The document summarizes the steps taken to perform a firmware update on a Siemens 7SJ8021 relay from version 04.74.05 to 04.77.03. This involved downloading the necessary device drivers and firmware update files from the Siemens website, connecting to the device to download settings, and performing the update without changing parameter sets as recommended. During the update process, communication errors were encountered but resolved by changing COM ports and device addresses. The updated firmware required modifying parameter sets in DIGSI software to finally enable successful communication with the relay.
Original Description:
Siemens protection relay firmware update - a practical sequence
The document summarizes the steps taken to perform a firmware update on a Siemens 7SJ8021 relay from version 04.74.05 to 04.77.03. This involved downloading the necessary device drivers and firmware update files from the Siemens website, connecting to the device to download settings, and performing the update without changing parameter sets as recommended. During the update process, communication errors were encountered but resolved by changing COM ports and device addresses. The updated firmware required modifying parameter sets in DIGSI software to finally enable successful communication with the relay.
The document summarizes the steps taken to perform a firmware update on a Siemens 7SJ8021 relay from version 04.74.05 to 04.77.03. This involved downloading the necessary device drivers and firmware update files from the Siemens website, connecting to the device to download settings, and performing the update without changing parameter sets as recommended. During the update process, communication errors were encountered but resolved by changing COM ports and device addresses. The updated firmware required modifying parameter sets in DIGSI software to finally enable successful communication with the relay.
Old Parameter set: 04.74.05 New Parameter Set: 04.77.03
STEPS:
1. Download Digsi Device driver from Siemens website and install in PC
7SJ80x_V047703_GerTreiDig0492_V01.00.00.exe 2. Download Firmware update from Siemens website and install in PC Setup_7SJ80x_04.77.03.EXE 3. Connect to Device & download settings via Plug & Play. Use selection USB instead of Direct during connection 4. Proceeded without Parameter set update as recommended in the manual If the firmware update changes the designation of the version only by the second number behind the decimal point, (e.g. from V4.02 to V4.03), then the existing parameter set does not need to be updated (for exception's see appendix table 1). In this case you may skip this chapter from now on and reload the stored parameter set into the device after the firmware update using DIGSI. 5. No need to open DIGSI for firmware update. 6. Start the Firmware update ICON created on the Desktop during Step 2. 7. Started update but error pops up, “COM1 NOT OPEN” In the same update window select PREFERENCE, select available ports COM5, COM6 etc 8. Updated in <3 minutes. 9. Confirmed communicating with default variant created during step.3 10. Insert new device with MLFB version in DISI and tried communicating. No communication 11. Found the device VD address in the MLFB version is different from default. Changed the MLFB version VD address with the default address. 12. Started communication with relay via DIGSI but ended with error Unable to combine settings Internal fault Unable to continue device processing 13. Under Object properties, found the following, New MLFB version – Parameter set: V4.77.03 Old Default version – Parameter set: V4.74.05 14. Keep a second copy of default variant. 15. With copy of default variant, right click and select “update parameter set” This updates the parameter set in DIGSI and not in device 16. From Default variant with updated parameter set connect by “DiGSI to DEVICE” After succesfull communication the Device P.SET is updated to new Version. 17. Now start communication with device again via created MLFB variant. Device to PC Finally successful 18. But still the DEVICE CONFIGURATION is in Disabled mode. But found enabled in offline mode, do changes in offline mode & send to relay. 19. FINISH.
iPad Pro 2021 (5th Generation) And iPhone 12 User Guide A Complete Step By Step Guide For Beginners, Seniors And Pro To Master New iPad 2021 & iPhone 12 Pro And Pro Max