Professional Documents
Culture Documents
Metal Deck CALCULATION
Metal Deck CALCULATION
FULL OUTPUT
SECTION PROPERTIES :
***NOTE - 1: All values of inertia are expressed in steel units
***NOTE - 2: Average inertia is used for deflection calculations for the composite stage
***NOTE - 3: Cracked dynamic inertia is used for natural frequency calculations
DECK PROFILE:
Sagging Inertia, Ixx 41.500 cm4/m Area of profile (Net), Ap 1137 mm/m
Hogging Inertia, Iyy 0.000 cm4/m
COMPOSITE:
Inertia, Ixx - Uncracked 2666 cm4/m Cracked 1348 cm4/m
Average inertia 2007 cm4/m Cracked inertia (dynamic) 1534 cm4/m
Shear bond coefficients - Mr 86.80 Kr 0.039600
Concrete volume 0.131 m/m/m
FIRE DATA :
Design method FIRE ENGINEERING Fire resistance period 60 mins
Non-permanent imposed loads 0.0 kN/m
CONSTRUCTION STAGE
SAGGING:
Max applied moment = [0.080 * 0.13 + 0.094 * 4.31 + 0.094 * 0.11 + 0.094 * 3.43] * 1.95^2
= 2.83 kNm/m
Moment resistance, Mc = 4.63 kNm/m
UNITY FACTOR = 0.61 PASS
HOGGING:
Max. applied moment = 2.16 kNm/m
Moment resistance, Mc = 4.67 kNm/m
UNITY FACTOR = 0.46 PASS
DEFLECTION CHECK :
Allowable deflection max, is the lesser of
1) Effective span/180 (= 10.8 mm ), and
2) 20 mm ( absolute maximum value ), and
3) Slab depth/10 = ( 15.0 mm )
Max. self weight deflection = 3.78 mm
( < 10.81 mm ) SATISFACTORY
***NOTE: Deflection within code limits; ponding is not considered
NORMAL STAGE
EFFECTIVE SPAN :
Effective span Le, is the smaller of
1) c/c of supports
2) clear span + slab overall depth - depth to centroid = 1.9 + 150 / 1000 - 20.38 / 1000
= 2.03 m
Therefore Le = 2.03 m
DEFLECTION CHECK :
Allowable deflection max-i under imposed loads, is the lesser of
1) Effective span/350 (= 5.8 mm ), and
2) Absolute maximum value (mm) = 20
Imposed load deflection = 0.013 * 9.50 * (2.03* 1000 )^4 / (205*20069910 )/1000
= 0.3 mm ( < 5.8 mm ) SATISFACTORY
Allowable total deflection max-t, is the lesser of
1) Effective span/250 or 8.1 mm, and
2) 30 mm ( SCI recommended absolute maximum value )
Deflection due to imposed loads = 0.3 mm (based on average inertia)
Additional deflection due to superimposed dead loads = 0.4 mm (based on average inertia)
Total deflection = 0.3 + 0.4
= 0.7 mm ( < 8.1 mm ) SATISFACTORY
DYNAMIC SENSITIVITY :
*** NOTE: loads are dead + super-imposed dead + 10% imposed
Dynamic inertia (cracked section) = 1534 cm4
Maximum deflection = 0.013 * 11.11 * (2.03* 1000 )^4 / (205*15335150 )/1000
= 0.79 mm
Frequency = 18 / 0.79 )
= 20.30 Hz ( > 5.00 Hz) SATISFACTORY