Professional Documents
Culture Documents
Tems Investigation PDF
Tems Investigation PDF
In general, Drive Test can be define as a methode that used to verify the actual condition of RF signal
certain operator at certain place.
Several functions of drive test :
- Analyzing customer complaint of certain operator in their home or office area
- Finding problem in BTS ( Timeslot Check, TRX Check, Swap Feeder)
- Analyzing the result of optimization process (continuity and all of area)
There are softwares can be used for drivetest that installed on laptop. TEMS Investigation (Ericsson),
NEMO (Nokia).
Here the steps to start learning drivetest with TEMS Investigation :
a. Drive Test Equipment
1. TEMS Handset (complete with Charger, Headset, Data Cable) and USB Hub
5. Scanner for WCDMA (Ext Antenna GPS and RF, Data Cable)
B. Laptop Configuration
1. Power Management
Set Power Management Laptop always On :
Start -> Settings -> Control Panel -> Power Options -> Set All Power Scheme never
2. Virtual Memory
Set Virtual Memory :
Start -> Settings -> Control Panel -> System
Advance -> Performance Settings
C. TEMS Investigation :
- Workspace Configuration
After installition process, open Tems Investigation.
>> All Programs -> TEMS Investigation -> Data Collect
This is the example workspace for 2G (Mode Dedicated-Idle).
- Map Configurations
Create Geoset : Click Geoset Manager on Map window
1. On layer control
remove all layer except Pinpoint, Cell, Event, AMR, RF Quality and Coverage
layer
2. Add layer Route, Road, MCOM Site, and other *.tab
3. Save Geoset
4. Load Cell file : Configuration -> General -> Cellfile Load
5. Use Cell Definition File then choose cell file
4.
5.
6.
7.
Video Call CS
In general cs for video call is same as voice call, but in video call in dial command we must add v.
i.e
Loop Start
Dial v081384760975
Wait 120
End Call
Wait 15
Loop End
D. DRIVE TEST
1. Configure Recording Properties : Menu Tab Logfile -> Recording Properties
2. Select recording folder : Click Browse -> Select Directory
3. Select Quick logging and setup size of swap file after reaching message
4. Use 2G or 3G configured workspace (with spacific map : road, route, cell file)
5. Make sure all equipments configured to the right port
6. Connect all
7. After all equipments connected (symbol green), window gps, serving neighbour gsm, current
channel and events will be full filled
8. Dont forget to lock TEMS Handset into GSM only or 3G only.
10. After all route complete, wait untill call end then stop command sequence and stop recording.
F. POST PROCESSING:
- Report Generator
1. Open TEMS Data Collection : Start -> TEMS Products -> TEMS Investigations6.1.4 Data Collection
2. Menu Tab Logfile -> Report Generator
3. Add logfile
- Cell Id
- Frequncy Band
- Latitude
- Longitude
for WCDMA Dedicated / Idle / Scanner :
- AS Cell Name
- AS CPICH Ec/No
- AS CPICH RSCP
- SAN CPICH Ec/No
- SAN CPICH RSCP
- SAN Cell Id (CI Part)
- Sc 1st Aggr Ec (dBm) -> Scanner
- Sc 1st Aggr EcIo (dB) -> Scanner
- Sc Best SC -> Scanner
- Latitude
- Longitude
5. Configure Options Tab
6. Save *.mex
7. Choose Logfile : Click Browse file
8. If there are more than one logfile we can merge it by Merge Output
9. Choose Output directory : Click Browse dir
10. Give Prefix : Ded if Dedicated and Idle if Idle
14. Open the exported file into MapInfo : Menu Tab File -> Open
15. Create Thematic Map : Menu Tab Map -> Create Thematic Map
16. Choose Type -> Range
17. Template Name -> Region Ranges
18. Choose Table and Field (ie. Plotting RXQUAL_SUB from Dedicated mode)
EVENTS on RXQUAL_SUB
21. Create Events on RXQUAL_SUB
22. Open again the exported file (Ded_orinaica)
23. Create Thematic Map : Menu Tab Map -> Create Thematic Map
24. Choose Type -> Individual
SPIDER GRAPH
29. Activate spider graph : Menu Tab Tools -> Tool Manager
30. Spider Graph Load and Autoload
31. See table structure of cell in MCOM Site : Menu Tab Table -> Maintenance -> Table Structure ->
View/Modify Table choose MCOM Site
32. See table structure of CI in exported file : Manu Tab Table -> Maintenance -> Table Structure ->
View/Modify Table choose exported file (ie. Ded_orinaica) -> Change type structure of CI
33. Click OK
34. Create Spider Graph : Tools -> Spider Graph -> Spider Graph
35. Choose Origin and Destination table
36. Save the Spider Graph table : Save Copy As -> (ie. orinaica)
37. From Spider Graph, We can analyze :
- Dominant Cells
- Overshoot Cells
- Swap Feeder
G. TROUBLESHOOTING :
- 2G Frequency Scanning
Purpose : to verify level signal each BCCH ARFCN plan
1. Setup frequency scan : Click Scan Properties
2. Select channels : Tab Scanned channels -> Manual selection -> Select
3. Setup Selected Channels (ie. BCCH ARFCN are 95-113)
4. Decode BSIC
- TRX Check
Purpose : to verify damage TRX in each sector
Where is TRX ?
2. Set HO Target : Equipment Properties -> Dedicated Mode -> Function -> Target HO (ie. BCCH 547,
540, 543)