Professional Documents
Culture Documents
Reference code
Design office FOR ANCHOR BOLT CAPACITY ONLY
Person in charge
Construction Office
Person in charge
= Slotted
Profile
Selected Profile RECT. HOLLOW 100x150x5
Eccentricity X: 0.0 mm
Y: 0.0 mm
Profile rotation 0.0°
DESIGN CONCRETE
08/08/2019 Page: 1 / 9
v. 4.0.3.454 - Database engine 216.30.2316085211
Project
Reference code
Design office
Person in charge
Construction Office
Person in charge
Selected Products
Anchor (name) MIT600RE, Steel 8.8
Approval ETA-09/0340
Size M20
Article code
Anchor data
d Anchor/thread diameter: 20.0 mm tfix Thickness of fixture: 16.0 mm
dnom Outside diameter of anchor: 20.0 mm SW Spanner: 0.0 mm
d0 Drill hole diameter: 24.0 mm Tinst Max setting torque 120.0 Nm
h1 Depth of drilled hole: 175.0 mm Use category, concrete Dry/Wet Bore Hole
hnom Setting depth: 170.0 mm
hef Effective anchorage depth: 170.0 mm Minimum stud lenght L 209.0 mm
df Diameter of clearance hole in fixture: 22.0 mm
PRODUCT
MIT600RE Pure Epoxy. European Technical Approval Option 1 for cracked and non-cracked concrete with anchor rod and with rebar
used as anchor. Fire resistance test certification F30-F120. VOC free according to Swiss legislation and certified A+ according to
DEVL 1101903D / DEVL 1104875A. LEED - Test Report. Certification for drinking water Systems. The anchor may also be used under
seismic influence for performance category C1 + C2. Application also in damp and water-filled drill holes. Indoor (zinc plated) and
outdoor (stainless steel) applications.
DESIGN CALCULATION
This calculation is based on specific values exclusively for the product above.
DESIGN CONCRETE
08/08/2019 Page: 2 / 9
v. 4.0.3.454 - Database engine 216.30.2316085211
Project
Reference code
Design office
Person in charge
Construction Office
Person in charge
Any changes to the brand or physical conditions for design will require a recalculation of the anchor design.
ANCHOR PLATE
The design program assumes, in accordance with EOTA TR029, that the anchor plate does not deform as a result of applied actions.
Thus, and in accordance with EOTA TR029, the anchor plate shall be sufficiently stiff and its design should be carried out according
to standards for steel structures ensuring elastic behaviour.
INSTALLATION
All conditions of the European Technical Approval (ETA) and Mungo technical publications shall be complied with in all detail.
The load values are valid only if the installation has been carried out correctly.
ATTENTION
The loads as well as the installation data can vary. Please consult our website www.mungo.swiss to download the newest version.
Input Data
Tension Bending Reinforcement
NSd,Z 0.00 kN MSd,X -11.70 kN·m Diameter 11 mm
Shear MSd,Y 0.00 kN·m Distance rebars 200 mm
VSd,X 0.00 kN Torsion Distance stirrups 200 mm
VSd,Y 9.70 kN MSd,Z 0.00 kN·m Edge reinforcement No
Edges
CXp ∞ mm
CXn ∞ mm
CYp ∞ mm
CYn ∞ mm
DESIGN CONCRETE
08/08/2019 Page: 3 / 9
v. 4.0.3.454 - Database engine 216.30.2316085211
Project
Reference code
Design office
Person in charge
Construction Office
Person in charge
Tension force Shear force Shear force (x) Shear force (y)
Anchor
[kN] [kN] [kN] [kN]
1 0.00 2.42 0.00 2.42
2 0.00 2.42 0.00 2.42
3 25.99 2.42 0.00 2.42
4 25.99 2.42 0.00 2.42
2 0.00 0.0%
3 25.99 19.9%
4 25.99 19.9%
DESIGN CONCRETE
08/08/2019 Page: 4 / 9
v. 4.0.3.454 - Database engine 216.30.2316085211
Project
Reference code
Design office
Person in charge
Construction Office
Person in charge
Group N0R,kp Ac,N A0c,n ψs,Np hef scr,Np ccr,Np c-x c+x c-y c+y
Anchor
No. [kN] [mm²] [mm²] [-] [mm] [mm] [mm] [mm] [mm] [mm] [mm]
1 [3, 4] 65.37 336,600 260,100 1.000 170 510 255 6,000 6,000 6,000 6,200
Group sm ψg,Np ψre,Np eNp,x eNp,y ψec,Np NRk,p NRd,p NSd βNp
Anchor
No. [mm] [-] [-] [mm] [mm] [-] [kN] [kN] [kN] [%]
1 [3, 4] 150.0 1.071 1.000 0.0 0.0 1.000 90.62 43.15 51.98 120.4%
Group N0Rk,c Ac,N A0c,N hef scr,N ccr,N c-x c+x c-y c+y
Anchor
No. [kN] [mm²] [mm²] [mm] [mm] [mm] [mm] [mm] [mm] [mm]
1 [3, 4] 87.41 336,600 260,100 170 510 255 6,000 6,000 6,000 6,200
Group ψs,N ψre,N eN,x eN,y ψec,N NRk,c NRd,c Nsd βN,c
Anchor
No. [-] [-] [mm] [mm] [-] [kN] [kN] [kN] [%]
1 [3, 4] 1.000 1.000 0.0 0.0 1.000 113.12 53.87 51.98 96.5%
As the calculation is performed for cracked concrete, no proof for splitting failure is required.
DESIGN CONCRETE
08/08/2019 Page: 5 / 9
v. 4.0.3.454 - Database engine 216.30.2316085211
Project
Reference code
Design office
Person in charge
Construction Office
Person in charge
1 2 3 4
l αm M0R,ks
[ mm ] [-] [ Nm ]
1 2 3 4
VRk,cp=k · NRk,c
Group N0Rk,c Ac,N A0c,N ψs,N ψre,N c-x c+x c-y c+y
Anchor
No. [kN] [mm2] [mm2] [-] [-] [mm] [mm] [mm] [mm]
DESIGN CONCRETE
08/08/2019 Page: 6 / 9
v. 4.0.3.454 - Database engine 216.30.2316085211
Project
Reference code
Design office
Person in charge
Construction Office
Person in charge
1 [1, 2, 3, 4] 87.41 468,600 260,100 1.000 1.000 6,000 6,000 6,000 6,000
VRk,cp=k · NRk,p
1 [1, 2, 3, 4] 65.37 468,600 260,100 175.0 1.156 6,000 6,000 6,000 6,000
Group ψs,N ψre,N en,x en,y ψec,N NRk,c VRk,cp VRd,cp VSd βV,cp
Anchor
No. [-] [-] [mm] [mm] [-] [kN] [kN] [kN] [kN] [%]
[1, 2, 3,
1 1.000 1.000 0.0 0.0 1.000 136.09 272.18 181.46 9.70 5.3%
4]
As all edges are greater than 10 hef and 60 d, the proof for concrete edge failure is omitted.
DESIGN CONCRETE
08/08/2019 Page: 7 / 9
v. 4.0.3.454 - Database engine 216.30.2316085211
Project
Reference code
Design office
Person in charge
Construction Office
Person in charge
Anchor
βN,s βN,p βN,comb βN,c βN,sp βV,s βV,sla βV,cp βV,c βN,s,max βV,s.max βN,c,max, βV,c,max,E βcombi,c,E βcombi,S,E
E
1 0.0% 0.0% 0.0% 0.0% 0.0% 3.1% 11.1% 5.3% 0.0% 0.0% 11.1% 0.0% 5.3% 1.2% 1.2%
2 0.0% 0.0% 0.0% 0.0% 0.0% 3.1% 11.1% 5.3% 0.0% 0.0% 11.1% 0.0% 5.3% 1.2% 1.2%
3 19.9% 0.0% 120.4% 96.5% 0.0% 3.1% 13.9% 5.3% 0.0% 19.9% 13.9% 120.4% 5.3% 104.8% 5.9%
4 19.9% 0.0% 120.4% 96.5% 0.0% 3.1% 13.9% 5.3% 0.0% 19.9% 13.9% 120.4% 5.3% 104.8% 5.9%
βN,s,max = βN,s
βV,s,max = max ( βV,s , βV,sla )
With consideration of related anchors and separation of steel and concrete failure
RESULT
Anchor(s) is rejected as the decisive utilization exceeds the allowed capacity
REMARKS
The verification of anchor design cases covered by ETAG 001 or TR29 is performed according to the selected Guideline. The
verification of anchor design cases non-covered by guidelines is based on the selected Guideline. Further information can be
found inside ACP Design Guides. The loads acting on anchors are evaluated according to the theory of elasticity, assuming
that the anchor plate does not deform under the design actions. To ensure the validity of this assumption the anchor plate
shall be sufficient stiff. The user must verify this condition, since the base plate stiffness is not automatically calculated by the
software. The transfer of loads from anchors into base material must be verified in accordance with ETAG 001 Annex C or
TR29 Section 7. The design method is valid only for clearance hole in the fixture with a diameter not larger than the values
given in ETAG 001 Annex C or TR29 Table 4.1.
IMPORTANT NOTICE
The data input to this software, and the relative results, must be checked by the user under the responsibility of an engineer
experienced in anchorages and concrete work. This is to ensure there are no errors and all data is complete and accurate and
complies with all rules and regulations for the actual conditions and application.
The data contained in this software relates only to the product illustrated therein and is based on principles, formulas and
safety regulations according to the existing guidelines for anchorages into concrete, together with the knowledge of the
manufacturer.
The user must comply with these principles. The user is solely responsible for the data entered into the program and any
errors or omissions are the responsibility of the user. The user must ensure that the most current version of the program is
DESIGN CONCRETE
08/08/2019 Page: 8 / 9
v. 4.0.3.454 - Database engine 216.30.2316085211
Project
Reference code
Design office
Person in charge
Construction Office
Person in charge
DESIGN CONCRETE
08/08/2019 Page: 9 / 9
v. 4.0.3.454 - Database engine 216.30.2316085211