Professional Documents
Culture Documents
User Instruction Manual For Rescue/Personnel Riding System Rollgliss R350
User Instruction Manual For Rescue/Personnel Riding System Rollgliss R350
Rescue/Personnel Riding
System Rollgliss R350
This manual is intended to meet the
Manufacturer's Instructions as required by
the standards and should be used as part
of an employee training program as
required by OSHA
Side Side
DBI/SALA Plate Plate
Label (front) (rear)
Overroll
Guide
Stationary
Pulley Rope Guide
(3:1) (right)
load side
Rope ID/Warning
Label
Rope
Rope Thimble
System
System
Label
Label
Carabiner
Traveling
Pulley
(3:1)
3
Figure 2 - Parts Identification Continued
Connecting
Sling
Securing Strap
Connecting
Label
Securing Strap
Label
Rope Control
Device Inspection
Log
Label
4
DESCRIPTIONS
8902004: 3:1 ratio, 50 ft. distance (200 ft. 3/8-in. rope), interchangeable
pulley system. Includes R350 rope unit, rope control device, securing strap,
anchoring sling, 4 carabiners and bag.
8902006: 8902004 with 100 ft. travel distance (400 ft. 3/8-in. rope)
8092008: 8902004 with fixed pulleys
Typical models, ratios and ropes lengths listed. Additional models are available.
1.0 APPLICATIONS
B. RESCUE/RETRIEVAL
SYSTEM APPLICATION: In
this application, the Rollgliss
R350 is used as part of a
complete rescue system to
rescue individuals from heights
and depths or provide
protection/rescue to persons
trapped in confined spaces
(shafts, tanks, chimneys, etc.)
Such systems typically include
5
a full body harness or rescue Figure 4 - Emergency Operation
sling, anchorage connector (i.e.
carabiner, etc.) and the Rollgliss
R350. See Figure 4.
7
Figure 5 - Unintentional Disengagement (Roll-out)
If the connecting element that a snap hook (shown) or carabiner attaches to is
undersized or irregular in shape, a situation could occur where the connecting
element applies a force to the gate of the snap hook or carabiner. This force may
cause the gate (of either a self-locking or a non-locking snap hook) to open,
allowing the snap hook or carabiner to disengage from the connecting point.
Small ring or other
non-compatibly
shaped element
8
Figure 6 - Inappropriate Connections
D. To each other.
WARNING: Consult your doctor if there is any reason to doubt your fitness to
safely absorb the shock from a fall arrest or suspension. Age and fitness
seriously affect a worker's ability to withstand falls. Pregnant women or
minors must not use DBI/SALA rescue or personnel riding systems unless in
an emergency situation.
9
3.1 BEFORE EACH USE: Before each use of this or any rescue or
personnel riding system equipment, carefully inspect it to assure that
it is in serviceable condition. Check for worn or damaged parts.
Ensure all screws are present and secure. Inspect the rope for cuts,
fraying, burns, etc. Refer to section 5.0 for further inspection details.
Do not use if inspection reveals an unsafe condition.
3.2 PLANNING: Plan your rescue or personnel riding system and how it
will be used before starting your work. Take into consideration factors
that affect your safety before, during, and after a fall. The following list
gives some important points to consider when planning your system:
IMPORTANT: The load being raised, lowered or suspended from the system
should be located directly below the anchor point to prevent rope wear on the
pulleys.
IMPORTANT: The use of body belts for rescue or personnel riding is not
recommended. Body belts increase the risk of injury during a fall arrest in
comparison to a full body harness. Limited suspension time and the potential
for improperly wearing a body belt may result in added danger to the user's
health.
11
Figure 8 - Anchoring
Connection Sling
Connection Hook
Suitable (3620001)
(2000523)
anchorage
Using sling
Using connection connected
hook through eye. through eye.
12
Figure 9 - Pulleys
Stationary
Pulley
Stationary
8900183
Pulley
8900177
Traveling
Pulley
Traveling
8900179
Pulley
8900185
Stationary
Stationary Pulley
Pulley 8900193
8900187
Traveling
Pulley Traveling
8900189 Pulley
8900195
13
Table 1 - Recommended Ratio
Number of people Ratio Working Example
load
1 Individual descending 1:1 60 - 310 lbs. Lowering one person down incline
for rescue or work positioning.
1 Individual ascending 3:1, maximum Lifting and lowering one person for
and descending 4:1, 310 lbs. personal riding, work positioning
5:1 or rescue in confined
space/general work area.
*Lifting two people in emergency rescue or life threatening situations should be limited to
6 ft. or less, if possible, when a 3:1 or 4:1 ratio is used
Traveling
Pulley
14
Figure 11
Locking
Bolt
Fixed
Bolt
Figure 12
E. The locking bolt should also be loosened by
simultaneously depressing the front and
rear pin, and pushing to the right against the
spring (Figure 12).
Figure 13
G. To ensure the pulley is locked in position,
apply pressure to the pulley by pushing the
pulley side to side (Figure 13).
15
3.7 CONNECTING TRAVELING PULLEYS: The following policy applies in
respect to the pulley variations as shown in Figure 9 and section 3.5.
B. Bring the supporting face plates together, then snap on and lock
the carabiners through the holes provided (Figure 15).
3.8 OPERATION:
16
C. Attach one end of the web securing strap to the user and one end
to the rope control device by choking it off. Adjust the length of
the web securing strap (8901000) to keep the rope control device
within the user’s reach. Attach an
appropriate body support to the Figure 17
eye of the traveling pulley with a
Web
carabiner. Carefully allow the Securing
user’s body weight to be Strap
supported by the system. See Web choked
Figure 17. Securing off to
Strap rope
D. To raise, pull down on the rope control
control device. Hold the free end device.
of the rope with one hand and
slide the rope control device back
up the rope. Pull down on the rope
control device to further raise. Web
Repeat this procedure until the Securing
proper location is reached. See Strap
Figure 18. attached
to user.
E. To lower, grip the free end of the
rope with one hand and maintain
tension. Pull open the spring
loaded jaw and slowly allow the
rope to pass through the rope
control device. Protective hand
wear may be required to prevent
hand injury. Always maintain a
safe speed. See Figure 18.
Figure 18 - Raising and Lowering
17
WARNING: If rope tension eases during lowering, the person being lowered
may have reached a work level or obstruction. Do not continue operation
without communicating with the person being lowered. Always maintain
tension on the personnel line. Slack line could cause a free fall situation.
After passing the rope through the rope control device, route it
alternately over and under the pins on the braking aid. See Figures
19 and 20.
Figure 19 Figure 20
Rope configuration for medium Rope configuration for high
breaking force. breaking force.
4.0 TRAINING
4.1 It is the responsibility of the user to assure they are familiar with these
instructions, and are trained in the correct care and use of this
equipment. User must also be aware of the operating characteristics,
application limits, and the consequences of improper use of this
equipment.
18
5.0 INSPECTION
5.1 FREQUENCY:
• Before Each Use: Visually inspect per steps listed in sections 5.2
and 5.3.
Step 2. Inspect the side plates for distortion, cracks or other damage.
Step 3. Inspect the rope for cuts, severe abrasion, or wear. Check for
contact with acids or other chemicals.
Step 4. Inspect to make sure that the rope lies correctly in the pulley.
Step 5. Inspect the contact surface of the drum for any sign of wear
or strain. Check for distortion in the top loop.
Step 7. With the unit properly mounted from any sturdy structure, test
the functional load.
19
A. Make sure that the rope Figure 21
drum locks in the
clockwise direction Counterclockwise Clockwise
(reverse lock operative) drum rotates. drum stationary.
see Figure 21.
Step 1. Inspect that the pulleys are clean and free from grease.
Step 2. Inspect the contact surface of the pulleys for any sign of wear
or strain. Check for distortion in connecting loops.
Step 4. Make sure that the pulley can be rotated freely and without
resistance.
20
6.0 MAINTENANCE - SERVICING - STORAGE
6.1 Periodically clean the exterior of the Rollgliss R350 with a soft damp
cloth without using solvents, acids or alkaline solutions.
6.2 Clean the rope with water and mild soap detergent solution. Rinse and
thoroughly air dry. Do not force dry with heat. Immediately wash
entire rope assembly if it has been exposed to acidic vapors.
WARNING: If the rope comes in contact with liquid or solid acids, remove it
from service and wash with a water and mild detergent solution. Do not
return the system to service without first being inspected by a qualified
inspector. Acids in contact with rope for extended periods of time can weaken
rope without visible evidence of damage. Only a qualified inspector can
determine rope status.
6.4 Clean and store the body support and associated system components
according to separate instructions provided with that equipment.
6.5 Store your Rollgliss R350 in cool, dry, and clean environment out of
direct sunlight. Avoid areas where chemical vapors may exist. Inspect
the Rollgliss R350 after any period of extended storage.
7.0 SPECIFICATIONS
ROLLGLISS BLOCK:
Side Plates: 11ga. Stainless Steel, USN S30400
Drum: Aluminum, ALTEF coated
Shaft/Axle: Aluminum, T6
Rope Guide: Aluminum, ALTEF coated
Protective edge cap: Luran, plastic
PULLEYS:
Side Plates: 11ga. Stainless Steel, USN S30400
Pulley Wheel: Aluminum, ALTEF coated
Shaft: Aluminum Alloy
21
ROPE CONTROL DEVICE:
BODY: Aluminum, painted
JAW: Aluminum
STOP: Plastic
CARABINERS:
8900238
Material: Aluminum Alloy, 5,000 lbs. tensile strength
Finish: Polished
2000523
Material: High Tensile Alloy Steel, 5,000 lbs. tensile strength
Finish: Zinc Plated
SECURING STRAP:
Webbing; Polyester and Nylon
Buckle: Zinc Plated, adjustable
Thread: #346 polyester, #69 nylon
ANCHORING SLING:
Webbing: Polyester and Nylon
Thread: #346 polyester, #69 nylon
ROPE SYSTEM:
Rope:
3/8-in. polyamide, 5,300 lbs. breaking strength, white with red tracer
1/2-in. static kernmantle- meets NFPA 1983, 10,000 lbs. breaking
strength, red with white tracer
Thimble: Plastic
CARRYING BAG:
Material: 18-oz. vinyl coated polyester
22
8.0 LABELING
8.1 These labels should be securely attached to the Rollgliss R350. See
Figures 1 and 2.
ID/Warning Label
Inspection
Log Label
on Securing Rope System
Strap Label
23
DBI/SALA Logo Label
24
9.0 INSPECTION AND MAINTENANCE LOG
Approved By:
Approved By:
Approved By:
Approved By:
Approved By:
Approved By:
Approved By:
Approved By:
Approved By:
Approved By:
Approved By:
Approved By:
25
9.0 INSPECTION AND MAINTENANCE LOG
Approved By:
Approved By:
Approved By:
Approved By:
Approved By:
Approved By:
Approved By:
Approved By:
Approved By:
Approved By:
Approved By:
Approved By:
26
WARRANTY
USA Canada
3965 Pepin Avenue 260 Export Boulevard
Red Wing, MN 55066-1837 Mississauga, Ontario L5S 1Y9
Toll Free: 800-328-6146 Toll Free: 800-387-7484
Phone: (651) 388-8282 Phone: (905) 795-9333
Fax: (651) 388-5065 Fax: (905) 795-8777
www.salagroup.com www.salagroup.com
I S O
9001 Form: 5902125
Certificate No. FM 39709 Rev: A