Professional Documents
Culture Documents
Eastern Visayas State University: Set D
Eastern Visayas State University: Set D
College of Engineering
Civil Engineering Department
a 273.7 kN b 1516.84 kN
c 90.32 kN d 1140.48 kN
10 . (b) Based on the bearing capacity of bolts.
a 764.12 kN b 1348.3 kN
c 1013.76 kN d 1140.48 kN
11 . (c) Based on block shear stress.
a 446.22 kN b 787.36 kN
c 666 kN d 592 kN
12 . A square hollow steel strut shown in Figure STLD 1802 with a
wall thickness, t1 = 12 mm is pin connected to two gusset
plates, having a thickness t2 = 12 mm, which are welded to the
base plate having a thickness of 12 mm and fastened to a
concrete base by 4 - 16 mm diameter anchor bolts. Diameter of
pin is 16 mm. Compressive load P = 48 kN, θ = 30°.(a) Calculate
the bearing stress between the strut and the pin.
a 331650 N. b 495000 N.
c 396000 N. d 661320 N.
21 . Determine the tensile capacity of the lapped joint based on
block shear strength.
a 361867 N. b 557700 N.
c 540100 N. d 931359 N.
22 . A wood-stave penstock of 1.8-m diameter is wrapped with steel
hoops and subjected to a fluid pressure of 380 kPa. If the
allowable tension in the hoops is 44.2 kN, what is the maximum
hoop spacing in millimeters?
a 86.59 mm. b 129.24 mm.
c 123.98 mm. d 207.04 mm.
23 . The shaft shown in Figure SMAT 1812 is made of bronze and steel
and is fixed at both ends. It is subjected to a concentrated
torque, 8 kN-m, applied at the junction. The steel segment is
1.5 meters long and the bronze segment is 1.2 meters. For
BRONZE: d = 75 mm. ; G = 35 GPa. For STEEL: d = 50 mm. ; G = 83
GPa. (a) Determine the maximum shearing stress in the Steel
section.
a 0.4946 b 0.5138
c 0.1696 d 0.826
46 . (b)What is the maximum Ratio of actual to allowable bending
stress for combination of 0.75(D+L+W) load?
a 0.4325 b 0.4181
c 0.1427 d 0.6983
47 . (c) What is the maximum Ratio of actual to allowable bending
stress for combination of (D+L) load if one line of sag rod was
placed at mid-span?
a 0.4074 b 0.5853
c 0.608 d 0.9774
48 . A restrained beams with a span of 4 meters has a rectangular
cross-section (150 mm. × 300 mm.). The unit weight of the
material used is 500 N per cubic meters. The beam is to carry a
superimposed uniformly distributed load of 20 N/m. What is the
maximum bending stress of on the Beam?
a 0.0154 MPa. b 0.023 MPa.
c 0.0076 MPa. d 0.0331 MPa.
49 . A restrained beams with a span of 4 meters has a rectangular
cross-section (150 mm. × 300 mm.). The unit weight of the
material used is 500 N per cubic meters. The beam is to carry a
superimposed uniformly-varrying distributed load of 20 N/m from
one support an 5 N/m at the other. (a)What is the maximum
bending stress of on the Beam?
a 0.013 MPa. b 0.0372 MPa.
c 0.0279 MPa. d 0.0194 MPa.
50 . (b) What is the moment of inertia with respect to the major
axis, Ix?
a 226125000 mm4. b 112218750 mm4.
c 84375000 mm4. d 337500000 mm4.