Professional Documents
Culture Documents
Common-Base Configuration (CB) - GDLC
Common-Base Configuration (CB) - GDLC
The CB configuration having a low input and high output impedance and a current gain less
than 1, the voltage gain can be quite large, ro in M so that ignored in parallel with RC
[6-54]
Zo
[6-55]
Av
[6-56]
Ai Assuming RE >> re
[6-57]
Phase Relationship: the resulting equation for the Av is a positive reveals that the output Vo
and input Vi are in phase for the common-base configuration
Fig6-24 Ex 8
Solution:
IE
114
re
Zi
Zo
Av
Ai
115
[6-58]
Zo to define Zo set Vi to zero , the effect of re is removed and RF appears in parallel with RC
[6-59]
[6-60]
116
Ignoring re compared to RF and RC gives us
[6-61]
RC >> RF
[6-62]
Phase Relationship: the negative sign in the resulting equation for the Av reveals that a 180
phase shift occurs between the output VO and input Vi
Fig6-27 Example 9:
Solution:
IB
IE
re
Zi
Zo
Av
Ai
117
For the configuration of Fig6-28, will determine the variables
[6-63]
Zo
[6-64]
Av
[6-65]
Ai
[6-66]
[6-67]
Zo
[6-68]
For ro 10RC
118
[6-69]
Av
[6-70]
For ro 10RC
[6-71]
Ai for the input side
[6-72]
[6-73]
Or [6-74]
Phase Relationship: the negative sign in the resulting equation for the Av reveals that a 180
phase shift occurs between the output VO and input Vi
119
Example 10: For the network of fig6-31 determine:
Fig6-31 Example 10
Solution: DC testing:
IB
IE
re
re
Zi
F ig6-32 re equivalent
It is satisfied
So Zo
120
Approximate Hybrid Equivalent Circuit
hie = re
hfe =
hoe= 1/ro
hfb= -
hib =re
Zi
[6-75]
Zo
[6-76]
Av
[6-77]
Ai Assuming that RB >> hie and 1/ hoe 10RC, then Ib Ii and IO = IC = hfe Ib = hfe Ii with
[6-78]
Fig6-38Voltage-dividerbiasconfiguration
Zi RB=R'
[6-79]
Zo
[6-80]
Av
[6-81]
Ai
[6-82]
122
Fig6-39 CE unbypassed emitter-bias configuration
Zi:
[6-83]
[6-84]
Zo
[6-89]
Av
And [6-90]
Ai
[6-91]
or [6-92]
Fig6-40Emitter-follower configuration
Zi
[6-93]
123
[6-94]
[6-95]
Av
[6-96]
Ai
[6-97]
or [6-98 ]
Fig6-41 CB configuration
Zi
[6-99]
Zo
[6-100]
124
Av
[6-101]
Ai
[6-102]
125
Table6-1 Relative Levels for the Important Parameters of the CE, CB, and CC Transistor
Amplifier
126
SUMMARY
Important Conclusions and Concepts
1. The re model for a BJT in the ac domain is sensitive to the actual dc operating conditions of
the network. This parameter is normally not provided on a specification sheet, although hie of
the normally provided hybrid parameters is equal to re but only under specific operating
conditions.
2. Most specification sheets for BJT include a list of hybrid parameters to establish an ac
model for the transistor. One must be aware, however, that they are provided for a particular
set of dc operating conditions.
3. The CE fixed-bias configuration can have a significant voltage gain characteristic, although
its input impedance can be relatively low. The approximate current gain is given by simply
beta, and the output impedance is normally assumed to be Rc.
4. The voltage-divider bias configuration has a higher stability than the fixed-bias configuration,
but it has about the same voltage gain, current gain, and output impedance. Due to the biasing
resistors, its input impedance may be lower than that of the fixed-bias configuration.
5. The CE emitter-bias configuration with an unbypassed emitter resistor has a larger input
resistance than the bypassed configuration, but it will have a much smaller voltage gain than
the bypassed configuration. For the unbypassed or by-passed situation, the output impedance
is normally assumed to be simply Rc.
6. The emitter-follower configuration will always have an output voltage slightly less than the
input signal. However, the input impedance can be very large, making it very useful for
situations where a high-input first stage is needed to "pick up "as much of the applied signal as
possible. Its output impedance is extremely low, making it an excellent signal source for the
second stage of a multistage amplifier.
7. The common-base configuration has very low input impedance, but it can have a significant
voltage gain. The current gain is just less than 1, and the output impedance is simply Rc
8. The collector feedback configuration has input impedance that is sensitive to beta and that
can be quite low depending on the parameters of the configuration. However, the voltage gain
can be significant and the current gain of some magnitude if the parameters are chosen
properly. The output impedance is most often simply the collector resistance Rc
9. The collector dc feedback configuration utilizes the dc feedback to increase its stability and
the changing state of a capacitor from dc to ac to establish a higher voltage gain than obtained
with a straight feedback connection. The output impedance is usually close to Rc and the input
impedance relatively close to that obtained with the basic common-emitter configuration.
10. The approximate hybrid equivalent network is very similar in composition to that used with
the re model. In fact, the same methods of analysis can be applied to both models. For the
hybrid model the results will be in terms of the network parameters and the hybrid parameters,
whereas for the re model they will be in terms of the network parameters and , re and ro
127
12. for BJT amplifiers that fail to operate properly, the first step should to be checking the dc
level and be sure that they support the dc operation of the design.
13. Always keep in mind that capacitors are typically open circuits for the dc analysis and
operation and essentially short circuits for the ac response
Equations
CE fixed bias:
CE Voltage-divider bias:
CE emitter-bias:
Emitter-follower:
Common-base:
128
Collector feedback:
Collector dc feedback:
129
7-Felid Effect Transistor (FET)
BJT is a current-controlled device; that is IB controls IC. The FET is a voltage-controlled device
in which the voltage gate VG controls current through the device. FET is a three-terminal device
containing one p-n junction built as either a Junction FET (JFET) or a Metal-Oxide
Semiconductor FET (MOS-FET).
Construction and Characteristics of JFETS
JFET is a type of FET that operates with a reverse biased junction to control current in the
channel. JFETs either n channel or p channel
JFET Characteristics
First consider the case where the VGS = 0V fig7-4a as VDD (and thus VDS) is increased from
0V, ID will increase proportionally (Fig7-4b between points A and B), this region is called the
ohmic region because VDS and ID are related by Ohm's law.
Point B in Fig7-4b ID becomes constant. As VDS increases from point B to point C, the reverse-
bias voltage in VGD produces a depletion region large enough to offset the increase in VDS, thus
keeping ID relatively constant.
Pinch-Off Voltage VP: is the value of VDS at which ID becomes constant and VGS = 0V, a
continued increase in VDS above the VP voltage produces a constant drain current IDSS (Drain
to Source current with gate sorted)
IDSS: is the maximum drain current and is always specified on JFET data sheets, is defined by
the condition VGS = 0V and VDS > |VP |
Breakdown: occurs at point C when ID begins to increase very rapidly with any further
increase in VDS , Breakdown result damage to the device, so JFETs are always operated
below breakdown ( between B & C).
VGS Controls ID: Connect a bias voltage VGG, as VGS is set to increasingly more negative
values by adjusting VGG, ID decreases.
130
Fig 7-4 the drain characteristic curve of a JFET for VGS = 0 V, (pinch-off)
Fig7-5 pinch-off occurs at a lower VDS as VGS is increased to more negative values
Cutoff Voltage VGS(off) : the value of VGS that makes ID approximately zero ,JFET must be
operated between VGS = 0V and VGS(off) , for this range of voltage ID will vary from a maximum (
IDSS ) to a minimum . VGS(off) & VP are always equal in magnitude but opposite in sign
(a) VGS = 0V, ID = IDSS (b) cutoff (ID = 0A) VGS less than (more negative) VP
(c) ID exists between 0A and IDSS for VGS less than or equal to 0V and greater than the VP
Fig7-6
131
The basic operation of a p-channel JFET is the same as for an n-channel device expect that is
requires a negative VDD and a positive VGS.
Example 1: JFET in fig VGS(off) = -3.5V & IDSS =6mA. Determine the minimum value of VDD
required putting the device in the constant-current region of operation
Solution:
Example2: A certain JFET has an IGSS of 1nA for VGS = -20V, Determine the input resistance
Solution:
Voltage-Controlled Resistor
In ohmic region JFET be employed as a variable resistor whose resistance is controlled by VGS
[7-1]
ro is the resistance with VGS = 0V, and rd the resistance at a particular level of VGS
132
This liner relationship dose not exists between the output and input quantities of the JFET, the
relationship between ID and VGS is defined by Shockley's equation:
[7-3]
The transfer characteristics defined by Shockley's equation are unaffected by the network in
which the device is employed
[7-4]
[7-5]
if we substitute VGS = -1V.
[7-6]
Test Eq[7-6]by finding VGS that will result in a drain current of 4.5mA in fig7-8
133
Shorthand Method
We can have a shorthand method as following: if we specify VGS to be 1/2 VP the resulting level
of ID will be the following, as determine by Shockley's equation
And [7-7]
ID for VGS =VP/2 = -4V/2 = -2V, if we choose ID = IDSS /2 & substitute into Eq[7-6]
[7-8]
Example 3: Sketch the transfer curve defined by IDSS = 12mA and VP = -6V
Solution:
Fig7-10 D-MOSFETs
The D-MOSFET called a depletion/enhancement MOSFET, D-MOSFET operates in the
Depletion mode when a VGS is negative, Enhancement mode when VGS is a positive voltage.
Depletion Mode
Visualize the gate as one plate of a parallel plate capacitor and the channel as the other plate.
The SiO2 insulating layer is the dielectric. With VGS negative voltage, the negative charges on
the gate repel conduction electrons from the channel, leaving positive ions in their place. Thus
decreasing the channel conductivity, The greater the negative voltage (VGS ), the greater the
depletion of n-channel electrons, at a VGS(off) the channel is totally depleted and ID is zero. In
depletion mode current between drain and source will result from a voltage connected across
the drain-source.
(a)Depletion mode VGS negative < VGS(off) (b) Enhancement: VGS positive
Fig7-11n-channel DMOSFET
135
Like the n-channel JFET, the n-channel D-MOSFET conducts ID for VGS between VGS(off) and
0V. The D-MOSFET conducts for values of VGS above 0 V.
136
ID increases very rapidly with increasing positive values of VGS. So that choice values to be
substituted into Shockley's equation. In this case, we will try +1V as follows:
For n-channel device, a positive VGS voltage above VGS(off) (threshold voltage)creating a thin
layer of negative charges in the substrate region adjacent to the SiO2 layer, the conductivity of
the channel is enhanced by increasing the VGS voltage, thus pulling more electrons into the
channel. For any VGS voltage below the threshold value, there is no channel.
[7-11]
[7-12]
For values of VGS less than the threshold level, ID = 0mA
[7-13]
137
Fig7-16 n-EMOSFET VT=2V&k=0.278x10-3 A/V2
[7-14]
And a point on the plot is obtained as in fig7-18b, finally, additional levels of VGS are chosen
and the resulting levels of ID obtained. In particular, at VGS =6, 7, and 8V, the level of ID is 2,
4.5, and 8mA, respectively, as shown on the resulting plot of fig7-18
138
Fig7-18 Transfer char of n-EMOSFET with VT = 4V & k = 0.5 x 10-3 A/V2
For VGS =8, 10, 12,14V, ID will be 1.525, 3, 4.94, 7.38mA respectively.
Solution to Example 4:
139
CMOS
CMOS is a complementary MOSFET constructed by a p-channel and an n-channel MOSFET
on the same substrate. P-channel on the left and the n-channel on the right
140
SUMMARY
1. a current controlled device is one in which a current defines the operating condition of the
device, whereas a voltage-controlled device is one in which a particular voltage defines the
operating conditions.
2. Transistors are used as either amplifying devices or switching devices.
3. A field-effect transistor (FET) has three terminals: source, drain, and gate.
4. A junction field-effect transistor (JFET) operates with a reverse-biased gate-to-source pn
junction. JFETs have very high input resistance due to the reverse-biased gate-source
junction.
5. JFET current between the drain and the source is through a channel whose width is
controlled by the amount of reverse bias on the gate-source junction.
6. The two types of JFETs are n-channel and p-channel.
7. The JFET can actually be used as a voltage-controlled resistor because of a unique
sensitivity of the drain-to-source impedance to the gate-to-source voltage.
8. The maximum current for any JFET is labeled IDSS and occurs when VGS =0V.
9. The maximum current for a JFET occurs at pinch-off defined by VGS = VP .
10. The relationship between the drain current and the gate-to-source voltage of a JFET is
nonlinear one defined by Shockley's equation. As the current level approaches IDSS, the
sensitivity of ID to changes in VGS increases significantly
11. The transfer characteristics (ID versus VGS) are characteristics of the device itself and not
sensitive to the network in which the JFET is employed.
12. When VGS = VP/2, ID = IDSS /4; and at a point where ID = IDSS /2, VGS =0.3 V.
13. Maximum operating conditions are determined by the product of the drain-to-source
voltage and the drain current.
14. Metal-oxide semiconductor field-effect transistors (MOSFETs) differ from JFETs in that the
gate of a MOSFET is insulated from the channel.
15. MOSFET is available in one of two types: depletion and enhancement.
141
16. The depletion-type MOSFET has the same transfer characteristics as a JFET for drain
current up to the IDSS level. At this point the characteristics of a depletion-type MOSFET
continue to levels above IDSS, whereas those of the JFET will end
17. A depletion/enhancement MOSFET (D-MOSFET) can operate with a positive, negative. Or
Zero gate-to-source voltage.
18. The D-MOSFET has a physical channel between the drain and the source.
19. The arrow in the symbol of n-channel JFET or MOSFET will always point in to the center of
the symbol, whereas those of a p-channel device will always point out of the center of the
symbol.
20. An enhancement-only MOSFET (E-MOSFET) can operate only when the gate-to-source
voltage exceeds a threshold value.
21. The E-MOSFET has no physical channel.
22. The transfer characteristics of an enhancement-type MOSFET are not defined by
Shockley's equation but rather by a nonlinear equation controlled by the gate-to-source
voltage, the threshold voltage, and a constant k defined by the device employed. The resulting
plot of ID versus VGS is one that rises exponentially with increasing values of VGS.
23. A CMOS (complementary MOSFET) device is one that employs a unique combination of a
p-channel and an n-channel MOSFET with a single set of external leads. It has the advantages
of very high input impedance, fast switching speeds, and low operating power levels, all of
which make it very useful in logic circuits.
EQUATIONS:FET
MOSFET (enhancement):
142