Professional Documents
Culture Documents
Issue 01
Date 2017-03-20
and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd.
All other trademarks and trade names mentioned in this document are the property of their respective
holders.
Notice
The purchased products, services and features are stipulated by the contract made between Huawei and the
customer. All or part of the products, services and features described in this document may not be within the
purchase scope or the usage scope. Unless otherwise specified in the contract, all statements, information,
and recommendations in this document are provided "AS IS" without warranties, guarantees or
representations of any kind, either express or implied.
The information in this document is subject to change without notice. Every effort has been made in the
preparation of this document to ensure accuracy of the contents, but all statements, information, and
recommendations in this document do not constitute a warranty of any kind, express or implied.
Website: http://www.huawei.com
Email: support@huawei.com
Contents
1 Introduction.................................................................................................................................... 1
1.1 Scope.............................................................................................................................................................................. 1
1.2 Intended Audience.......................................................................................................................................................... 2
1.3 Change History............................................................................................................................................................... 2
1.4 Differences Between Base Station Types....................................................................................................................... 2
7 Parameters..................................................................................................................................... 47
8 Counters........................................................................................................................................ 92
9 Glossary....................................................................................................................................... 174
10 Reference Documents............................................................................................................. 175
1 Introduction
1.1 Scope
This document describes ATM Transport, including its technical principles and engineering
guidelines.
This document covers the following features:
l WRFD-050301 ATM Transmission Introduction Package
l WRFD-05030101 ATM over E1T1 on Iub Interface
l WRFD-05030102 ATM over Channelized STM-1/OC-3 on Iub Interface
l WRFD-05030103 ATM over Non-channelized STM-1/OC-3c on Iub/Iu/Iur Interface
l WRFD-05030104 Dynamic AAL2 Connections in Iub/IuCS/Iur Interface
l WRFD-05030105 Permanent AAL5 Connections for Control Plane Traffic
l WRFD-05030106 Call Admission Based on Used AAL2 Path Bandwidth
l WRFD-05030107 CBR, rt-VBR, nrt-VBR, UBR ATM QoS Classes
l WRFD-05030110 F5
l WRFD-050304 IMA Transmission for E1T1 or Channelized STM-1/OC-3 on Iub
Interface
l WRFD-050305 UBR+ATM QoS Class
This document applies to the following NE types.
NE Type NE Model
l Feature change
Changes in features of a specific product version
l Editorial change
Changes in wording or addition of information and any related parameters affected by
editorial changes
RAN19.1 01 (2017-03-20)
This issue does not include any changes.
Huawei radio access network (RAN) provides ATM-based Iub/Iu-CS/Iu-PS/Iur interfaces and
ATM TRM, such as admission control based on AAL2 path bandwidth, transmission resource
mapping based on ATM QoS classes, and Iub overbooking.
NOTE
3 Protocol Stacks
The transport network layer of the Iub interface consists of the transport network layer control
plane (area A), transport network layer control plane (area B), and transport network layer
user plane (area C).
l Areas A, B, and C share the physical layer and ATM layer. Therefore, all links in the
three areas can be carried on common physical links.
l Links in areas A and B are carried on SAAL links. Based on the type of carried
information, the upper layer of area A is classified into the NodeB Control Port (NCP)
and the Communication Control Port (CCP). Only Q.AAL2 links are carried in area B.
l In area C, the user plane data is carried on AAL2 paths. The bearer at the lower layer is
the ATM PVC. Under the control of Q.AAL2, AAL2 connections can be dynamically set
up or released for upper-layer services. Therefore, each AAL2 path must have its
corresponding controlling Q.AAL2.
l For the BSC6900, the signaling processing subsystem consists of SPU boards, and the
service processing subsystem consists of DPU boards. For the BSC6910, the signaling
processing subsystem and service processing subsystem consist of GPU boards.
l The RINT shown in Figure 3-2 refers to Iub ATM interface boards, including UOIa/
UOIc/AOUa/AOUc/AEUa for the BSC6900 and UOIc/AOUc for the BSC6910.
NOTE
The RINT shown in Figure 3-3 refers to Iub interface boards, including UOIa/UOIc/AOUa/AOUc/
AEUa for the BSC6900 and UOIc/AOUc for the BSC6910.
Network Segments
Iub OM channel travels through the following network segments before reaching the NodeB:
l The 80.168.3.0 segment (with network mask of 255.0.0.0) between the O&M board and
the ATM interface board. This network segment is set before delivery of the RNC.
NOTE
When the preconfigured network segment conflicts with an external IP network segment, you can
run the SET SUBNET command to set the internal subnet number.
l The 12.13.1.0 segment (with network mask of 255.255.255.0) between the ATM
interface board and the NodeBs. Set this network segment as required.
The transport network layer of the Iu-CS interface consists of the following areas:
l Transport network layer control plane (area A)
l Transport network layer control plane (area B)
l Transport network layer user plane (area C)
Areas A, B, and C share the physical layer and ATM layer. Therefore, all links in the three
areas can be carried on common physical links.
The MSC in an R99 network implements the functions in areas A, B, and C of the protocol
stack. The MSC server and MGW in an R4/R5/R6/R7/R8 network implement their functions
as follows:
l The MSC server implements the functions in area A.
l The MGW implements the functions in areas B and C.
The network may require multiple MGWs depending on the traffic volume.
In practice, data from the MSC server is not directly sent to the RNC, but forwarded to the
RNC through the route on the MGW. Figure 3-7 shows an example of Iu-CS networking in
the 3GPP R4/R5/R6/R7/R8.
Table 3-1 Differences between signaling point configuration in R99 and that in
R4/R5/R6/R7/R8
Item R4/R5/R6/R7/R8 R99
The transport network layer of the Iu-PS interface consists of the transport network layer
control plane (area A) and the transport network layer user plane (area C).
Areas A and C share the physical layer and ATM layer. Therefore, all links in the two areas
can be carried on common physical links.
NOTE
The RINT shown in Figure 3-10 refers to ATM interface boards UOIa/UOIc.
Table 3-2 IPoA data on the user plane of the ATM-based Iu-PS interface
Item Description
Local IP address of the IPoA PVC Device IP address on the ATM interface
(IPADDR (BSC6900, BSC6910)) board of the RNC
Peer IP address of the IPoA PVC IP address of the gateway on the SGSN side
(PEERIPADDR (BSC6900, BSC6910))
Route between the interface board carrying If the IP address of the interface board
the IPoA data and the network segment of carrying the IPoA data and the IP address of
the peer SGSN the peer SGSN are located on different
subnets, routes to the destination IP address
need to be configured at the RNC. DSTIP
(BSC6900, BSC6910) is the IP address of
the SGSN, and NEXTHOP (BSC6900,
BSC6910) is the IP address of the gateway
on the SGSN side.
NOTE
On the Iu-PS interface, the SGSN must be configured with routes to the network segment to which the
IP address of the RNC interface board belongs. The next hop is the gateway on the RNC side.
Otherwise, PS services cannot be provided.
The transport network layer of the ATM-based Iur interface consists of the following areas:
l Transport network layer control plane (area A)
l Transport network layer control plane (area B)
l Transport network layer user plane (area C)
NOTE
The RINT shown in Figure 3-13 refers to Iur IP interface boards, including GOUa/GOUc/GOUe/FG2a/
FG2c/FG2e for the BSC6900 and GOUc/GOUe/FG2c/EXOUa/FG2e for the BSC6910.
Figure 3-14 Mapping between the ATM cell and the E1 timeslots in UNI mode
The UNI mode has the characteristics of scrambling, line coding, 16-timeslot enabling, and
clock mode. The related parameters are as follows:
The settings of scrambling switch, line coding method, and 16-timeslot switch at both ends of
E1/T1 must be identical.
NOTE
Clock Mode
There are two clock modes on the RNC side:
l Common Transmit Clock (CTC): In CTC clock mode, all links in an IMA group share
one clock source. The clock source may be extracted from the same external clock or
from a link.
l Independent Transmit Clock (ITC): In ITC mode, the clocks used by the links within an
IMA group are derived from at least two clock sources. The loopback clock mode is a
special case of the ITC mode.
The clock mode on the RNC is not configurable, and the default clock mode on the RNC side
is CTC.
The clock mode on the NodeB side is specified by the parameter CLKM(UNI mode/fractional
mode)/CLKM(IMA mode). The clock mode settings at both ends of E1/T1 must be identical.
The coding methods of E1 port are HDB3 and AMI, and the HDB3 is recommended. HDB3
represents high-density bipolar code. It is not easy to be interfered, and the transmission
distance is several kilometers.
The coding methods of T1 port are B8ZS and AMI, and B8ZS is recommended. It helps
prevent clock signals from being lost, while AMI cannot perform this function.
If multiple E1/T1 trunks exist between the transmission end and the reception end and work
in IMA mode, such an IMA mode is called fractional IMA. In fractional IMA mode, an IMA
group contains multiple fractional ATM links.
The fractional ATM mode has the characteristics of scrambling, line coding, and clock mode.
For details about clock mode, see Clock Mode. The related parameters are as follows:
l Scrambling switch: specifies whether to enable scrambling.
l Line coding method: specifies the line coding method.
l E1/T1 timeslot: specifies the timeslot that transmits the ATM cell.
The settings of scrambling switch, line coding method, and E1/T1 timeslot at both ends of
E1/T1 must be identical.
The parameters corresponding to fractional mode are shown in Table 3-4.
NOTE
The IMA function is implemented by the IMA group, which is composed of either IMA links
or fractional IMA links.
All IMA links within an IMA group must be of the same type, either common IMA link or
fractional IMA link. If an IMA group is composed of fractional IMA links, the quantity of
timeslots carrying each fractional IMA link must be identical.
In IMA mode, ATM cells, IMA Control Protocol (ICP) cells, and filler cells form an IMA
frame to implement necessary controlling functions.
The length of an IMA frame, m, is defined during the setup of an IMA group. The parameter
FRMLEN (BSC6900, BSC6910)(at the RNC)/FRMLEN (at the NodeB) is used to specify
the length of an IMA frame.
Figure 3-18 shows an IMA frame. The mapping between the ATM cell and the physical link
(that is, the E1/T1 link) is similar to that in UNI mode.
The IMA mode has the characteristics of scrambling, line coding, 16-timeslot enabling, and
clock mode. The clock mode of an IMA group is defined from the perspective of an IMA
group rather than a single link. For details about clock mode, see Clock Mode. The related
parameters are as follows:
l Scrambling switch: specifies whether to enable scrambling.
l Line coding method: specifies the line coding method.
l 16-timeslot switch: specifies whether to use timeslot 16 or not.
The setting of scrambling switch, line coding method, and 16-timeslot switch at both ends of
E1/T1 must be identical.
The parameters corresponding to IMA mode are shown in Table 3-6.
NOTE
example shown in the following figure, the device cross-connects slots 2 and 3 on one E1/T1
to slots 4 and 8 on another E1/T1 respectively.
NOTE
Neither the source timeslot nor the target timeslot of a timeslot cross connection can be used by other
applications, such as fractional ATM, IMA, and UNI.
If an E1 link is configured with a timeslot cross connection, the E1 link cannot carry any IMA or UNI
link. The other timeslots on this E1 link can carry fractional ATM or fractional IMA links.
Note:
The BSC6910 does not support timeslot cross connection.
Time Variable Bit Rate (RT-VBR), Non-Real-Time Variable Bit Rate (NRT-VBR),
Unspecified Bit Rate (UBR), and UBR_PLUS (UBR+).
Table 3-7 describes the types of service.
Feedback on No No No No No
congestion
The ATM service type is also called ATM QoS class. The CBR, RT-VBR, NRT-VBR, or UBR
ATM QoS classes can be configured for AAL2 path, and the UBR+ ATM QoS class is
generally used for Iub OAM connection.
The service types carried on the AAL2 paths can be determined by running the ADD
ATMTRF command, and then the mapping between the service types and the transmission
resources for the adjacent node can be configured by running the ADD TRMMAP command.
Traffic Parameters
Traffic parameters refer to the parameters used by each PVC for flow control.
Parameter ID Description
ST (BSC6900, Indicates the type of service carried over ATM. CBR and RT-
BSC6910) VBR indicate real-time services, which are usually carried on the
user planes of the Iur, Iub, and Iu-CS interfaces. NRT-VBR and
UBR indicate non-real-time services, which are usually carried
on the user plane of the Iu-PS interface.
Parameter ID Description
PCR (BSC6900, Indicates the maximum rate of transmitting ATM cells. The value
BSC6910) of PCR (BSC6900, BSC6910) must be greater than that of SCR
(BSC6900, BSC6910).
SCR (BSC6900, Indicates the average rate of transmitting ATM cells over a long
BSC6910) time.
CDVT (BSC6900, Indicates the maximum tolerable variation in the unit of 0.1 μs.
BSC6910) NOTE
It is recommended that the cell delay variation tolerance (CDVT) of a
device connected to the NodeB be set to twice the CDVT of the NodeB,
thereby preventing packets from the NodeB being lost. The CDVT of the
NodeB is set to 10240 by default.
NOTE
l In practice, ATM traffic records should be negotiated between the local and the peer equipment.
l The ATM traffic parameters, such as PCR (BSC6900, BSC6910) and SCR (BSC6900, BSC6910),
should be configured depending on the traffic model in use.
l When configuring ATM traffic records for links, you need to consider the traffic on the interface
boards of the RNC.
3.8 AAL5
In ATM transport mode, AAL5 connections are used to carry the signaling on the Iub/Iur/Iu
interface (WRFD-05030105 Permanent AAL5 Connections for Control Plane Traffic). As
defined in 3GPP specifications, UNI-SAAL is used for control plane connections on the Iub
interface, and NNI-SAAL is used for control plane connections on the Iur and Iu interfaces.
The AAL5 connections for Iub/Iu-CS/Iur are set up by configuring the SAAL links.
You can run the ADD SAALLNK command to configure the AAL5 connections on the
Iub/Iur/Iu interface. On the RNC side, when an AAL5 connection is configured, the TXTRFX
(BSC6900, BSC6910) and RXTRFX (BSC6900, BSC6910) parameters need to be set. The
TXTRFX (BSC6900, BSC6910) and RXTRFX (BSC6900, BSC6910) parameters record the
ATM traffic, and they can be configured through the ADD ATMTRF command.
An SAAL link is carried on an ATM PVC. The parameters CARRYVPI (BSC6900,
BSC6910) and CARRYVCI (BSC6900, BSC6910) are used to identify the PVCs on the RNC
side, and the parameters VPI and VCI are used to identify the PVCs on the NodeB side. The
PVC identifier and other PVC attributes must be negotiated between the RNC and the peer
end.
The signaling messages carried on the UNI-SAAL links are classified into NCP, CCP, and
ALCAP, and the signaling messages carried on the NNI-SAAL links are MTP3, as described
in Table 3-11.
NCP The NCP carries common process messages of NBAP over the Iub
interface. An Iub interface has only one NCP.
CCP A CCP carries dedicated process messages of NBAP over the Iub interface.
An Iub interface may have multiple CCPs. The number of CCPs depends
on network planning.
ALCAP ALCAP is also called Q.AAL2. Typically, an Iub interface has one
ALCAP.
MTP3 MTP3 links are contained in an MTP3 link set. MTP3 links are carried on
the SAAL links of Network-to-Network Interface (NNI) type.
The AAL2 paths can be configured for the Iub/Iu-CS/Iur interface (WRFD-05030104
Dynamic AAL2 Connections in Iub/IuCS/Iur Interface).
Figure 3-22 shows the relationship between an AAL2 path and AAL2 connections on the Iub
interface.
l CBR
l RT-VBR
l NRT-VBR
l UBR
According to different types of service (R99, HSDPA, and HDUPA), the following types of
AAL2 path can be configured:
l R99
l HSPA
l SHARE
The AAL2 path can be configured through the ADD AAL2PATH command. On the RNC
side, when an AAL2 path is configured, the TXTRFX (BSC6900, BSC6910) and RXTRFX
(BSC6900, BSC6910) parameters need to be set. They determine the type of path. The
TXTRFX (BSC6900, BSC6910) and RXTRFX (BSC6900, BSC6910) parameters record the
ATM traffic, and they can be configured through the ADD ATMTRF command. For details,
see section 3.7.3 ATM Traffic Records.
An AAL2 path is carried on a PVC. The parameters VPI (BSC6900, BSC6910) and VCI
(BSC6900, BSC6910) are used to identify the PVCs. The PVC identifier and other PVC
attributes must be negotiated between the RNC and the peer end.
NOTE
l Even if the destination node and the adjacent node are the same, an AAL2 route needs to be
configured.
l The AAL2 route does not need to be configured for the adjacent node of the Iu-PS or Iub type.
3.10 MTP3
specify an MTP3 link set, and then run the command ADD MTP3LNK to add the MTP3
links by using the parameter SIGLKSX (BSC6900, BSC6910).
Figure 3-24 Example of connections between the MSC server and the RNC
in the MPS/EPS so that the signaling exchange can be reduced between the CPUS
subsystems.
IUCS R99 MSC DSP. The IUCS DSP has the control plane functions of
both radio network layer and transport network layer on the Iu-CS
interface.
IUCS_ALCAP R4 MGW DSP. The IUCS_ALCAP DSP has the control plane
functions of the transport network layer on the Iu-CS interface.
IUCS_RANAP R4 MSC server DSP. The IUCS_RANAP DSP has the control plane
functions of the radio network layer on the Iu-CS interface.
Figure 3-25 Relationship between signaling link mask and signaling route mask
3.12 F5
Huawei supports operations on ATM OAM F5 end-to-end flows specified in ITU I.610
(WRFD-05030110 F5):
l Fault management
– AIS: alarm indication signal
– RDI: remote defect indication
– CC: continuity check and loopback
l Performance management
– Forward monitoring
– Backward reporting
l Activation and deactivation
The CC can be activated to monitor the end-to-end AAL2 path virtual connect link (VCL) and
Iu-PS user plane VCL. When one VCL for AAL2 path or Iu-PS GTPU is loss of continuity
(LOC), AIS, or RDI, this VCL is blocked. Then the service is established on other alternative
VCLs to prevent the failure of the call. You can run the ACT VCLCC command to activate
the CC function and the DEA VCLCC command to deactivate the CC function. When the
parameter VCLTYPE is set to CC, the CC function is activated.
Huawei also supports proprietary delay detection function. When an NE receives a detection
start command from the NMS, it starts detecting delay on the current AAL2 link or AAL5
link and periodically reports the delay to the NMS. The 8-byte reserved IE (LB IE) in the
loopback message is used to store the message transmission time. When an NE receives the
loopback message, it calculates the delay based on the time difference between transmission
and reception.
ATM transmission resources can be classified into physical resources, logical ports, resource
groups, and paths. The transmission resources for Iub/Iu/Iur interfaces vary according to
different networking. Huawei supports the following types of ATM transmission:
l ATM over E1T1 on Iub interface (WRFD-05030101 ATM over E1T1 on Iub Interface)
The BSC6910 does not support this feature.
l ATM over channelized STM-1/OC-3 on Iub interface (WRFD-05030102 ATM over
Channelized STM-1/OC-3 on Iub Interface)
l ATM over Non-channelized STM-1/OC-3c on Iub/Iu/Iur Interface (WRFD-05030103
ATM over Non-channelized STM-1/OC-3c on Iub/Iu/Iur Interface)
For details about the ATM transmission resources, see "Transmission Resources" in the
Transmission Resource Management Feature Parameter Description.
For ATM transport, Huawei provides the following transmission resource management:
l Admission control (provided by WRFD-05030106 Call Admission Based on Used
AAL2 Path Bandwidth), which is used to allow more users to be admitted with the QoS
guaranteed.
l Transmission resource mapping, in which the CBR, RT-VBR, NRT-VBR, and UBR
ATM QoS classes are used to implement differentiated services.
l Iub overbooking (provided by WRFD-050405 Overbooking on ATM Transmission and
WRFD-050406 ATM QoS Introduction on Hub Node B (Overbooking on Hub Node B
Transmission)), which is used to improve the usage efficiency on ATM transport
scenario
For details about admission control, transmission resource mapping, and Iub overbooking, see
the Transmission Resource Management Feature Parameter Description.
6 Engineering Guidelines
6.1.1 Requirements
l Other features
None
l Hardware
None
The BBU3910C does not support this feature.
l License
This feature is not under license control.
l Other requirements
The ATM transmission network is well configured.
6.1.2 Procedure
Activation
l On the RNC side
a. Run the RNC MML command ADD ADJNODE (CME single configuration:
NodeB Configuration Express > IUB_RNC > ATM Transport > Adjacent
Node, IUR Configuration Express > ATM Transport > Adjacent Node, IUCS
Configuration Express > ATM Transport > Adjacent Node; CME batch
modification center: not supported) to add an adjacent node. Set the parameter
Adjacent Node Type to IUB, IUR, or IUCS, and the parameter Transport Type to
ATM. If the node is the lowest leaf node of the switching network, set the
parameter Is Root Node to YES; otherwise, set the parameter Is Root Node to NO.
NOTE
For an adjacent node on the Iur or Iu-CS interface, the parameter Adjacent Node Type of its
upper-level hub node must be NNI_AAL2SWITCH; for an adjacent node on the Iub interface,
the parameter Adjacent Node Type of its upper-level hub node must be UNI_AAL2SWITCH.
b. Run the RNC MML command ADD AAL2PATH (CME single configuration:
NodeB Configuration Express > IUB_RNC > ATM Transport > AAL2 Path,
IUCS Configuration Express > ATM Transport > AAL2 Path, IUR
Configuration Express > ATM Transport > AAL2 Path; CME batch
modification center: not supported) to add an AAL2 path. The parameters
CARRYVPI and CARRYVCI must be consistent with those of the AAL2 path
configured on the peer end.
l On the NodeB side
For details about configuration on the NodeB side, obtain the documentation 3900 Series
Base Station Product Documentation and navigate in the following sequence: 3900
Series Base Station Initial Configuration (CME-based) > Creating Base Stations >
Creating NodeBs > Creating a Single NodeB > Configuring NodeB Transport Data
> Configuring ATM Transport Data on the NodeB Side.
Verification
Step 1 Run the RNC MML command DSP AAL2PATH to query the status of the AAL2 path on the
Iub interface.
Step 2 Run the NodeB MML command DSP AAL2PATH to query the status of the AAL2 path on
the Iub.
Step 3 In the Iub/Iu-CS ATM transmission scenario, a UE in idle state camps on CELL1 and the
control plane is correctly configured. Originate the speech and data services. If the service
access is normal, the AAL2 path on the Iub/Iu-CS interface is set up successfully.
Step 4 Optional: In the ATM transmission scenario on the Iur interface, a UE in idle state camps on
CELL1 and the control plane is correctly configured. Originate a cross-Iur handover. If the
handover is successful, the AAL2 path on the Iur interface is set up successfully.
----End
Deactivation
Step 1 Run the RNC MML command RMV AAL2PATH (CME single configuration: NodeB
Configuration Express > IUB_RNC > ATM Transport > AAL2 Path, IUCS
Configuration Express > ATM Transport > AAL2 Path, IUR Configuration Express >
ATM Transport > AAL2 Path; CME batch modification center: not supported) to delete an
AAL2 path.
Step 2 Run the RNC MML command RMV ADJNODE (CME single configuration: NodeB
Configuration Express > IUB_RNC > ATM Transport > Adjacent Node, IUR
Configuration Express > ATM Transport > Adjacent Node, IUCS Configuration
Express > ATM Transport > Adjacent Node; CME batch modification center: not
supported) to delete an ATM adjacent node.
Step 3 Run the NodeB MML command RMV AAL2PATH (CME single configuration: ATM
Transport Layer > AAL2path) to delete an AAL2 path on the NodeB side.
----End
6.2.1 Requirements
l Other features
None
l Hardware
None
The BBU3910C does not support this feature.
l License
This feature is not under license control.
l Other requirements
The equipment data has been configured for the ATM transmission on the Iub/Iu/Iur
interface.
6.2.2 Procedure
Activation Procedure
Step 1 Run the RNC MML command ADD SAALLNK (CME single configuration: NodeB
Configuration Express > IUB_RNC > ATM Transport > SAAL Signaling Link, IUCS
Configuration Express > ATM Transport > SAAL Signaling Link, IUR Configuration Express
> ATM Transport > SAAL Signaling Link; CME batch modification center: not supported) to
add an SAAL link. If the interface is Iub, set the parameter Interface type to UNI. If the
interface is Iu or Iur, set Interface type to NNI.
Step 2 Optional: Run the RNC MML command ADD UNCP (CME single configuration: NodeB
Configuration Express > IUB_RNC > ATM Transport > NCP Link; CME batch modification
center: not supported) to add a NodeB Control Port (NCP) link.
Step 3 Optional: Run the RNC MML command ADD UCCP (CME single configuration: NodeB
Configuration Express > IUB_RNC > ATM Transport > CCP Link; CME batch modification
center: not supported) to add a Communication Control Port (CCP) link.
----End
NOTE:
An SAAL link can carry only one NCP or CCP link. Therefore, choose to perform step 2 or
step 3 based on the actual situation.
Verification Procedure
Run the RNC MML command DSP SAALLNK to query the status of the SAAL link.
Deactivation Procedure
NOTE:
An SAAL link can carry only one NCP or CCP link. Therefore, choose to remove the NCP or
CCP link carried by the SAAL link, based on the actual situation.
Step 1 Optional: Run the RNC MML command RMV UNCP (CME single configuration: NodeB
Configuration Express > IUB_RNC > ATM Transport > NCP Link; CME batch modification
center: not supported) to remove the NCP link carried by the SAAL link.
Step 2 Optional: Run the RNC MML command RMV UCCP (CME single configuration: NodeB
Configuration Express > IUB_RNC > ATM Transport > CCP Link; CME batch modification
center: not supported) to remove the CCP link carried by the SAAL link.
Step 3 Run the RNC MML command RMV SAALLNK (CME single configuration: NodeB
Configuration Express > IUB_RNC > ATM Transport > SAAL Signaling Link, IUCS
Configuration Express > ATM Transport > SAAL Signaling Link, IUR Configuration Express
> ATM Transport > SAAL Signaling Link; CME batch modification center: not supported) to
remove the SAAL link.
----End
6.3.1 Requirements
l Other features
None
l Hardware
None
The BBU3910C does not support this feature.
l License
This feature is not under license control.
6.3.2 Procedure
Activation
Step 1 Run the RNC MML command ADD ATMTRF (CME single configuration: NodeB
Configuration Express > IUB_RNC > ATM Transport > ATM Traffic Record; CME batch
modification center: not supported) to set parameters to appropriate values. For example, set
Service type to NRTVBR, Peak cell rate to 100, and Sustainable cell rate to 80.
Step 2 Run the RNC MML command ADD AAL2PATH (CME single configuration: NodeB
Configuration Express > IUB_RNC > ATM Transport > AAL2 Path; CME batch modification
center: not supported) to add an ATM Adaptation Layer type 2 (AAL2) path. In this step, set
TXTRFX and RXTRFX in accordance with the settings in step 1.
----End
Verification
Step 1 Assume that the verification is based on the preceding parameter settings and the peer end is
configured with the corresponding AAL2 path link. Originate a PS interactive service. If the
subscribed rate is 64 kbit/s, the UE successfully accesses the network.
Step 2 Run the RNC MML command DSP AAL2PATH to view that the used bandwidth of the path
is about 30 kbit/s, which is the admission bandwidth of the control plane.
Step 3 Originate consecutive multiple PS interactive services when the service established in step 1
is not released. If the subscribed rate is 64 kbit/s, the third PS interactive service fails to be set
up.
----End
Deactivation
This feature does not need to be deactivated.
6.4.1 Requirements
l Other features
None
l Hardware
None
The BBU3910C does not support this feature.
l License
This feature is not under license control.
6.4.2 Procedure
Activation Procedure
Run the RNC MML command ADD ATMTRF (CME single configuration: NodeB
Configuration Express > IUB_RNC > ATM Transport > ATM Traffic Record; CME batch
modification center: not supported) to add an ATM traffic record. To add more ATM traffic
records, run this command repeatedly.
Verification Procedure
Ensure that an AAL2 path using the ATM traffic record added in the activation procedure and
TRMMAP of the AAL2 path have been set before the verification.
Step 3 Check TXTRFX of the AAL2 path corresponding to the path ID in the QAAL2 Establish
request message.
The expected result is that the value of TXTRFX is consistent with that in the ADD
ATMTRF command.
----End
Deactivation Procedure
Step 1 Run the RNC MML command RMV AAL2PATH (CME single configuration: NodeB
Configuration Express > IUB_RNC > ATM Transport > AAL2 Path, IUCS Configuration
Express > ATM Transport > AAL2 Path, IUR Configuration Express > ATM Transport >
AAL2 Path; CME batch modification center: not supported) to delete an AAL2 path using an
ATM traffic record. To delete more AAL2 paths, run this command repeatedly.
Step 2 Run the RNC MML command RMV ATMTRF (CME single configuration: NodeB
Configuration Express > IUB_RNC > ATM Transport > ATM Traffic Record; CME batch
modification center: not supported) to delete an ATM traffic record. To delete more ATM
traffic records, run this command repeatedly.
----End
6.5 WRFD-05030110 F5
This chapter describes how to activate, verify, and deactivate the basic feature
WRFD-05030110 F5. This feature cannot be configured using the CME.
6.5.1 Requirements
l Other features
None
l Hardware
– Dependency on the RNC
None
– Dependency on the NodeB
Only 3900 and 5900 series macro base stations and LampSite base stations support
delay detection based on the IE "LB".
The BBU3910C does not support this feature.
l License
This feature is not under license control.
l Other requirements
– For detailed RNC configurations, see BSC6900 UMTS Initial Configuration Guide
or BSC6910 UMTS Initial Configuration Guide.
– An SAAL link, AAL2 path, or IP over ATM (IPoA) PVC link has been configured.
6.5.2 Procedure
Activation Procedure
Step 1 Run the RNC MML command ACT VCLCC to activate the VCL CC or loopback function
for a link. To activate the function for multiple links, run this command repeatedly. There are
three types of links, that is, SAALLNK, AAL2PATH, and IPOAPVC.
Step 2 Run the RNC MML command ACT VCLPM to activate the VCL PM function for a link. To
activate the function for multiple links, run this command repeatedly. There are three types of
links, that is, SAALLNK, AAL2PATH, and IPOAPVC.
----End
Verification Procedure
Step 1 Run the RNC MML command DSP VCLCC to query the CC result of a VCL.
l If the VCL CC is activated and the PVC is functional, the SINK activated state and
SOURCE activated state are UP, and LOC, AIS, and RDI alarm state is normal.
l If the loopback is activated and the PVC is functional, the loopback query result is UP,
and LOC, AIS, and RDI alarm state is normal.
Step 2 Run the RNC MML command DSP VCLPM to query the PM result of a VCL.
l If the VCL PM is activated, the SINK activated state and SOURCE activated state are
PM_UP, and PM Active Fail Alarm is Normal.
----End
Deactivation Procedure
Step 1 Run the RNC MML command DEA VCLCC to deactivate the VCL CC or loopback function
for a link. To deactivate the function for multiple links, run this command repeatedly. There
are three types of links, that is, SAALLNK, AAL2PATH, and IPOAPVC.
Step 2 Run the RNC MML command DEA VCLPM to deactivate the VCL PM for a link. To
deactivate the function for multiple links, run this command repeatedly. There are three types
of links, that is, SAALLNK, AAL2PATH, and IPOAPVC.
----End
6.6.1 Requirements
l Other features
None
l Hardware
None
The BBU3910C does not support this feature.
l License
This feature is not under license control.
l Other requirements
For detailed RNC configurations, see BSC6900 UMTS Initial Configuration Guide or
BSC6910 UMTS Initial Configuration Guide.
6.6.2 Procedure
Activation Procedure
Run the MML command ADD ATMTRF (CME single configuration: NodeB Configuration
Express > IUB_RNC > ATM Transport > ATM Traffic Record; CME batch modification
center: not supported) to add an ATM traffic record of the UBR+ class. To add more ATM
traffic records, run this command repeatedly.
Verification Procedure
Run the MML command LST ATMTRF to query the ATM traffic configuration.
Expected result: The query result is consistent with the configuration information.
Deactivation Procedure
Run the MML command RMV ATMTRF (CME single configuration: NodeB Configuration
Express > IUB_RNC > ATM Transport > ATM Traffic Record; CME batch modification
center: not supported) to delete an ATM traffic record of the UBR+ class. To delete more
ATM traffic records, run this command repeatedly.
7 Parameters
NEXTH BSC691 ADD WRFD- Iu/Iur IP Meaning: IP address of the next hop.
OP 0 IPRT 150244 Transmi GUI Value Range: Valid IP Address
MOD WRFD- ssion
Based Unit: None
IPRT 050107
on Actual Value Range: Valid IP Address
RMV WRFD- Dynami
IPRT 150243 Default Value: None
c Load
Balance
IP
routing
Based
Hub
Node B
Iub IP
Transmi
ssion
Based
on
Dynami
c Load
Balance
TS16EN BSC690 SET WRFD- ATM Meaning: This parameter specifies whether to use
ABLE 0 E1T1 0503010 over timeslot 16, or not.
1 E1T1 on GUI Value Range: OFF(OFF), ON(ON)
Iub
Interface Unit: None
Actual Value Range: OFF, ON
Default Value: OFF(OFF)
SCRAM BTS390 ADD WRFD- ATM Meaning: Indicates whether scrambling is applied to
0, UNILN 0503010 over the UNI link.
BTS390 K 1 E1T1 on GUI Value Range: DISABLE(Disable),
0 LST Iub ENABLE(Enable)
WCDM UNILN Interface
A, Unit: None
K
BTS590 Actual Value Range: DISABLE, ENABLE
0, Default Value: ENABLE(Enable)
BTS590
0
WCDM
A
LNCOD BTS390 ADD WRFD- ATM Meaning: Indicates the line coding mode of an E1/T1
E 0, E1T1 0503010 over port.
BTS390 SET 1 E1T1 on GUI Value Range: HDB3(E1 HDB3 Code),
0 E1T1 WRFD- Iub AMI(E1/T1 AMI Code), B8ZS(T1 B8ZS Code)
WCDM 050411 Interface
A, LST Unit: None
E1T1 Fraction
BTS390 al IP Actual Value Range: HDB3, AMI, B8ZS
0 LTE, Function Default Value: None
BTS590 on Iub
0, Interface
BTS590
0
WCDM
A,
BTS590
0 LTE
TS16 BTS390 ADD WRFD- ATM Meaning: Indicates whether a UNI link can use
0, UNILN 0503010 over timeslot 16 among the 32 timeslots of an E1 port.
BTS390 K 1 E1T1 on GUI Value Range: DISABLE(Disable),
0 LST Iub ENABLE(Enable)
WCDM UNILN Interface
A, Unit: None
K
BTS590 Actual Value Range: DISABLE, ENABLE
0, Default Value: DISABLE(Disable)
BTS590
0
WCDM
A
CLKM BTS390 ADD WRFD- IMA for Meaning: Indicates the clock mode of the IMA group.
0, IMAGR 050304 E1T1 or Links in an IMA group may pass through different
BTS390 P Channel transport networks. As a result, links in the IMA
0 MOD ized group may use different clock sources for
WCDM IMAGR STM-1/ synchronization. It is recommended that the IMA
A, P OC-3 on group work in Independent Transmit Clock (ITC)
BTS590 Iub mode.
0, LST Interface
IMAGR GUI Value Range: CTC(Common Transmit Clock),
BTS590 ITC(Independent Transmit Clock)
0 P
WCDM Unit: None
A Actual Value Range: CTC, ITC
Default Value: ITC(Independent Transmit Clock)
SCRAM BTS390 ADD WRFD- ATM Meaning: Indicates whether scrambling is applied to
0, FRAAT 0503010 over the fractional ATM link.
BTS390 M 1 E1T1 on GUI Value Range: DISABLE(Disable),
0 LST Iub ENABLE(Enable)
WCDM FRAAT Interface
A, Unit: None
M
BTS590 Actual Value Range: DISABLE, ENABLE
0, Default Value: ENABLE(Enable)
BTS590
0
WCDM
A
TSN BTS390 ADD WRFD- ATM Meaning: Indicates the number of the ET/T1 timeslot
0, FRAAT 0503010 over that carries the fractional ATM link.
BTS390 M 1 E1T1 on GUI Value Range: TS1(Time Slot 1), TS2(Time Slot
0 DSP Iub 2), TS3(Time Slot 3), TS4(Time Slot 4), TS5(Time
WCDM DHCPR Interface Slot 5), TS6(Time Slot 6), TS7(Time Slot 7),
A, SLT TS8(Time Slot 8), TS9(Time Slot 9), TS10(Time
BTS590 Slot10), TS11(Time Slot11), TS12(Time Slot12),
0, LST
FRAAT TS13(Time Slot13), TS14(Time Slot14), TS15(Time
BTS590 Slot15), TS16(Time Slot16), TS17(Time Slot17),
0 M
TS18(Time Slot18), TS19(Time Slot19), TS20(Time
WCDM Slot20), TS21(Time Slot21), TS22(Time Slot22),
A TS23(Time Slot23), TS24(Time Slot24), TS25(Time
Slot25), TS26(Time Slot26), TS27(Time Slot27),
TS28(Time Slot28), TS29(Time Slot29), TS30(Time
Slot30), TS31(Time Slot31)
Unit: None
Actual Value Range: TS1, TS2, TS3, TS4, TS5, TS6,
TS7, TS8, TS9, TS10, TS11, TS12, TS13, TS14,
TS15, TS16, TS17, TS18, TS19, TS20, TS21, TS22,
TS23, TS24, TS25, TS26, TS27, TS28, TS29, TS30,
TS31
Default Value: None
FRMLE BSC690 ADD WRFD- ATM Meaning: Frame length. A longer frame improves the
N 0 IMAGR 050105 Switchin transmission efficiency, but at the same time reduces
P WRFD- g Based the sensitivity to errors.
MOD 050304 Hub GUI Value Range: D32, D64, D128, D256
IMAGR Node B
Unit: None
P IMA for
E1T1 or Actual Value Range: D32, D64, D128, D256
Channel Default Value: D128
ized
STM-1/
OC-3 on
Iub
Interface
FRMLE BSC691 ADD WRFD- ATM Meaning: Frame length. A longer frame improves the
N 0 IMAGR 050105 Switchin transmission efficiency, but at the same time reduces
P WRFD- g Based the sensitivity to errors.
MOD 050304 Hub GUI Value Range: D32, D64, D128, D256
IMAGR Node B
Unit: None
P IMA for
E1T1 or Actual Value Range: D32, D64, D128, D256
Channel Default Value: D128
ized
STM-1/
OC-3 on
Iub
Interface
FRMLE BTS390 ADD WRFD- IMA for Meaning: Indicates the length of the frame used for
N 0, IMAGR 050304 E1T1 or data transmission on the IMA link in the IMA group.
BTS390 P Channel A larger value of this parameter results in higher
0 MOD ized efficiency but lower sensitivity to bit errors.
WCDM IMAGR STM-1/ GUI Value Range: D32(D32), D64(D64),
A, P OC-3 on D128(D128), D256(D256)
BTS590 Iub
0, DSP Interface Unit: None
BTS590 DHCPR Actual Value Range: D32, D64, D128, D256
0 SLT
Default Value: D128(D128)
WCDM LST
A IMAGR
P
SCRAM BTS390 ADD WRFD- IMA for Meaning: Indicates whether scrambling is applied to
0, IMAGR 050304 E1T1 or the IMA group.
BTS390 P Channel GUI Value Range: DISABLE(Disable),
0 MOD ized ENABLE(Enable)
WCDM IMAGR STM-1/
A, OC-3 on Unit: None
P
BTS590 Iub Actual Value Range: DISABLE, ENABLE
0, LST Interface
IMAGR Default Value: ENABLE(Enable)
BTS590
0 P
WCDM
A
TS16 BTS390 ADD WRFD- IMA for Meaning: Indicates whether to enable E1 timeslot 16.
0, IMAGR 050304 E1T1 or GUI Value Range: DISABLE(Disable),
BTS390 P Channel ENABLE(Enable)
0 MOD ized
WCDM STM-1/ Unit: None
IMAGR
A, P OC-3 on Actual Value Range: DISABLE, ENABLE
BTS590 Iub Default Value: DISABLE(Disable)
0, LST Interface
BTS590 IMAGR
0 P
WCDM
A
DSTPO BSC690 ADD None None Meaning: Destination of the timeslot cross connection
RTNO 0 TSCRO GUI Value Range: 0~335
SS
Unit: None
Actual Value Range: 0~335
Default Value: None
ST BSC690 ADD WRFD- HSDPA Meaning: Service type of the ATM. When traffic
0 ATMTR 010610 Introduc index is used by the SAAL, IPoA PVC, VPCLCX
F WRFD- tion link, or AAL2 path of the AOUc/UOIc board, the
050305 Package service type UBR and UBR_PLUS must be
UBR+ configured with the PCR.
WRFD-
050301 ATM GUI Value Range: UBR_PLUS, UBR, NRTVBR,
QoS RTVBR, CBR
WRFD- Class
010697 Unit: None
ATM Actual Value Range: UBR_PLUS, UBR, NRTVBR,
Transmi RTVBR, CBR
ssion
Introduc Default Value: None
tion
Package
E-
DPCCH
Boostin
g
ST BSC691 ADD WRFD- HSDPA Meaning: Service type of the ATM. When traffic
0 ATMTR 010610 Introduc index is used by the SAAL, IPoA PVC, or AAL2 path
F WRFD- tion of the AOUc/UOIc board, the service type UBR and
010697 Package UBR_PLUS must be configured with the PCR.
E- GUI Value Range: UBR_PLUS, UBR, NRTVBR,
DPCCH RTVBR, CBR
Boostin Unit: None
g
Actual Value Range: UBR_PLUS, UBR, NRTVBR,
RTVBR, CBR
Default Value: None
PCR BSC690 ADD WRFD- HSDPA Meaning: Peak rate of the ATM traffic. When the
0 ATMTR 010610 Introduc ATM traffic record indexes corresponding to the
F WRFD- tion service type UBR, RTVBR or NRTVBR are used by
050305 Package AOUa, AEUa or UOIa(ATM), the peak cell rate
UBR+ (PCR), if configured, must be lower than 60000
WRFD- KBIT/S or 141510 CELL/S.
010697 ATM
QoS GUI Value Range: 30~353207
WRFD- Class
050301 Unit: None
E- Actual Value Range: 30~353207
WRFD- DPCCH
0503010 Boostin Default Value: None
7 g
ATM
Transmi
ssion
Introduc
tion
Package
CBR, rt-
VBR,
nrt-
VBR,
UBR
ATM
QoS
Classes
PCR BSC691 ADD WRFD- HSDPA Meaning: Peak rate of the ATM traffic.
0 ATMTR 010610 Introduc GUI Value Range: 30~353207
F WRFD- tion
Package Unit: None
050305
UBR+ Actual Value Range: 30~353207
WRFD-
010697 ATM Default Value: None
QoS
WRFD- Class
050301
E-
WRFD- DPCCH
0503010 Boostin
7 g
ATM
Transmi
ssion
Introduc
tion
Package
CBR, rt-
VBR,
nrt-
VBR,
UBR
ATM
QoS
Classes
SCR BSC690 ADD WRFD- HSDPA Meaning: Maximum average cell rate of a VBR
0 ATMTR 010610 Introduc service source. The VBR is short for Variable Bit
F WRFD- tion Rate. The average cell rate is the average value of cell
050305 Package rates for a service source on a physical service access
UBR+ point (PHY-SAP) within a period of time. This
WRFD- parameter is calculated using the following formula:
010697 ATM
QoS SCR = 1/Ts, where, Ts indicates the minimum average
WRFD- Class interval between sending ATM cells.
050301 GUI Value Range: 30~353207
E-
WRFD- DPCCH Unit: None
0503010 Boostin
7 Actual Value Range: 30~353207
g
Default Value: None
ATM
Transmi
ssion
Introduc
tion
Package
CBR, rt-
VBR,
nrt-
VBR,
UBR
ATM
QoS
Classes
SCR BSC691 ADD WRFD- HSDPA Meaning: Maximum average cell rate of a VBR
0 ATMTR 010610 Introduc service source. The VBR is short for Variable Bit
F WRFD- tion Rate. The average cell rate is the average value of cell
050305 Package rates for a service source on a physical service access
UBR+ point (PHY-SAP) within a period of time. This
WRFD- parameter is calculated using the following formula:
010697 ATM
QoS SCR = 1/Ts, where, Ts indicates the minimum average
WRFD- Class interval between sending ATM cells.
050301 GUI Value Range: 30~353207
E-
WRFD- DPCCH Unit: None
0503010 Boostin
7 Actual Value Range: 30~353207
g
Default Value: None
ATM
Transmi
ssion
Introduc
tion
Package
CBR, rt-
VBR,
nrt-
VBR,
UBR
ATM
QoS
Classes
MCR BSC690 ADD WRFD- HSDPA Meaning: Minimum guarantee rate of the ATM
0 ATMTR 010610 Introduc traffic.The "Minimum cell rate" of the AOUc or UOIc
F WRFD- tion board cannot be greater than 13.8 Mbit/s.
050305 Package GUI Value Range: 30~70754
WRFD- UBR+ Unit: None
010697 ATM
QoS Actual Value Range: 30~70754
WRFD- Class Default Value: None
050301
E-
WRFD- DPCCH
0503010 Boostin
7 g
ATM
Transmi
ssion
Introduc
tion
Package
CBR, rt-
VBR,
nrt-
VBR,
UBR
ATM
QoS
Classes
MCR BSC691 ADD WRFD- HSDPA Meaning: Minimum guarantee rate of the ATM
0 ATMTR 010610 Introduc traffic.The "Minimum cell rate" of the AOUc or UOIc
F WRFD- tion board cannot be greater than 13.8 Mbit/s.
050305 Package GUI Value Range: 30~70754
WRFD- UBR+ Unit: None
010697 ATM
QoS Actual Value Range: 30~70754
WRFD- Class Default Value: None
050301
E-
WRFD- DPCCH
0503010 Boostin
7 g
ATM
Transmi
ssion
Introduc
tion
Package
CBR, rt-
VBR,
nrt-
VBR,
UBR
ATM
QoS
Classes
MBS BSC690 ADD WRFD- HSDPA Meaning: Maximum burst size (MBS). For details
0 ATMTR 010610 Introduc about this parameter, see TM4.1 protocol.
F WRFD- tion GUI Value Range: 3~10000
050305 Package
Unit: cell/s
WRFD- UBR+
ATM Actual Value Range: 3~10000
050301
QoS Default Value: None
WRFD- Class
010697
ATM
Transmi
ssion
Introduc
tion
Package
E-
DPCCH
Boostin
g
MBS BSC691 ADD WRFD- HSDPA Meaning: Maximum burst size (MBS). For details
0 ATMTR 010610 Introduc about this parameter, see TM4.1 protocol.
F WRFD- tion GUI Value Range: 3~10000
010697 Package
Unit: cell/s
E-
DPCCH Actual Value Range: 3~10000
Boostin Default Value: None
g
CDVT BSC690 ADD WRFD- HSDPA Meaning: Tolerable delay jitter. For details about this
0 ATMTR 010610 Introduc parameter, see TM4.1 protocol.
F WRFD- tion GUI Value Range: 1024~212000
050305 Package
Unit: 100ns
WRFD- UBR+
ATM Actual Value Range: 102400~21200000
050301
QoS Default Value: 1024
WRFD- Class
010697
ATM
Transmi
ssion
Introduc
tion
Package
E-
DPCCH
Boostin
g
CDVT BSC691 ADD WRFD- HSDPA Meaning: Tolerable delay jitter. For details about this
0 ATMTR 010610 Introduc parameter, see TM4.1 protocol.
F WRFD- tion GUI Value Range: 1024~212000
010697 Package
Unit: 100ns
E-
DPCCH Actual Value Range: 102400~21200000
Boostin Default Value: 1024
g
CDVT BTS390 ADD WRFD- Dynami Meaning: Indicates the cell delay variation tolerance.
0, AAL2P 0503010 c AAL2 The value of this parameter is subject to the actual
BTS390 ATH 4 Connect network. Setting the parameter to an improper value
0 MOD ions in affects the service quality.
WCDM AAL2P Iub/ GUI Value Range: 1024~13300000
A, ATH IuCS/Iur
BTS590 Interface Unit: 0.1microsecond
0, LST Actual Value Range: 102.4~1330000, step:0.1
BTS590 AAL2P
ATH Default Value: 10240
0
WCDM
A
REMAR BSC690 ADD None None Meaning: Purpose description of the ATM traffic
K 0 ATMTR record
F GUI Value Range: 0~255 characters
MOD Unit: None
ATMTR
F Actual Value Range: 0~255 characters
Default Value: -
REMAR BSC691 ADD WRFD- HSDPA Meaning: Purpose description of the ATM traffic
K 0 ATMTR 010610 Introduc record
F WRFD- tion GUI Value Range: 0~255 characters
MOD 010697 Package
Unit: None
ATMTR E-
F DPCCH Actual Value Range: 0~255 characters
Boostin Default Value: -
g
TXTRF BSC690 ADD WRFD- Permane Meaning: TX traffic record index of the SAAL link.
X 0 SAALL 0503010 nt For details, see "ADD ATMTRF".
NK 5 AAL5 GUI Value Range: 100~1999
MOD WRFD- Connect
ions for Unit: None
SAALL 050301
NK Control Actual Value Range: 100~1999
Plane Default Value: None
Traffic
ATM
Transmi
ssion
Introduc
tion
Package
TXTRF BSC691 ADD WRFD- Permane Meaning: TX traffic record index of the SAAL link.
X 0 SAALL 0503010 nt For details, see "ADD ATMTRF".
NK 5 AAL5 GUI Value Range: 100~1999
MOD WRFD- Connect
ions for Unit: None
SAALL 050301
NK Control Actual Value Range: 100~1999
Plane Default Value: None
Traffic
ATM
Transmi
ssion
Introduc
tion
Package
RXTRF BSC690 ADD WRFD- Permane Meaning: Index of traffic received over an SAAL link.
X 0 SAALL 0503010 nt For details, see "ADD ATMTRF".
NK 5 AAL5 GUI Value Range: 100~1999
MOD WRFD- Connect
ions for Unit: None
SAALL 050301
NK Control Actual Value Range: 100~1999
Plane Default Value: None
Traffic
ATM
Transmi
ssion
Introduc
tion
Package
RXTRF BSC691 ADD WRFD- Permane Meaning: Index of traffic received over an SAAL link.
X 0 SAALL 0503010 nt For details, see "ADD ATMTRF".
NK 5 AAL5 GUI Value Range: 100~1999
MOD WRFD- Connect
ions for Unit: None
SAALL 050301
NK Control Actual Value Range: 100~1999
Plane Default Value: None
Traffic
ATM
Transmi
ssion
Introduc
tion
Package
CARRY BSC690 ADD WRFD- ATM/IP Meaning: VPI value of the SAAL out RNC.
VPI 0 SAALL 050404 Dual GUI Value Range: 0~4095
NK WRFD- Stack
Node B Unit: None
MOD 0503010
SAALL 5 Permane Actual Value Range: 0~4095
NK WRFD- nt Default Value: None
050301 AAL5
Connect
ions for
Control
Plane
Traffic
ATM
Transmi
ssion
Introduc
tion
Package
CARRY BSC691 ADD WRFD- ATM/IP Meaning: VPI value of the SAAL out RNC.
VPI 0 SAALL 050404 Dual GUI Value Range: 0~4095
NK WRFD- Stack
Node B Unit: None
MOD 0503010
SAALL 5 Permane Actual Value Range: 0~4095
NK WRFD- nt Default Value: None
050301 AAL5
Connect
ions for
Control
Plane
Traffic
ATM
Transmi
ssion
Introduc
tion
Package
CARRY BSC690 ADD WRFD- ATM/IP Meaning: VCI value of the SAAL out RNC.
VCI 0 SAALL 050404 Dual GUI Value Range: 32~65535
NK WRFD- Stack
Node B Unit: None
MOD 0503010
SAALL 5 Permane Actual Value Range: 32~65535
NK WRFD- nt Default Value: None
050301 AAL5
Connect
ions for
Control
Plane
Traffic
ATM
Transmi
ssion
Introduc
tion
Package
CARRY BSC691 ADD WRFD- ATM/IP Meaning: VCI value of the SAAL out RNC.
VCI 0 SAALL 050404 Dual GUI Value Range: 32~65535
NK WRFD- Stack
Node B Unit: None
MOD 0503010
SAALL 5 Permane Actual Value Range: 32~65535
NK WRFD- nt Default Value: None
050301 AAL5
Connect
ions for
Control
Plane
Traffic
ATM
Transmi
ssion
Introduc
tion
Package
VPI BTS390 ADD WRFD- ATM Meaning: Indicates the Virtual Path Identifier (VPI),
0, SAALL 0503010 over which is used for VP routing. A virtual path contains
BTS390 NK 1 E1T1 on multiple virtual channels.
0 LST WRFD- Iub GUI Value Range: 0~255
WCDM SAALL 0503010 Interface
A, Unit: None
NK 3 ATM
BTS590 over Actual Value Range: 0~255
0, Non- Default Value: None
BTS590 channeli
0 zed
WCDM STM-1/
A OC-3c
on
Iub/Iu/Iu
r
Interface
VCI BTS390 ADD WRFD- ATM Meaning: Indicates the Virtual Channel Identifier
0, SAALL 0503010 over (VCI), which is used for VC routing.
BTS390 NK 1 E1T1 on GUI Value Range: 32~511
0 LST WRFD- Iub
WCDM Interface Unit: None
SAALL 0503010
A, NK 3 ATM Actual Value Range: 32~511
BTS590 over Default Value: None
0, Non-
BTS590 channeli
0 zed
WCDM STM-1/
A OC-3c
on
Iub/Iu/Iu
r
Interface
PATHID BSC690 ADD WRFD- Dynami Meaning: ID of one AAL2 path between two AAL2
0 AAL2P 0503010 c AAL2 nodes. The PATHID of the same AAL2 path
ATH 4 Connect configured between two AAL2 nodes must be the
BLK WRFD- ions in same. The value should not be equal to 0.
AAL2P 050404 Iub/ GUI Value Range: 1~4294967295
ATH IuCS/Iur
WRFD- Interface Unit: None
MOD 0213050 Actual Value Range: 1~4294967295
1 ATM/IP
AAL2P
Dual Default Value: None
ATH
Stack
RMV Node B
AAL2P
Dedicate
ATH
d Iub
UBL Transmi
AAL2P ssion
ATH Control
PATHID BSC691 ADD WRFD- Dynami Meaning: ID of one AAL2 path between two AAL2
0 AAL2P 0503010 c AAL2 nodes. The PATHID of the same AAL2 path
ATH 4 Connect configured between two AAL2 nodes must be the
BLK WRFD- ions in same. The value should not be equal to 0.
AAL2P 050404 Iub/ GUI Value Range: 1~4294967295
ATH IuCS/Iur
WRFD- Interface Unit: None
MOD 0213050 Actual Value Range: 1~4294967295
1 ATM/IP
AAL2P
Dual Default Value: None
ATH
Stack
RMV Node B
AAL2P
Dedicate
ATH
d Iub
UBL Transmi
AAL2P ssion
ATH Control
TXTRF BSC690 ADD WRFD- Overboo Meaning: TX traffic record index of the AAL2 Path
X 0 AAL2P 050405 king on on the out RNC port (ATM layer PVC traffic). The
ATH WRFD- ATM traffic index is configured in the ATM traffic table
MOD 050406 Transmi (see "LST ATMTRF").
AAL2P ssion GUI Value Range: 100~1999
WRFD-
ATH 0213050 ATM Unit: None
1 QoS
Introduc Actual Value Range: 100~1999
WRFD- tion on Default Value: None
0503010 Hub
4 Node B
WRFD- (Overbo
0503010 oking on
6 Hub
WRFD- Node B
0503010 Transmi
7 ssion)
Dedicate
d Iub
Transmi
ssion
Control
Dynami
c AAL2
Connect
ions in
Iub/
IuCS/Iur
Interface
Call
Admissi
on
Based
on Used
AAL2
Path
Bandwi
dth
CBR, rt-
VBR,
nrt-
VBR,
UBR
ATM
QoS
Classes
TXTRF BSC691 ADD WRFD- Overboo Meaning: TX traffic record index of the AAL2 Path
X 0 AAL2P 050405 king on on the out RNC port (ATM layer PVC traffic). The
ATH WRFD- ATM traffic index is configured in the ATM traffic table
MOD 050406 Transmi (see "LST ATMTRF").
AAL2P ssion GUI Value Range: 100~1999
WRFD-
ATH 0213050 ATM Unit: None
1 QoS
Introduc Actual Value Range: 100~1999
WRFD- tion on Default Value: None
0503010 Hub
4 Node B
WRFD- (Overbo
0503010 oking on
6 Hub
WRFD- Node B
0503010 Transmi
7 ssion)
Dedicate
d Iub
Transmi
ssion
Control
Dynami
c AAL2
Connect
ions in
Iub/
IuCS/Iur
Interface
Call
Admissi
on
Based
on Used
AAL2
Path
Bandwi
dth
CBR, rt-
VBR,
nrt-
VBR,
UBR
ATM
QoS
Classes
RXTRF BSC690 ADD WRFD- Overboo Meaning: RX traffic record index of the AAL2 Path
X 0 AAL2P 050405 king on on the out RNC port (ATM layer PVC traffic). The
ATH WRFD- ATM traffic index is configured in the ATM traffic table
MOD 050406 Transmi (see "LST ATMTRF").
AAL2P ssion GUI Value Range: 100~1999
WRFD-
ATH 0213050 ATM Unit: None
1 QoS
Introduc Actual Value Range: 100~1999
WRFD- tion on Default Value: None
0503010 Hub
4 Node B
WRFD- (Overbo
0503010 oking on
6 Hub
WRFD- Node B
0503010 Transmi
7 ssion)
Dedicate
d Iub
Transmi
ssion
Control
Dynami
c AAL2
Connect
ions in
Iub/
IuCS/Iur
Interface
Call
Admissi
on
Based
on Used
AAL2
Path
Bandwi
dth
CBR, rt-
VBR,
nrt-
VBR,
UBR
ATM
QoS
Classes
RXTRF BSC691 ADD WRFD- Overboo Meaning: RX traffic record index of the AAL2 Path
X 0 AAL2P 050405 king on on the out RNC port (ATM layer PVC traffic). The
ATH WRFD- ATM traffic index is configured in the ATM traffic table
MOD 050406 Transmi (see "LST ATMTRF").
AAL2P ssion GUI Value Range: 100~1999
WRFD-
ATH 0213050 ATM Unit: None
1 QoS
Introduc Actual Value Range: 100~1999
WRFD- tion on Default Value: None
0503010 Hub
4 Node B
WRFD- (Overbo
0503010 oking on
6 Hub
WRFD- Node B
0503010 Transmi
7 ssion)
Dedicate
d Iub
Transmi
ssion
Control
Dynami
c AAL2
Connect
ions in
Iub/
IuCS/Iur
Interface
Call
Admissi
on
Based
on Used
AAL2
Path
Bandwi
dth
CBR, rt-
VBR,
nrt-
VBR,
UBR
ATM
QoS
Classes
VPI BSC690 ADD WRFD- Dedicate Meaning: VPI of the AAL2 path out RNC. When the
0 AAL2P 0213050 d Iub AAL2 path is carried on the UOIa, AOUa, AEUa, or
ATH 1 Transmi AOUc board, the value for Bearing VPI ranges from 0
MOD WRFD- ssion to 255. When the AAL2 path is carried on the UOIc
AAL2P 0503010 Control board, the value for Bearing VPI ranges from 0 to 255
ATH 4 Dynami if WORKTYPE in the "SET OPT" command is set to
c AAL2 "UNI"; the value for Bearing VPI ranges from 0 to
WRFD- 4095 if WORKTYPE in the "SET OPT" command is
050301 Connect
ions in set to "NNI".
WRFD- Iub/ GUI Value Range: 0~4095
0503010 IuCS/Iur
6 Unit: None
Interface
Actual Value Range: 0~4095
ATM
Transmi Default Value: None
ssion
Introduc
tion
Package
Call
Admissi
on
Based
on Used
AAL2
Path
Bandwi
dth
VPI BSC691 ADD WRFD- Dedicate Meaning: VPI of the AAL2 path out RNC. When the
0 AAL2P 0213050 d Iub AAL2 path is carried on the AOUc board, the value
ATH 1 Transmi for Bearing VPI ranges from 0 to 255. When the
MOD WRFD- ssion AAL2 path is carried on the UOIc board, the value for
AAL2P 0503010 Control Bearing VPI ranges from 0 to 255 if WORKTYPE in
ATH 4 Dynami the "SET OPT" command is set to "UNI"; the value
c AAL2 for Bearing VPI ranges from 0 to 4095 if
WRFD- WORKTYPE in the "SET OPT" command is set to
050301 Connect
ions in "NNI".
WRFD- Iub/ GUI Value Range: 0~4095
0503010 IuCS/Iur
6 Unit: None
Interface
Actual Value Range: 0~4095
ATM
Transmi Default Value: None
ssion
Introduc
tion
Package
Call
Admissi
on
Based
on Used
AAL2
Path
Bandwi
dth
VCI BSC690 ADD WRFD- Dedicate Meaning: VCI of the AAL2 path out RNC.
0 AAL2P 0213050 d Iub GUI Value Range: 32~65535
ATH 1 Transmi
ssion Unit: None
MOD WRFD-
AAL2P 050404 Control Actual Value Range: 32~65535
ATH WRFD- ATM/IP Default Value: None
050301 Dual
Stack
Node B
ATM
Transmi
ssion
Introduc
tion
Package
VCI BSC691 ADD WRFD- Dedicate Meaning: VCI of the AAL2 path out RNC.
0 AAL2P 0213050 d Iub GUI Value Range: 32~65535
ATH 1 Transmi
ssion Unit: None
MOD WRFD-
AAL2P 050404 Control Actual Value Range: 32~65535
ATH WRFD- ATM/IP Default Value: None
050301 Dual
Stack
Node B
ATM
Transmi
ssion
Introduc
tion
Package
SIGLKS BSC690 ACT WRFD- ATM Meaning: Uniquely identifies a signaling link set.
X 0 MTP3L 050301 Transmi MTP3 signaling link sets are uniquely but not
NK ssion necessarily consecutively numbered within a RNC by
ADD Introduc using the signaling link set index. For example, you
MTP3L tion can set the number of an MTP3 signaling link set
NK Package towards a neighboring MGW to 10 and the number of
an MTP3 signaling link set towards another
DEA neighboring MGW to 12.
MTP3L
NK GUI Value Range: 0~186
INH Unit: None
MTP3L Actual Value Range: 0~186
NK Default Value: None
MOD
MTP3L
NK
RMV
MTP3L
NK
UIN
MTP3L
NK
SIGLKS BSC691 ACT WRFD- ATM Meaning: Uniquely identifies a signaling link set.
X 0 MTP3L 050301 Transmi MTP3 signaling link sets are uniquely but not
NK ssion necessarily consecutively numbered within a RNC by
ADD Introduc using the signaling link set index. For example, you
MTP3L tion can set the number of an MTP3 signaling link set
NK Package towards a neighboring MGW to 10 and the number of
an MTP3 signaling link set towards another
DEA neighboring MGW to 12.
MTP3L
NK GUI Value Range: 0~427
INH Unit: None
MTP3L Actual Value Range: 0~427
NK Default Value: None
MOD
MTP3L
NK
RMV
MTP3L
NK
UIN
MTP3L
NK
PEERT BSC690 ADD WRFD- Permane Meaning: IPoA PVC peer type
0 IPOAP 0503010 nt GUI Value Range: IUB, IUPS, OTHER
VC 5 AAL5
Connect Unit: None
WRFD-
050301 ions for Actual Value Range: IUB, IUPS, OTHER
Control Default Value: None
Plane
Traffic
ATM
Transmi
ssion
Introduc
tion
Package
PEERT BSC691 ADD WRFD- Permane Meaning: IPoA PVC peer type.
0 IPOAP 0503010 nt GUI Value Range: IUB, OTHER
VC 5 AAL5
Connect Unit: None
WRFD-
050301 ions for Actual Value Range: IUB, OTHER
Control Default Value: None
Plane
Traffic
ATM
Transmi
ssion
Introduc
tion
Package
CARRY BSC690 ADD WRFD- ATM Meaning: VPI value of the VCL of the bearer network
VPI 0 IPOAP 050105 Switchin GUI Value Range: 0~4095
VC WRFD- g Based
Hub Unit: None
MOD 031100
IPOAP Node B Actual Value Range: 0~4095
WRFD-
VC 0503010 BOOTP Default Value: None
5 Permane
WRFD- nt
050301 AAL5
Connect
ions for
Control
Plane
Traffic
ATM
Transmi
ssion
Introduc
tion
Package
CARRY BSC691 ADD WRFD- ATM Meaning: VPI value of the VCL of the bearer network
VPI 0 IPOAP 050105 Switchin GUI Value Range: 0~4095
VC WRFD- g Based
Hub Unit: None
MOD 031100
IPOAP Node B Actual Value Range: 0~4095
WRFD-
VC 0503010 BOOTP Default Value: None
5 Permane
WRFD- nt
050301 AAL5
Connect
ions for
Control
Plane
Traffic
ATM
Transmi
ssion
Introduc
tion
Package
CARRY BSC690 ADD WRFD- ATM Meaning: VCI value of the VCL of the bearer network
VCI 0 IPOAP 050105 Switchin GUI Value Range: 32~65535
VC WRFD- g Based
Hub Unit: None
MOD 031100
IPOAP Node B Actual Value Range: 32~65535
WRFD-
VC 0503010 BOOTP Default Value: None
5 Permane
WRFD- nt
050301 AAL5
Connect
ions for
Control
Plane
Traffic
ATM
Transmi
ssion
Introduc
tion
Package
CARRY BSC691 ADD WRFD- ATM Meaning: VCI value of the VCL of the bearer network
VCI 0 IPOAP 050105 Switchin GUI Value Range: 32~65535
VC WRFD- g Based
Hub Unit: None
MOD 031100
IPOAP Node B Actual Value Range: 32~65535
WRFD-
VC 0503010 BOOTP Default Value: None
5 Permane
WRFD- nt
050301 AAL5
Connect
ions for
Control
Plane
Traffic
ATM
Transmi
ssion
Introduc
tion
Package
8 Counters
9 Glossary
For the acronyms, abbreviations, terms, and definitions, see the Glossary.
10 Reference Documents