Professional Documents
Culture Documents
Features
Sensors
(B)
● Various input/output (default: indicator) Fiber
Optic
- Input: DC voltage, DC current, AC voltage, AC current Sensors
(H)
Please read “Safety Considerations” in operation Temperature
Controllers
manual before using.
MT 4 W DV 4 N
(J)
N Indicator (without output function) Counters
0 Relay output
1 NPN open collector output (K)
MT4Y 2 PNP open collector output Timers
100-240VAC ※1
3 Relay (low out)+transmission (DC4-20mA) output
※1 (L)
4 Relay (low out)+RS485 communication output Panel
Meters
5 BCD dynamic output
6 Low speed serial output (M)
Output Tacho /
N Indication type (no output function) Speed / Pulse
Meters
12-24VDC,
0 Relay+transmission (DC4-20mA) output
100-240VAC (N)
1 Relay output Display
Units
2 NPN open collector+BCD dynamic output
3 PNP open collector+BCD dynamic output
MT4W (O)
4 NPN open collector+transmission (DC4-20mA) output Sensor
Controllers
5 PNP open collector+transmission (DC4-20mA) output
100-240VAC (P)
6 NPN open collector+low speed serial output Switching
Mode Power
7 PNP open collector+low speed serial output Supplies
8 NPN open collector+RS485 communication output
(Q)
9 PNP open collector+RS485 communication output Stepper Motors
& Drivers
※2 & Controllers
Power supply 1 12-24VDC
(R)
4 100-240VAC 50/60Hz Graphic/
Logic
DV DC voltage Panels
※1: Only lST(preset output mode) setting is available in MT4Y-☐-43 (relay (low out)+transmission (DC4-20mA) output) and
MT4Y-☐-43 (relay (low out)+transmission (DC4-20mA) output) models.
※2: Only for MT4W. ※To measure the current over DC5A, please select DV type because the shunt should be used.
※In case of selecting frequency display, no output will be provided even if it is output support models.
(main output, sub output and RS485 communication output)
L-35
MT4Y/MT4W Series
Specifications
MT4Y-DV-4 MT4Y-AV-4 MT4W-DV-4 MT4W-AV-4 MT4W-DV-1 MT4W-AV-1
Series
MT4Y-DA-4 MT4Y-AA-4 MT4W-DA-4 MT4W-AA-4 MT4W-DA-1 MT4W-AA-1
AC voltage, AC voltage, AC voltage,
DC voltage, DC voltage, DC voltage,
Measurement input current, current, current,
current current current
Frequency Frequency Frequency
Power supply 100-240VACᜠ 50/60Hz 12-24VDCᜡ
Allowable voltage range 90 to 110% 90 to 110%
Power consumption 5VA 5W
Display method 7-segment LED display (red) (character height: 14.2mm)
• 23℃±5℃ - DC Type: F.S. ±0.1% rdg±2-digit / AC Type: F.S. ±0.3% rdg±3-digit (frequency: F.S.±0.1% rdg±2-digit)
Display accuracy DC/AC Type: F.S +0.3% rdg ±3-digit max. only for 5A terminal
• -10℃ to 50℃ - DC/AC Type: F.S.±0.5% rdg±3-digit
Max. allowable input 110% F.S. for each measured input range
A/D conversion method Practical oversampling using successive approximation ADC
Sampling cycle DC type: 50ms, AC type: 16.6ms
Max. display range -1999 to 9999 (4-digit)
• Relay output - Contact capacity: 250VACᜠ 3A, 30VDCᜡ 3A / Contact composition: N.O (1a)
Preset output
• NPN/PNP Open collector output - Max. 12-24VDCᜡ ±2V 50mA (resistive load)
• RS485 communication output - Baud rate: 1,200/2,400/4,800/9,600, Communication method
Sub output : 2-wire half duplex, Synchronous method: Asynchronous method, Protocol: Modbus type
(transmission output) • Serial/BCD dynamic output - NPN Open collector output: 12-24VDC Max. 50mA (resistive load)
• DC4-20mA output - Resolution: 12,000 division (load resistance max. 600Ω), Response time: max. 450ms
AC measuring function※1 Selectable RMS or AVG
Frequency measurement function※1 Measurement range: 0.100 to 9999Hz (variable by decimal point position)
Hold function※2 Includes (external hold function)
Insulation resistance Over 100MΩ (at 500VDC megger, between external terminal and case)
Dielectric stength 2000VAC 50/60Hz for 1 min (between external terminal and case)
Noise immunity ±2kV the square wave noise (pulse width: 1㎲) by the noise simulator
Mechanical 0.75mm amplitude at frequency of 10 to 55Hz (for 1 min) in each X, Y, Z direction for 2 hours
Vibration
Malfunction 0.5mm amplitude at frequency of 10 to 55Hz (for 1 min) in each X, Y, Z direction for 10 min
Mechanical 100m/s² (approx. 10G) in each X, Y, Z direction for 3 times
Shock
Malfunction 300m/s² (approx. 30G) in each X, Y, Z direction for 3 times
Relay Malfunction Min. 20,000,000 operations
life cycle Mechanical Min. 100,000 operations (250VAC 3A load current)
Environ Ambient temperature -10 to 50℃, storage: -20 to 60℃
-ment Ambient humidity 35 to 85%RH, storage: 35 to 85%RH
Double insulation or reinforced insulation
Insulation type
(mark: , dielectric strength between the measuring input part and the power part: 1kV)
Approval
Weight※3 Approx. 213.5g (approx. 134g) Approx. 326g (approx. 211g)
※1: AC measuring function, and frequency measuring function are only for AC measuring input type.
※2: MT4Y- -4N model has no hold function.
※3: The weight includes packaging. The weight in parenthesis is for unit only.
※Environment resistance is rated at no freezing or condensation.
Unit Description
● MT4Y Series ● MT4W Series
1 1
2 6 2 6
3
3
4 5
4 5
L-36
Multi Panel Meter
Connections (A)
Photoelectric
Sensors
Measuring input connection of MT4Y Series
(B)
● MT4Y-DV-4 ● MT4Y-AV-4 Fiber
Optic
1 2 3 4 5 6 7 1 2 3 4 5 6 7 Sensors
(C)
250mV 2V/1V Door/Area
/50mV Sensors
5V/1V SOURCE 20V/10V SOURCE
100-240VAC 110V/50V 100-240VAC
50V/10V
50/60Hz 5VA 50/60Hz 5VA (D)
500V/100V 500V/250V Proximity
Sensors
● MT4Y-DA-4 ● MT4Y-AA-4
(E)
1 2 3 4 5 6 7 1 2 3 4 5 6 7 Pressure
Sensors
5mA 100mA
/2mA /50mA
(F)
50mA/ SOURCE 500mA SOURCE Rotary
4-20mA 100-240VAC /250mA 100-240VAC Encoders
500mA/200mA 50/60Hz 5VA 1A 50/60Hz 5VA
(G)
5A/2A 5A/2.5A Connectors/
Connector Cables/
Sensor Distribution
Output terminal of connection of MT4Y Series Boxes/Sockets
●MT4Y- -4N (indicator) ●MT4Y- -40 (triple relay output) ●MT4Y- -41 (H)
Temperature
Controllers
(triple NPN open collector output)
8 9 10 11 12 13
8 9 10 11 12 13 (I)
SSRs / Power
Hold/Zero Controllers
1 2 3 4 5 6 7 HI GO LO COM Hold/Zero
CONTACT OUT HI GO LO COM
(J)
Counters
: 250VAC 3A 1a, 30VDC 3A 1a RESISTIVE LOAD
●MT4Y- -42 ●MT4Y- -43 ●MT4Y- -44
(triple PNP open collector output) (relay+transmission (DC4-20mA) output) (relay+RS485 communication output) (K)
Timers
8 9 10 11 12 13 8 9 10 11 12 13 8 9 10 11 12 13
(L)
+ - B (-) A (+) Panel
Hold/Zero Hold/Zero Hold/Zero Meters
DC4-20mALoad OUT1 OUT1
600Ω max. RS485
HI GO LO COM CONTACT OUT CONTACT OUT (M)
: 250VAC 3A 1a, 30VDC 3A 1a : 250VAC 3A 1a, 30VDC 3A 1a Tacho /
RESISTIVE LOAD RESISTIVE LOAD Speed / Pulse
Meters
●MT4Y- -45 (BCD dynamic output) ●MT4Y- -46 (low speed serial output)
(N)
A C D0 D2 Dot
Hold/Zero
PCB 8 9 10 11 12 13 Display
Units
Hold/Zero
2 4 6 8 10 12 14 (O)
Sensor
CLOCK DATA LATCH POL COM Controllers
1 3 5 7 9 11 13 ※POL: W hen a display value is "-",
the signal of "-" will be outputted. (P)
COM B D D1 D3 POL Switching
※Hirose connector pin header model of the unit: HIF3BA-14PA-2.54DS Mode Power
※Contact Hirose Electric to purchase socket and wires of Hirose connector. Supplies
1 2 3 4 5 6 7 8 9 1 2 3 4 5 6 7 8 9
Panels
(S)
250mV Field
2V/1V
/50mV Network
+ - + - Devices
Hold/Zero 20V/10V Hold/Zero
5V/1V
50V/10V
SOURCE 110V/50V SOURCE
12-24VDC 5W 12-24VDC 5W (T)
500V/100V 500V/250V Software
COM 100-240VAC COM 100-240VAC
50/60Hz 5VA 50/60Hz 5VA
● MT4W-DA- ● MT4W-AA-
1 2 3 4 5 6 7 8 9 1 2 3 4 5 6 7 8 9
5mA 100mA
/2mA /50mA
+ - + -
50mA/ Hold/Zero 500mA Hold/Zero
4-20mA SOURCE /250mA SOURCE
500mA/200mA 12-24VDC 5W 1A 12-24VDC 5W
5A/2A
100-240VAC 5A/2.5A 100-240VAC
COM 50/60Hz 5VA COM 50/60Hz 5VA
L-37
MT4Y/MT4W Series
Output terminal connection of MT4W Series
● MT4W- - 0 (triple relay+transmission (DC4-20mA) output) ● MT4W- - 1 (triple relay output)
MAIN OUT MAIN OUT
CONTACT OUT CONTACT OUT
: 250VAC 3A 1a, 30VDC 3A 1a RESISTIVE LOAD : 250VAC 3A 1a, 30VDC 3A 1a RESISTIVE LOAD
10 11 12 13 14 15 10 11 12 13 14 15
+ -
DC4-20mA HI GO LO
HI GO LO COM Load 600Ω Max.
1 2 3 4 5 6 7 8 9 1 2 3 4 5 6 7 8 9
PCB
2 4 6 8 10 12 14 16 18 20 2 4 6 8
MAIN OUT: MAIN OUT:
NPN OPEN COLLECTOR PNP OPEN COLLECTOR
12-24VDC Max. 50mA 1 3 5 7 9 11 13 15 17 19 12-24VDC Max. 50mA 1 3 5 7
COM2 DATA
COM1 HI LO COM1 HI LO 0V
0V SERIAL OUT:
NPN OPEN COLLECTOR
12-24VDC Max. 50mA
L-38
Multi Panel Meter
(C)
● Panel cut-out Door/Area
Sensors
Min. 91
36
30
(D)
Proximity
31.5+ 00.5
Sensors
Min. 40
<MT4Y- -4N, 40 to 44, 46>
68
+ 0.7
(F)
Rotary
6 77 10 Pin Hirose connector Encoders
(HIF3BD-10PA-2.54DS) (G)
Connectors/
● MT4Y- -40, 41, 42 Connector Cables/
Sensor Distribution
30
Boxes/Sockets
(H)
Temperature
<MT4Y- -45> Controllers
(I)
SSRs / Power
Controllers
● MT4W- - N (indicator)
(J)
Counters
109 106 ● Panel cut-out
96 6 89.5 Relay contact
Min. 116
output terminal (K)
Timers
45 + 00.6
Min. 52
(L)
44.8
Panel
48
92 + 00.8 Meters
(M)
Tacho /
※There is no Relay output terminal block in Speed / Pulse
Meters
indication type.
(N)
< MT4W- - N, MT4W- - 0, 1> Display
● MT4W- - 0 to 9 Units
110.4
(O)
6 89.5 Sensor
20 Pin Hirose connector Controllers
(HIF3BA-20PA-2.54DS)
(P)
Switching
Mode Power
44.8
Supplies
(Q)
Stepper Motors
& Drivers
& Controllers
< MT4W- - 2 to 9>
(R)
Graphic/
Logic
Parameter Setting Panels
(S)
※Press MODE key in RUN mode and it enters PA 0 group. Field
RUN Network
※Press MODE key for over 3 sec in RUN mode, it displays [PA1]. Devices
3 sec ※Press MODE key for over 5 sec in RUN mode, it displays [PA2] after [PA1].
3 sec
When pressing MODE key continually, it stops displaying at [PA2]. (T)
Software
※It is advanced to current display parameter releasing MODE key at [PA1] or [PA2].
※Press MODE key for over 3 sec in any parameter groups, it returns to RUN
PA 0 PA1
mode.
2 sec ※If any key is not entered for 60 sec in each parameter, it returns to RUN mode.
※After returning to RUN mode, press MODE key within 2 sec, it returns to previous
PA2 parameter. (Refer to the below descriptions of each parameter group.)
※PA 0 group cannot be entered when preset output mode of [PA2] group is
3 sec
OFF.
L-39
MT4Y/MT4W Series
Parameter 1 Group
RUN
3 sec
DISP STND
- Refer to " Measurement Input".
(FREQ mode is only for AC measuring type.)
Max. display Decimal point Select decimal point position. Decimal point Set frequency measuring
STND value DOT position Setting range DOT position range, it is decided as
: 0, )0, )00, )000 the decimal point position.
※ When selecting the decimal ( change the
point position, "H-SC ", L-SC " have decimal point position)
It shows Max. display decimal point position.
value of standard 0 1 to 9999Hz
specification.
Set display value against )0 0.1 to 999.9Hz
Display value is fixed. Max. display
H-SC value max. measuring input. )00 0.10 to 99.99Hz
( : shift the digit )000 0.100 to 9.999Hz
: change setting value) ※In case of selecting frequency display, no
output will be provided even if it is output
support models (main output, Sub output
and RS485 communication output).
Set display value against
Min. display
L-SC value
min. measuring input.
It corrects a gradient of High-limit display value against max. input. It corrects a gradient of display
INbH !000 Setting range: )100 to %000 (%) INbH !000 value against max.input.
( : change setting value, : shift the digit) Setting range: 0.001 to 9.999
( : shift the digit,
: change setting value)
※After setting each mode, press MODE key for 2 sec to return to RUN.
※If any key is untouched for 60 sec after advance to parameter, it will return to RUN.
Factory defaults
Parameter MT4Y/W-DV MT4Y/W-DA MT4Y/W-AV MT4Y/W-AA Parameter MT4Y/W-DV MT4Y/W-DA MT4Y/W-AV MT4Y/W-AA
IN-R 500V SA 500V SA INbH !000 !000 !000 !000
DISP STND STND STND STND INbL 00 00 00 00
IN-T - - AVG AVG DOT )0 )000 )0 )000
STND 50)0 %000 50)0 %000 INbE - - 10-0 10-0
L-40
Multi Panel Meter
5 sec (B)
Fiber
PA2 Optic
Sensors
Move after 1 sec
(C)
Select preset output mode. (only for available models)
OUtT OFF Setting range: OFF, lST, hST, LhST, HhST, LlST, LdST
Door/Area
Sensors
※Only lST setting is available in MT4Y-☐-43 and MT4Y-☐-44 models.
(D)
Set preset hysteresis. The range is within 10% of max. display range (unit: digit). Proximity
HYS 001 ※ OUtT mode is OFF, it is not displayed. Sensors
(E)
Set startup compensation time. Pressure
STaT 0)0 ( : shift the digit, : change setting value)
Sensors
(G)
※If it is set to 00 sec [00 S], parameters of high-peak monitoring value [hPEK]/low-limit monitoring value [lPEK] in the Connectors/
parameter 0 group will be not displayed. Connector Cables/
Sensor Distribution
Set display cycle and also variable sets by 0.1 sec. ( : shift the digit, : change setting value) Boxes/Sockets
D1sT )2 5 Setting range: 0.1 to 5.0 sec (H)
Temperature
Controllers
Select zero function with operation at front. (set with key)
ZERO NO When + Key are pressed for 3 sec to set ㅛㄷㄴYES, it will be zero function and the deviation (I)
value is saved automatically at ㅛ INbL mode. SSRs / Power
Controllers
Select input with 6, 7 (MT4W)[12, 13 (MT4Y)] terminal or zero function for external signal.
EV1N HOLD (set with , Key)
(J)
HOLD: Holding display value, ZERO: Zero function using Hold/Zero terminal Counters
Set the high limit value, output point of current output 20mA.
FS-H 50)0 ( : shift the digit, : change setting value) (K)
(When changing measuring input and prescale mode, it is changed automatically Timers
as maximum value of input range.)
Set the low limit value, output point of current output 4mA.
FS-L 00)0 ( : shift the digit, : change setting value)
(L)
Panel
(When changing measuring input and prescale mode, it is changed automatically Meters
(O)
Set parity bit of RS485 communication. Sensor
PRTY NONE Setting range: NONE, EVEN, ODD
Controllers
(P)
Switching
Set stop bit of RS485 communication. Mode Power
STP 2 Setting range: 1, 2 Supplies
(Q)
Stepper Motors
& Drivers
Set response wait time of RS485 communication.
RSwT 5 Setting range: 5 to 99
& Controllers
(R)
OFF Disable to lock keys Graphic/
Logic
Set key lock function and select from 4 types. LOC1 Lock Parameter 1 Panels
LOC OFF Setting range: OFF, LOC1, LOC2, LOC3
LOC2 Lock Parameter 1, 2 (S)
Field
LOC3 Lock Parameter 0, 1 and 2 Network
Devices
※The dotted mode is only displayed for output type.
※After setting each mode, press MODE key for 2 sec to return to RUN mode. (T)
※If any key is untouched for 60 sec after advance to parameter, it will return to RUN mode. Software
Factory defaults
Parameter MT4Y/W-DV MT4Y/W-DA MT4Y/W-AV MT4Y/W-AA Parameter MT4Y/W-DV MT4Y/W-DA MT4Y/W-AV MT4Y/W-AA
OUtT OFF OFF OFF OFF EV1N HOLD HOLD HOLD HOLD
HYS 001 001 001 001 FS-H 50)0 %000 50)0 %000
STAT 0)0 0)0 0)0 0)0 FS-L 00)0 )000 00)0 )000
PEkT 00 5 00 5 00 5 00 5 ARDS 01 01 01 01
DIsT )2 5 )2 5 )2 5 )2 5 BPS 9600 9600 9600 9600
ZERO NO NO NO NO LOC OFF OFF OFF OFF
L-41
MT4Y/MT4W Series
Parameter 0 Group
RUN
※If any key is untouched for 60 sec after advance to parameter, it will return to RUN mode.
Factory defaults
Parameter MT4Y/W-DV MT4Y/W-DA MT4Y/W-AV MT4Y/W-AA Parameter MT4Y/W-DV MT4Y/W-DA MT4Y/W-AV MT4Y/W-AA
hSET 50)0 %000 50)0 %000 hPEK )0 )000 )0 )000
lSET 00)0 )000 00)0 )000 lPEK )0 )000 )0 )000
Measurement Input
Type Measuring input and range Input impedance Display range [STND] Prescale display range [SCAL]
L-42
Multi Panel Meter
(D)
Proximity
Sensors
(E)
Pressure
Sensors
(F)
Rotary
Encoders
Display Units (DS/DA-T Series)
(G)
DS/DA-T Series Connectors/
Connector Cables/
(RS485 communication input type display unit) Sensor Distribution
Boxes/Sockets
(H)
Temperature
Controllers
(I)
SSRs / Power
Controllers
DS16- T DS22/DA22- T DS40/DA40- T DS60/DA60- T
(J)
※Connect RS485 communication input type display unit (DS/DA-T Series) and RS485 communication output model of MT4Y/MT4W Series, Counters
the display unit displays present value of the device without PC/PLC.
(K)
Timers
Functions
(L)
AC frequency measurement
Panel
Input correction Front panel Meters
Operation Input external signal
[PA 1 group: DISP] value key
(M)
It measures input signal frequency when it is AC input. Tacho /
Speed / Pulse
PA 1: Direct Press , Short-circuit external
It uses fixed decimal point [PA1: DOT], measured range Meters
input correction key for 3 sec Hold terminal 11,12
can be changed by setting and measured range of decimal Description
value method at at the [6, 7 (MT4W)] over (N)
point position is as below chart. It is available to adjust the INbL. RUN mode. min. 50m.
Display
Units
upper gradient at [PA 1: INbH]and [PA 1: INbE]. In order to
measure frequency normally, input signal, over 10% F.S. of ※Refer to " Error correction", " Error display" and (O)
Sensor
the measured range, should be supplied. Please select the " Parameter 2 Group" for function and error. Controllers
proper point of
① Measuring range (P)
Transmission (DC4-20mA) output scale Switching
Mode Power
Decimal point
[PA2 group: ]
Supplies
position
0.000 0.00 0.0 0 /
(Q)
Measurement 0.100 to 0.10 to 0.1 to 1 to It sets transmission output for the display value at the Stepper Motors
range 9.999Hz 99.99Hz 999.9Hz 9999Hz output current DC4-20mA. & Drivers
& Controllers
※Accuracy of frequency measurement: It sets display value for 4mA at FS-L and 20mA at FS-H (R)
Below 1kHz, F.S. ±0.1rdg ±2-digit. and the range between FS-H and FS-L should be 10% Graphic/
Logic
From 1kHz to 10kHz, F.S. ±0.3rdg ±2-digit. ※When min. set interval between FS-H and FS-L is Panels
② INbH: 0.100 to 9.999 [Gradient adjustment of high value] set as under 10% F.S., it changed as over 10% F.S. (S)
-2 -1 0 1
③ INbE: 10 , 10 , 10 , 10 [Index adjustment of INbH] automatically. Field
Network
※Preset display value is fixed to output as 4mA at under Devices
20mA
display value]
It adjusts the display value of the optional configured input
value as zero by force, zero point error can be adjusted
with 3 ways as below. When zero point adjustment with Min.
4mA setting range
front key and Hold terminal is finished normally, zero point F.S. 10%
of measurement terminal is displayed and the adjusted FS-L FS-H
Display value
value at saved in INbL automatically.
L-43
MT4Y/MT4W Series
Initialization Gradient correction [PA 1 group: INbH]
It initializes as the factory default status. If press , , This function is to correct a gradient of prescale value and
keys together for 2 sec in RUN mode, INlT mode and the display value. (Fig.1) Display value Y can be used as α, β
setting value (NO) is displayed every 0.5 sec and it will be times against X input value by correction function [INbH].
initialized as the factory default when press MODE key after And also can be used as correction function of max.
change NO→ YES. display value (H-SC). Adjustment range is 0.100 to 5.000
and multiply current gradient.
E.g.) Input: DC200mV, Display: 3.000 for MT4W-DV
Startup compensation time
[PA 2 group: STAT] Display value for
This time function limits the operation of an output until the measuring input
measured input (overvoltage or inrush current) is stable αY 15.000
at moment of power on. All outputs are off during startup α time 12.000
Display value
Display value
compensation time setting after power is applied. Y 9.000
Setting range: 00.0 to 99.9 (unit: sec) β time 6.000
βY
Factory default: 00.0 3.000
1.000 Input
value
Error display 0 X Input 0.2 0.4 0.60.8 1V
Display Description (Fig. 1) value
(example of gradient correction)
Flashes when measuring input is exceeded the max.
HHHH
allowable input (110%) ① Select 0-1VDC[1V] for measuring input in Parameter1.
Flashes when measuring input is exceeded the max. ② Standard specification in input: 0-1VDC and 1.000
LLLL
allowable input (-10%)
therefore it has to be 15.000 (H-SC) for 1VDC (input)
Flashes when display input is exceeded the max.
D-HH in order to display 3.000 for DC200mV (input). But it is
display range (9999)
disable due to setting range is 9.999
Flashes when display input is exceeded the min.
D-LL
display range (-1999) ③ In this case, please check below chart.
Flashes when measuring frequency is exceeded the max. Please set as INbH× H-SC=15.000
F-HH
measuring value (9999) Setting H-SC L-SC INbH Other
OVER Flashes when it exceeds zero adjustment range (±99) ① Disable 0.000 1.000 -
※Error display is released automatically when it is in the ② 7.500 0.000 2.000
In this case, any setting
③ 5.000 0.000 3.000
measured and display range. methods display the
④ 3.750 0.000 4.000
※"LLLL" is displayed when the measuring input is same display value.
⑤ 3.000 0.000 5.000
DC4-20mA.
※ After flashing " OVER" 2 times when it exceeds the zero
Error correction [PA 1 group: INbH / INbL]
adjustment range, it returns to RUN mode.
It corrects display value error of measured input.
INbL: ±99 [Adjust deviation of low value]
Display scale [PA 1 group: H-SC/L-SC] INbH: 5.000 to 0.100 [Correct gradient (%) of high value]
This function is to display setting (-1999 to 9999) of Display value= (measured value × INbH ) + INbL
particular High/Low-limit value in order to display High/Low- E.g.) When the measured range is 0 to 500V, and the
limit value of measured input. If measured inputs are 'a' and display range is 0 to 500.0. If the low display value is "1.2"
'b' and particular values are 'A' and 'B', it will display a=A, to 0V input, set -12 as INbL value to display ")0" by
b=B as below graphs. adjusting offset of the low value. The display value to 500V
measured input varies by adjusting the offset of low value.
Display B B B
Display Display If this display value is "501.0", calculate 500.0/501.0
value value A value (desired display value/the display value), and set the 0.998
A
a b correction value as the INbH to display 50)0 by adjusting
a b a b A
Input value Input value Input value gradient of high value.
Display A a b ※The offset correction range of INbL is within -99 to 99
Display A A
a b for D-0, D-1 digit regardless of decimal point.
value
value Display
B
value
a b
Input value
B
Input value
B
Input value
Display cycle delay [PA 2 group: D1sT]
In some applications the measured input may fluctuate
which in turn causes the display to fluctuate. By adjusting
the display cycle delay function time in the D1sT of
parameter 2, the operator can adjust the display time within
a range of 0.1 sec to 5 sec. For example, if the operator
sets the display cycle time to 4.0 sec, the display value
displayed will be the average input value over 4 sec and
also will show any changes if any every 4 sec.
L-44
Multi Panel Meter
Monitoring peak display value Sub output (A)
It monitors max./min. value of display value based on the It is able to set address (01 to 99)
current displays value and then displays the data at hPEK, It is able to transmit by selecting modulation speed (B)
Fiber
lPEK of parameter 0. Set the delay time (0 to 30 sec) (transmitted number of signal per 1 sec) of serial trans Optic
Sensors
at PEkT of parameter 2 in order to prevent malfunction -mission. (selectable 1200, 2400, 4800, 9600bps)
caused by initial overcurrent or overvoltage, when ● Low-speed serial output (C)
Door/Area
monitoring the peak value. It outputs current display value as Low-frequency (50Hz) Sensors
monitoring delay time [PEkT] of parameter 2 group is set ※Only one sub-output is selectable. (F)
as 00 sec [00 S]. (More than one sub-output is not allowed.) Rotary
Encoders
Data Dn-1 Dn D1
(T)
Software
Input
ordering 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 1 2
DP D C B A DP D C B A DP D C B A DP D C B A DP D
Clock
Data H H L H H H H H L L L H H L H H H H H L
tw
ta tb
Latch
Display
L-45