test spots are all in open
2008-12-10
Page24 , Total85
INTERNAL
land, so you must configure all the clutter losses to 0 in model tuning. Do not adjust
clutter loss in model tuning. However, you need configure clutter loss to the
recommended value in simulation forecast.
When the test data is already imported, the test paths will be displayed in the CW measurement
path(s) to be used box.
LOS and NLOS: If you do not want to distinguish LOS and NLOS, you need select two buttons. If
you want to tune LOS or NLOS parameters respectively, you can select them respectively for tuning.
Antenna type
Page25 , Total85
INTERNAL
test.dat: the name of the file that saves test data for the site. If there are multiple test
files for a site, it is better to combine them into one. Now the data in the file can not be
automatically imported. Therefore you can delete it and re-import the data files when
test.
Test: the name of test site. You can change it accordingly. It is displayed after successful
import.
741790: the type of antenna used by the site. The antenna type is available before import
in U-Net. If it is unavailable, the U-Net automatically sets up the antenna type with the
same name. the pattern and gain are by default, so you need modify them accordingly. It
is recommended that you set up the corresponding antenna type before importing the
head file.
54: the transmit power of feeder port. When you configure it in U-Net, you can obtain
pilot power of NodeB by deducting antenna gain from EIRP. It is recommended as
below:
Transmit power of feeder port = output power of transmitter - total loss on the Tx feeder
- loss on feeder connectors + antenna gain + Rx antenna gain - total Rx loss. You shall
guarantee that the length of Tx feeder, the gain of Rx antenna, and Rx loss are configured
to 0. They are 0 by default.
0 0 0: the three 0's are the azimuth, down tilt, and squire size respectively. They are 0 for
omnidirectional antenna.
113.7509966: the eastern longitude degree of test site. Set it accordingly. Note that the
latitude degree is before the longitude degree. If it is southern latitude or western
longitude, put a minus symbol before the value.
Survey 0 GPS 0 0 0 0 hard: the last eight parameters of head file. They can be fixed.
The 1, 2, 3, 4, 6, 10, and 11 items are usually fixed. The method for obtaining the
template for head file the same as that for manual, and you can also make it.
When the head file is imported, the inside antenna type is not set up yet. The gain of the antenna of the type
automatically set up by U-Net is 0. As a result, the pilot power is the same as the transmit power of feeder
port, because the antenna gain is not automatically deducted. After the antenna pattern and gain are changed,
U-Net judges that the transmit power of feeder port is higher than actual power, so error occurs. Therefore
you need set up the antenna type before importing head file, and then check whether the pilot power equals to
the transmit power of feeder model minus antenna gain.
Page26 , Total85
INTERNAL
Step 1 In U-Net, click the Explorer pane, click the Data label, and right-click CW Measurement
(or select File > Import). In the drop-down list, select Import.
Step 2 A window is displayed, as shown in 3.2.2. Select the target head file and select its file type as
*.hd, and then open the file.
Figure 1.1 Importing head file
Step 3 In U-Net, click the Explorer pane, click the Data label, and right-click transmitter. Select
properties in the window, and the Transmitters properties window is displayed. Click the
Global parameter tab, as shown in 3.2.2. Configure frequency and keep the first carrier
unchanged as shown in 3.2.2.
Figure 1.1 Global parameters of transmitters
2008-12-10
Page27 , Total85
INTERNAL
Select the set model in the Propagation model drop-down list respectively. When there are multiple
sectors, you can set the model for each sector. You can configure the radius and resolution
respectively. The radius is the maximum distance from the test data to the site in model tuning.
Resolution is the accuracy of map. You do not need configure other parameters.
2008-12-10
Page28 , Total85
INTERNAL
Step 2 Set a Transmitter. In the similar way, you can configure parameters in the General tab on
the Transmitters new element properties. Input the name and site. The Dx and Dy are
usually configured to 0 m, because the location for recording data is the location of antenna.
Figure 1.1 Setting up transmitter
Step 3 In the Transmitter tab, input the losses of Tx feeder, antenna model, height, down tilts, as
shown in 3.2.2. Click OK.
2008-12-10
Page29 , Total85
INTERNAL
Step 4 In the navigation tree, right-click new Transmitter, and select Properties dialog box. Select
the Cell tab, and configure pilot power.
2008-12-10
Page30 , Total85
INTERNAL
Only the pilot power is used in model tuning, so other configurations have no impact on the tuning
result.
The pilot power minus loss of Tx feeder is the transmit power of feeder port. The transmit power of
feeder port plus antenna gain is EIRP.
You can configure the previous loss of Tx feeder to 0, and the pilot power shall
deduct loss of Tx feeder.
Some tests provide EIRP (such as there is only one head file *.hd), so you can
configure the loss of Tx feeder to 0 and configure the pilot power to EIRP minus antenna gain so
that the transmit power of feeder power is correct.
Other configurations, such as frequency and propagation mode, are the same as importing files. You
can refer to the previous section.
1Paste
Step 1 In the Explorer pane of U-Net, select the Data tab, right-click CW measurements, and
select New in the menu.
2008-12-10
Page31 , Total85
INTERNAL
Step 2 Configuring the parameters shown in 3.2.3 and then click OK.
Input the name of test file in the Name text box. You can name the test file
accordingly.
In the Transmitter area, input the name of site in the Name drop-down list and the
frequency in the Frequency spin box.
In the Receiver area, the Height is the height of test antenna. The Rx antenna is
usually mounted on the roof of vehicle, so the height depends on the height of vehicle. The default
height is 1.5 m. The gain and loss are usually 0. The value is already considered in the transmit
power of feeder port (note: the antenna gain and feeder loss of DTI is 4 dB, so they can counteract
each other).
In the Coordinates area, select the correct coordinates, otherwise serious error may
happen.
In the Measurements area, the unit is dBm by default. The X, Y, and M columns are
longitude, latitude, and measured level respectively. After you copy the DT data in an Excel table,
you can import the data into U-Net database by clicking the Paste button
2008-12-10
Page32 , Total85
INTERNAL
2Importing DT File
Step 1 In the Explorer pane of U-Net, select the Data tab, right-click CW measurements, and
select Import in the menu.
2008-12-10
Page33 , Total85
INTERNAL
Step 2 In the pop-up box, select the DT file. 3.2.3 shows an example of importing a text file.
Figure 1.1 Importing a text file
Step 3 In the General tab, define the parameters in the same way as the previous method.
2008-12-10
Page34 , Total85
INTERNAL
In the File area, as shown in 3.2.3, the 1st measurement line indicates the line to start
with. In 3.2.3, the line starts at the second one, so you input 2 in the 1st measurement line text box.
2008-12-10
Page35 , Total85
INTERNAL
Step 5 After you click the Setup button shown in 3.2.3, a CW measurement setup dialog box is
displayed, as shown in 3.2.3. For the * drop down list, select X (File) and Y (File)
respectively, and then click OK.
Figure 1.1 CW measurement setup
2008-12-10
Page36 , Total85
INTERNAL
This correspondence may also be achieved by clicking on the first line of the tale header shown in.
3.2.3. Usually you only need to match the longitude, latitude and measurement
Figure 1.2 Setting CW measurement manually
Distance range: The minimum distance is usually 100 m to 200 m. The principia for
configuring the maximum distance is about as large as twice of forecasted cell radius.
Range of field strength: The filtering conditions for signal strength depend on testers.
The range is usually 120 dBm to 40 dBm when test with E7476. The range is usually
110 dBm to 40 dBm when test with DTI.
Clutter: Filter the water and buildings which the actual test cannot cover. The test route is
in the outdoor land, and it may cover some spots that are defined by GPS, so you shall
filter these spots.
After you set filtering conditions, select the Delete points outside the filter check box in 3.2.3, and
click Apply to delete unnecessary points.
2008-12-10
Page37 , Total85
INTERNAL
When the measurement data is imported, you can change the mode and color to display the data in
the properties window. The detailed method is neglected herein. The data is displayed, as shown in
3.2.3.
2008-12-10
Page38 , Total85
INTERNAL
2008-12-10
Page39 , Total85
INTERNAL
Import files such as domo.b or demo.b in the GEO/clutter classes and Digital Terrain Model.
Right-click domo.b, and select Properties. A domo.b properties window is displayed, as shown in 3.2.3.
Figure 1.1 Properties of the file for tuning coordination system
Step 2 According to the deviation direction, deduct the deviations from or add the deviation to the
displayed data of X axis and Y axis, and the two deviations shall be the same. You may have
to adjust the data for multiple times until the actual route match the test data.
You cannot adjust the vector file with this method, so you need re-set up coordination system or
adjust the coordinates in the map file, and then re-import the data. Therefore the process is
complicated. If you use SPM, the deviation of vector lay has no impact on the accuracy of tuning, so
you can neglect it.
----End
2008-12-10
Page40 , Total85
INTERNAL
Select a reference point, such as the corner of a house. Click the point and record its coordinates
2008-12-10
Page41 , Total85
INTERNAL
Import the raster map with geocoding and minimize the deviation of CW measurement data and
actual route.
2008-12-10
Page42 , Total85
INTERNAL
Record the coordinates of longitude and latitude (Bx, By) of reference point after translation;
2008-12-10
Page43 , Total85
INTERNAL
9
10
Copy the CW measurement data to an Excel table. Add the deviation (dx, dy) to all the
----End
The second method is complicated, but it guarantees that the data matches the route. Therefore, it is
preferential. This guide describes Volcano model in the following part, so the vector layer is
necessary and is imported in the properties dialog box, so the first method does not work and the
second one works.
Page44 , Total85
INTERNAL
The U-Net provides three default values in editing areas at three frequency bands. Because path
losses vary in different propagation environments, 3.2.3 and 3.2.3 provide some frequency
differences of GSM900 and DCS1800 in different propagation environments. You can adjust these
differences according to your own requirements.
Table 1.1 Frequency differences for GSM900 in different propagation environments
Propagation Environment
Frequency Difference
Large cities
14.38 dB
Medium cities
11.35 dB
Suburbs
9.02 dB
7.34 dB
7.34 dB
Frequency Difference
Urban areas
1.549 dB
2008-12-10
Page45 , Total85
INTERNAL
Propagation Environment
Frequency Difference
Suburbs
1.21 dB
0.95 dB
0.95 dB
As shown in 3.2.3, if you select the Auto Setting DT Based Model check box, the U-Net sets the
propagation model of the transmitters for the new CW data to DT Based Model after the data is
imported; if you do not select the Auto Setting DT Based Model check box, the U-Net sets the
propagation model of the transmitters to the default propagation model. DT Based Model is the
name of the newly created propagation model.
Frequency
450 MHz
900 MHz
935 MHz
1805 MHz
2110 MHz
K1
4.3
12.1
12.6
22.0
24.3
K2
44.9
K3
5.83
K4
0.5
K5
6.55
K6
In the downtown areas of large and medium cities, increase K1 by 3 dB for 1805 MHz and 2110 MHz networks. Adjust the
K1 accordingly for suburban and rural areas.
2008-12-10
Page46 , Total85
INTERNAL
According to the method to configuration parameters in 3.2.1, check whether the parameters in each
tab are suitable. If they are suitable, click OK. Right-click the model, and select duplicate. Copy a
configured model and tune SPM based on the copied model.
Step 3 Select Data and Set Filtering Conditions
Right click the copied model and select calibration. A Calibration window is displayed, as shown in
3.2.4. Select the data set to be tuned, then select the Assisted Calibration.
2008-12-10
Page47 , Total85
INTERNAL
Note: Before doing calibration, you need to set the filtering conditions including distance, field, and
LOS/NLOS. Wherein, the distance and field are set in the measurement data properties dialog box
in 3.2.3.
If you want to tune K1 and K2 respectively according to LOS and NLOS, you can tune model by
selecting LOS and NLOS respectively; otherwise, select them simultaneously. For whether it is
necessary to tune LOS and NLOS parameters respectively, see 3.2.5LOS/NLOS.
Step 4 Tune Model
Click the right Calibration button in 3.2.4, and a Calibration window is displayed, as shown in
3.2.4. Select the variable and tune it by clicking Identify button. Once you select a variable, you can
see the correlation with the selected variable on the right.
2008-12-10
Page48 , Total85
INTERNAL
Click the Identify button so that U-Net tunes the multiplier of the selected variable. You can know
the amendment of the variable by checking correction. The relation between variables and K
parameters can be known from the basic formula in 3.1.1. The current value of K parameters equals
to the initial value plus amendment, as shown in 3.2.4.
Figure 1.2 Tuning SPM (2)
The most influential variable for tuning is log(D). You shall tune the multiplier K2 preferentially, and
the K1 will be automatically tuned.
2008-12-10
Page49 , Total85
INTERNAL
After tuning a parameter, check the correlation to calculate the current value of parameter (initial value plus amendment),
and check whether the value has exceeds the reasonable range. If the value has already exceeded the reasonable range, the
tuning fails.
Minimum
Maximum
Typical
K2
20
70
44.9
K3
20
20
5.83
K4
0.5
K5
10
6.55
K6
If the K parameters exceed the reasonable range, it is recommended to delete the tuned model and
re-duplicate a model based on the configured model to be tuned. Start tuning with the configured
model to be tuned. It is not recommended that you continue tuning by adjusting the K parameter
which has exceeded the reasonable range. Every tuning starts with the default values of SPM. If the
K parameter is within reasonable range after tuning, you can continue tuning by clicking the
Identify button.
When the K parameter is within the range by experience, the standard deviation is smaller than 8 by
experience and the statistics result is stable, you can finish tuning. If the result is unsatisfactory,
restart tuning with default values by adjusting parameters like effective height of antennas.
2008-12-10
Page50 , Total85
INTERNAL
Step 2 Select the CW test data and parameters for calibration in turn, and click Commit to complete
the setting, as shown in 3.2.4.
Figure 1.1 Select parameters for calibration
Page51 , Total85
INTERNAL
current stage due to limited collected data. The K1 and K2 are mandatory for model tuning, and
whether to tune other parameters depends on the following proposals.
If you test within a large range, the terrain undulates greatly. For example, the area is
mountainous. As a result, tuning K4 is recommended.
If you use high-resolution 3D maps with the height information about buildings, you
can calculate diffraction loss with the height information. Therefore, tuning K4 is recommended. In
this way, the obtained model will be more accurate.
Wet Land
Village
Town in Suburban
2008-12-10
Page52 , Total85
INTERNAL
Park in Urban
18
13
Ocean Area
18
Inland Water
High Buildings
20
Green land
Forest
10
Dense Urban
16
Common Buildings
13
7. LOS/NLOS
The proposals about LOS/NLOS are similar with these for 3.2.5K4.
If the used map lacks of height information about buildings and the terrain undulates
a little in the calculated range, the model cannot distinguish LOS and NLOS. Therefore,
distinguishing LOS/NLOS is not recommended.
If you test within a large range, the terrain undulates greatly. For example, the area is
mountainous. As a result, you can tune the model with LOS and NLOS respectively with two sets of
parameters.
If you use high-resolution 3D maps with height information about buildings, you can
tune the model with LOS and NLOS respectively with two sets of parameters.
For the later two cases, there must be enough spots (>200) for LOS and NLOS to guarantee accurate
tuning. Before tuning, collect statistics of spots for LOS and NLOS respectively (by clicking the
statistics button on the tuning properties tab) and check whether the number of spots meets the
requirement. If the spots for LOS or NLOS are inadequate, it is recommended not to distinguish
LOS/NLOS.
8. Near/Far region
SPM is a macro cell model applicable for a large range of cell radius, but engineers usually perform
tests in a range of 3 km. As a result, it is not to distinguish near and far region.
The range of K parameters and the requirement of standard deviation less than 8
mentioned previously are by experience and not absolute. For some special clutter, no
matter how you tune parameters, the tuning result still fails to meet the reasonable range
of K parameters and the requirement of standard deviation less than 8. A little deviation
is also acceptable.
2008-12-10
Page53 , Total85
INTERNAL
Model tuning is iterated process, sometimes it takes a long time. In addition, you do not
necessarily tune K parameters according to correlation or big to small. When you fail to
tune models ideally, you can try comprehensive tuning.
Checking with Statistics Report: SPM supports outputting model statistics report for
analysis, and this report includes the information like standard deviation.
Illustrating model tuning: By illustrating, you can clearly see the distribution of model
deviation so that you can evaluate the validity of model.
For example, in the diagram, the deviation on the roads is large, so you can judge that the
large deviation is due to test errors. You can delete these points and re-tune the model.
2008-12-10
Page54 , Total85
INTERNAL
2008-12-10
Page55 , Total85
INTERNAL
Calculate Signal Levels: calculate the level of signal from the transmitter according to
the selected model. After calculation, U-Net automatically collects overall statistics and
statistics of clutters, and then displays them.
Refresh geo data: refresh map information, such as clutter type and height.
Display statistics
2008-12-10
Page56 , Total85
INTERNAL
Step 5 Select Open the Analysis Tool, and a comparison curve is displayed, as shown in 3.2.6.
Figure 1.1 Comparison curve
The red curve stands for the measured value. The blue curve stands for the predicted value of tuned
model. You can see the distribution of model deviation with the suitability of two curves.
Select the display type and field as shown in 3.2.6. Error(P-M) stands for the error between predicted
value (P) and measured value (M). You can adjust the error range highlighted by different colors in
3.2.6; you can see the error distribution, as shown in 3.2.6.
2008-12-10
Page57 , Total85
INTERNAL
You can also predict coverage with the model and see the distribution and variation of predicted field. They indicate the
result of model tuning. The details are neglected here.
2008-12-10
Page58 , Total85
INTERNAL
Mini cell: the Tx antenna is between the Tx antenna of Macro cell and that of Micro cell.
For the second and third scenarios, Volcano models use ray tracing for calculation. For the macro
cell scenario, the Volcano model, similar with SPM, calculates LOS loss only.
You can install Volcano respectively. After installation, the Propagation Models list in the Modules
tab contains three models:
Volcano Macrocell
Volcano Microcell
Volcano Minicell
2008-12-10
Page59 , Total85
INTERNAL
2008-12-10
Page60 , Total85
INTERNAL
11
You can configure the parameters related to map used in model and map-related aspects, as shown in
4.1.1.
2008-12-10
Page61 , Total85
INTERNAL
Figure 1.1 Parameters in Map data tab for Volcano Macrocell model
Vertical analysis mode: it indicates whether the height information about clutters is from 3D raster
map (raster favorite) or 3D vector map (vector favorite). If you use 2D vector map without height
information about clutters, you shall select raster favorite.
Map data layers: the digital map used by the model. You shall import layers into Volcano model
respectively. The layers are usually consistent with the imported digital maps in U-Net.
Altimetry: raster map of terrain height. In digital maps, it is contained in the index file under the
heights or DTM directory.
Clutter: raster map of clutter type. In digital maps, it is contained in the index file under the clutter
or DLU directory.
Clutter height: raster map of clutter height. In digital maps, it is contained in the index file under
the building or DHM directory.
3D Vector: 3D vector map. In digital maps, it is contained in the index file under the vector
directory. The vector map in Volcano Macrocell model is optional. In vertical analysis mode, when
selecting vector favorite, you shall import 3D vector map, because the model requires abstracting
height information of clutters from 3D vector map.
Vector reference: it is valid only when 3D vector map is imported. It indicates whether the height
reference of vector map is ground (relative height) or sea surface (absolute height). Its reference is
usually ground.
Prediction Preferences: it is valid only when the import map contains various resolutions, such as
20 m and 5 m. It indicates the preferential resolution.
2008-12-10
Page62 , Total85
INTERNAL
12
You can configure clutter parameters in raster map in Clutter tab, as shown in 4.1.1.
Figure 1.1 Parameters in Clutters Tab for Volcano Macrocell model
When you import the raster map of clutter type (DLU), you can see various clutters in the Clutter
tab. Volcano Macrocell model describes raster maps from the following aspects:
Volcano type: the clutter type defined in Volcano. There are several clutter types. They
are Land, Water, Building, Vegetation, Bridge, Built-up area.
These six clutter types use different calculation strategies. You shall select corresponding
volcano type according to the definitions of clutter types in digital maps.
Clutter attenuation: the clutter loss. Each volcano type has default clutter attenuation,
but you can change it.
Clutter height: the clutter height. If there is no 3D map, you can specify a uniform
clutter height for each clutter type. It is invalid when you use 3D maps.
2008-12-10
Page63 , Total85
INTERNAL
13
You can configure vector parameters of vector maps in the Vectors tab, as shown in 4.1.1. If you use
2D vector map or no vector map, this tab is invalid.
Figure 1.1 Parameters in vectors tab for Volcano Macrocell model
When importing a vector map, you can see various clutter types in the Vectors tab. Volcano
Macrocell model describes vector properties from the following aspects:
Volcano type: the vector type defined in Volcano model. The Volcano types are Land,
Water, Building, Vegetation and Bridge.
These five clutter types use different calculation strategies. You shall select
corresponding volcano type according to the definitions of vector types in digital maps.
2008-12-10
Clutter attenuation: the clutter loss. Each volcano type has a default clutter loss, but
you can change it.
Page64 , Total85
INTERNAL
14
You can configure algorithm parameters in Parameter tab for Volcano Macrocell model.
Figure 1.1 Parameters in Parameter tab for Volcano Macrocell model
Free space correction: coefficient for free space correction. You can set two sets of A and B for
LOS and NLOS respectively.
Deterministic weighting: weighting factor of deterministic calculation.
Environment: environment tuning parameter. If you use low-resolution map without clutter height
layer (20-meter resolution map), you can select Low resolution; otherwise, you select Urban.
Geographic profile extraction: the algorithm to extract lateral section with Deygout method.
If you select radial, you will abstract the lateral sections between the transmitter and the
center of all rasters. For any receiver spots, select the nearest lateral section. Engineers
usually select radial.
If you select systematic, you will abstract the lateral section between the transmitter and
2008-12-10
Page65 , Total85
INTERNAL
15
You can configure model tuning parameters in Tuning tab and tune model, as shown in 4.1.1.
Figure 1.1 Parameters in Tuning tab for Volcano Macrocell model
Autotuning mode: it indicates simple tuning or full tuning. Simple tuning are for the free space
correction A and B, and deterministic weighting alpha. Full tuning is for all parameters include
clutter loss and clutter height.
Statistical tuning: It is valid when you select full tuning. It indicates whether to tune clutter loss and
clutter height. Huawei performs CW measurements in outdoor open land, so selecting No in both
2008-12-10
Page66 , Total85
INTERNAL
16
You can configure the name and description information of the model, similar to these of SPM.
Figure 1.1 Parameters in General Tab for Volcano Microcell model
17
You can configure the parameters related to map used in model and map-related aspects, as shown in
4.1.1.
2008-12-10
Page67 , Total85
INTERNAL
Figure 1.1 Parameters in Map data tab for Volcano Microcell model
Vertical analysis mode: it indicates whether the height information about clutters is from 3D raster
map (raster favorite) or 3D vector map (vector favorite). If you use 2D vector map without height
information about clutters, you shall select raster favorite.
Map data layers: the digital map used by the model. You shall import layers into Volcano model
respectively. The layers are usually consistent with the imported digital maps in U-Net.
Altimetry: raster map of terrain height. In digital maps, it is contained in the index file under the
heights or DTM directory.
Clutter: raster map of clutter type. In digital maps, it is contained in the index file under the clutter
or DLU directory.
Clutter height: raster map of clutter height. In digital maps, it is contained in the index file under
the building or DHM directory.
2DVector/3D Vector: 2D/3D vector map. In digital maps, it is contained in the index file under the
vector directory. The vector map in Volcano Microcell model is mandatory, and at least the 2D
vector map is mandatory.
Vector reference: it is valid only when 3D vector map is imported. It indicates whether the height
reference of vector map is ground (relative height) or sea surface (absolute height). Its reference is
usually ground.
Prediction Preferences: it is valid only when the import map contains various resolutions, such as
20 m and 5 m. It indicates the preferential resolution.
2008-12-10
Page68 , Total85
INTERNAL
18
You can configure clutter parameters in raster map in Clutter tab, as shown in 4.1.1.
Figure 1.1 Parameters in Clutters Tab for Volcano Microcell model
When you import the raster map of clutter type (DLU), you can see various clutters in the Clutter
tab. Volcano Microcell model describes raster maps from the following aspects:
Volcano type: the clutter type defined in Volcano. The clutter types are Land, Water,
Building, Vegetation, Bridge and Built-up area.
These six clutter types use different calculation strategies. You shall select corresponding
volcano type according to the definitions of clutter types in digital maps.
Clutter attenuation: the clutter loss. Each volcano type has a default clutter attenuation,
but you can change it.
Building Linear Loss: linear loss of buildings. You can configure it for the clutter of
building type. It is 0.5 dB/m by default. If you do not consider linear loss of buildings,
you can configure it to 0.
In Volcano Microcell model, the penetration loss of buildings includes two parts: clutter attenuation
and building linear loss, but in SPM, there is loss per clutter class only. To make Volcano model and
SPM compatible, you can configure the clutter attenuation of Volcano consistent with losses per
clutter class of SPM while you configure building linear loss to 0. In this way, SPM and Volcano
2008-12-10
Page69 , Total85
INTERNAL
19
You can configure vector parameters of vector maps in the Vectors tab, as shown in 4.1.1. If you use
2D vector map or no vector map, this tab is invalid.
Figure 1.1 Parameters in vectors tab for Volcano Microcell model
When importing a vector map, you can see various clutter types in the Vectors tab. Volcano
Macrocell model describes vector properties from the following aspects:
Volcano type: the vector type defined in Volcano model. The Volcano types are Land,
Water, Building, Vegetation and Bridge.
These five clutter types use different calculation strategies. You shall select
corresponding volcano type according to the definitions of vector types in digital maps.
2008-12-10
Clutter attenuation: the clutter loss. Each volcano type has a default clutter loss, but
you can change it.
Page70 , Total85
INTERNAL
You must configure volcano type to building in vector maps; otherwise, Volcano Microcell model will not perform multipath calculation of ray tracing.
If some 2D vector map with 5-meter resolution, the Vectors tab is invalid, gray. For the vector of
building type, you shall check whether its volcano type is Building. 4.1.1 shows the correct
configuration.
Figure 1.2 Correct configuration of vectors of building type
If the Volcano type (especially the building type) is incorrect in the Vectors tab, you need modify the
menu file for vector map by adding #BUILDING at the building type, as shown in 4.1.1. After
modification, you need re-import the vector layer.
2008-12-10
Page71 , Total85
INTERNAL
20
You can configure parameters of ray tracing algorithm for Volcano Microcell model, as shown in
4.1.1.
Figure 1.1 Parameters in Ray Tracing tab for Volcano Microcell model
Launching parameters: the parameters of ray tracing (transmission ray) algorithm used by the
model.
2008-12-10
Page72 , Total85
INTERNAL
21
You can configure other parameters for Microcell model, as show in 4.1.1.
Figure 1.1 Parameters in Parameter tab for Volcano Macrocell model
Free space correction: coefficient for free space correction. You can set two sets of A and B for
LOS and NLOS respectively.
Deterministic weighting: weighting factor of deterministic calculation.
Urban correction: environment correction factor. It includes forward correction, backward
correction, and roughness.
2008-12-10
Page73 , Total85
INTERNAL
If you select radial, you will abstract the lateral sections between the transmitter and the
center of all rasters. For any receiver spots, select the nearest lateral section. Engineers
usually select radial.
If you select systematic, you will abstract the lateral section between the transmitter and
receiver for all receivers. Therefore the calculation amount is great.
Indoor penetration: indoor prediction. The "indoor" referred herein is inside buildings of building
type.
Tune parameters: you can start model tuning by clicking Tune Parameters button.
22
You can configure the name and description information of the model, similar to these of SPM.
2008-12-10
Page74 , Total85
INTERNAL
23
You can configure the parameters related to map used in model and map-related aspects, as shown in
4.1.2.
2008-12-10
Page75 , Total85
INTERNAL
Figure 1.1 Parameters in Map data tab for Volcano Microcell model
Vertical analysis mode: it indicates whether the height information about clutters is from 3D raster
map (raster favorite) or 3D vector map (vector favorite). If you use 2D vector map without height
information about clutters, you shall select raster favorite.
Map data layers: the digital map used by the model. You shall import layers into Volcano model
respectively. The layers are usually consistent with the imported digital maps in U-Net.
Altimetry: raster map of terrain height. In digital maps, it is contained in the index file under the
heights or DTM directory.
Clutter: raster map of clutter type. In digital maps, it is contained in the index file under the clutter
or DLU directory.
Clutter height: raster map of clutter height. In digital maps, it is contained in the index file under
the building or DHM directory.
2DVector/3D Vector: 2D/3D vector map. In digital maps, it is contained in the index file under the
vector directory. The vector map in Volcano Microcell model is mandatory, and at least the 2D
vector map is mandatory.
Vector reference: it is valid only when 3D vector map is imported. It indicates whether the height
reference of vector map is ground (relative height) or sea surface (absolute height). Its reference is
usually ground.
Prediction Preferences: it is valid only when the import map contains various resolutions, such as
20 m and 5 m. It indicates the preferential resolution.
2008-12-10
Page76 , Total85
INTERNAL
24
You can configure clutter parameters in raster map in Clutter tab, as shown in 4.1.2.
Figure 1.1 Parameters in Clutters Tab for Volcano Minicell model
When you import the raster map of clutter type (DLU), you can see various clutters in the Clutter
tab. Volcano Minicell model describes raster maps from the following aspects:
Volcano type: the clutter type defined in Volcano. The clutter types are Land, Water,
Building, Vegetation, Bridge and Built-up area.
These six clutter types use different calculation strategies. You shall select corresponding
volcano type according to the definitions of clutter types in digital maps.
Clutter attenuation: the clutter loss. Each volcano type has a default clutter attenuation,
but you can change it.
Building Linear Loss: linear loss of buildings. You can configure it for the clutter of
building type. It is 0.5 dB/m by default. If you do not consider linear loss of buildings,
you can configure it to 0.
In Volcano Minicell model, the penetration loss of buildings includes two parts: clutter attenuation
and building linear loss, but in SPM, there is loss per clutter class only. To make Volcano model and
SPM compatible, you can configure the clutter attenuation of Volcano consistent with losses per
clutter class of SPM while you configure building linear loss to 0. In this way, SPM and Volcano
model have same indoor penetration loss.
2008-12-10
Page77 , Total85
INTERNAL
25
You can configure vector parameters of vector maps in the Vectors tab, as shown in 4.1.2. If you use
2D vector map or no vector map, this tab is invalid.
Figure 1.1 Parameters in vectors tab for Volcano Minicell model
When importing a vector map, you can see various clutter types in the Vectors tab. Volcano
Macrocell model describes vector properties from the following aspects:
Volcano type: the vector type defined in Volcano model. The Volcano types are Land,
Water, Building, Vegetation and Bridge.
These five clutter types use different calculation strategies. You shall select
corresponding volcano type according to the definitions of vector types in digital maps.
Clutter attenuation: the clutter loss. Each volcano type has a default clutter loss, but
you can change it.
Building Linear Loss: linear loss of buildings You can configure it for the clutter of
building type. It is 0.5 dB/m by default. If you do not consider linear loss of buildings,
you can configure it to 0.
2008-12-10
Page78 , Total85
INTERNAL
You must configure volcano type to building in vector maps; otherwise, Volcano Microcell model will not perform multipath calculation of ray tracing.
If some 2D vector map with 5-meter resolution, the Vectors tab is invalid, gray. For the vector of
building type, you shall check whether its volcano type is Building. 4.1.2 shows the correct
configuration.
Figure 1.2 Correct configuration of vectors of building type
If the Volcano type (especially the building type) is incorrect in the Vectors tab, you need modify the
menu file for vector map by adding #BUILDING at the building type, as shown in 4.1.2. After
modification, you need re-import the vector layer.
2008-12-10
Page79 , Total85
INTERNAL
26
You can configure parameters of ray tracing algorithm for Volcano Minicell model, as shown in
4.1.2.
Figure 1.1 Parameters in Ray Tracing tab for Volcano Minicell model
Launching parameters: the parameters of ray tracing (transmission ray) algorithm used by the
Minicell model.
2008-12-10
Page80 , Total85
INTERNAL
27
You can configure other parameters for Minicell model, as show in 4.1.2.
Figure 1.1 Parameters in Parameter tab for Volcano Minicell model
Free space correction: coefficient for free space correction. You can set two sets of A and B for near
region and far region respectively.
Deterministic weighting: weighting factor of deterministic calculation.
Ray-Tracing Weighting: weighting factor of ray tracing calculation. It includes reflection weight,
diffraction weight, and backward weight.
2008-12-10
Page81 , Total85
INTERNAL
28
29
30
31
32
Import map.
----End
The detailed steps are skipped herein, which are in the sections 3.2and 3.2.3. This section describes
the process of model tuning and the method to check tuning result.
2008-12-10
Page82 , Total85
INTERNAL
33
After filtering data and setting model correctly, you can tune Volcano models.
In the propagation model properties dialog box, click Tuning Parameters button, and a Volcano
Tuning dialog box is displayed. The Volcano Macro/Micro/Mini model tuning dialog boxes are
similar, as shown in 4.2.1.
Figure 1.1 Volcano tuning dialog box
The only difference between micro model and other two models is the Autotuning mode drop-down
list, which includes full tuning and Simple tuning.
2008-12-10
Page83 , Total85
INTERNAL
Figure 1.2 Selecting automatic tuning mode for Volcano Microcell model
The automatic tuning mode of Volcano Macrocell model is selected in the Parameters tab. For
Macrocell/Microcell model, the full tuning mode is recommended. Full tuning and simple tuning
make no difference for Minicell model.
34
As shown in 4.2.1, you can see the imported CW measurement data in the upper part of the dialog
box. You can select one or more groups of data as required. After selection, start automatic tuning by
clicking the Start button. The tuning time depends on the type of Volcano model
(Macro/Micro/Mini) and amount of data. Generally, tuning Macrocell model takes least time, usually
within half a minute. Tuning Microcell/Minicell is slower, about 4-10 minutes.
The Tuning Report dialog box displays the tuned parameters. The most important parameters are A
2008-12-10
Page84 , Total85
INTERNAL
and B. The range of tuned A is [5, 5] while that of tuned B is [20, 30].
Apply the tuned parameters to the model by clicking Apply button. You can see open a detailed
tuning report by clicking Show results, and the report is a text file.
Figure 1.2 Calibration result
Standard deviation
Correlation factor
Clutter result
CW measurement proceeds in open land, so there must be an error due to location error if a point is
on other clutters. If these points have great impact on result, you shall re-tune after deleting these
points.
The displayed diagram of tuning result and steps to verify result are similar to these of SPM. You can
refer to 3.2.6.
2008-12-10
Page85 , Total85