Professional Documents
Culture Documents
• Set2 : Site installed with 2 LTE700 RF Module ( 2 Sectors are far from the 3rd sector)
Scenario 2: Site with LTE1800 or LTE2100 for sharing sites using Huawei antenna with 3 Sets of installation
• Set1 : Site installed with 1 LTE700 RF Module.
• Set2 : Site installed with 2 LTE700 RF Module ( 2 Sectors are far from the 3rd sector)
Notes to be considered :
• Additional 150 Mbps will be added to the existing Bandwidth of either L1800 or L2100 based on site type.
• 6Gbit fiber cables should be used with 6Gbit SFP.
• Special Pre-fabricated jumpers for Octa antenna will be used (4.3-10 Female).
HW Used in the Project
Flexi Multiradio 10 BTS
Flexi Multiradio 10 System Module outdoor FSMF
• 10.1 – 19.7 kg
• IP65
• -35 to +55 °C
Flexi Multiradio 10 BTS
• Release 3 System Module, FSMF with FBBA and FBBC
• RL40 onwards
Optional power GE or RP3 RF RP3 RF port, RP3 RF port, RP3 RF port, Optional transport sub-
distribution sub- Combo port, OptInt #1 OptInt #2 OptInt #3 module FTIF
module FPFD OptInt #6
Sync In
BB BB
DC out DC in LMP SRIO Ext1 Ext2 GE EAC Sync Out
OPT1 OPT2 OPT3
FBBA FBBC
(RL50) (RL60)
FBBC installation
Connect Power cable from DC outport of FSMF to DC
input on FBBC
baseband extension
optical OBSAI optical OBSAI optical OBSAI The SRIO/RF4 combo port can be configured to work as fourth RP3-01
baseband extension
RP3-01 6 RP3-01 6 RP3-01 6 interface or as SRIO interface for external baseband extension, for example,
interface towards to connect additional Flexi Multiradio 10 BTS System Module in the future LTE
Gbit/s Gbit/s Gbit/s
System Module SW release.
interfaces interfaces interfaces
(QSFP)
Name Module name SW Support TX RX Obsai Rp-3 Comments
bandwidth* bandwidth*
FRPA Flexi RF Module 6*40W 700 (FRPA) 472703A LTE: RL50 6*TX: 35 MHz 6*RX: 35 MHz 3 x 6 Gb Band 28 (703-738UL & 758-793 DL)
SRAN 16.2 Output power 6 x 40W
6 Gb OBSAI RP3 SFPs:
Ports distribution /
technology
Technology Color
2300 2300
MHz/RET5 MHz/RET5
2100 1400 700 MHz Green
MHz/RET6 MHz/RET3
900 MHz White
1800 1800
MHz/RET4 MHz/RET4 1400 MHz Gray
CommScope_Dat
asheet
RET Labeling for CommScope antenna
N.B. RET cable should be connected to Antenna Sector (A) and FPRA RF module and detected from LTE700 System module whether its collocated with L1800 or L2100.
Each CommScope antenna has 6 RETs and RETs will be labeled according to its Serial Number .
I.e. Sector A antenna has 6 RETs with SN :
Ports distribution /
technology
2300 MHz/Y3 700 MHz Technology Color
/R1
700 MHz Green
Huawei_Antenna_
Datashaeet
RET Labeling for Huawei antenna
N.B. RET cable should be connected to Antenna Sector (A) and FPRA RF module and detected from LTE700 System module whether its collocated with L1800 or L2100.
Each Huawei antenna has 8 RETs and RETs will be labeled according to last 2 digits .
Last 2 digits indicates to technology Last 2 digits indicates to technology Last 2 digits indicates to technology
type. type. type.
RET Labeling for Huawei antenna
N.B. RET cable should be connected to Antenna Sector (A) and FPRA RF module and detected from LTE700 System module whether its collocated with L1800 or L2100.
Array number is the last 2 digits in the RET S/N and all RETs should be labeled according to it
Array Technology
R1 L700
R2 G/U900
Y1 G/L1800
Y2 G/L1800
Y3 L2300
Y4 L2300
Y5 L1400
Y6 L/U2100
Antenna S/N RET S/N labeling Antenna S/N RET S/N labeling Antenna S/N RET S/N labeling
701273110H9000171 M2731H9017R6637r1 Sec (A) / L700 701273110H9000174 M2731H901881925r1 Sec (B) / L700 701273110H9000182 M2731H901AN1558r1 Sec (C) / L700
701273110H9000171 M2731H9017S64RBy5 Sec (A) / L1400 701273110H9000174 M2731H9018946RBy5 Sec (B) / L1400 701273110H9000182 M2731H901AP58RBy5 Sec (C) / L1400
701273110H9000171 M2731H9017T8838r2 Sec (A) / G/U900 701273110H9000174 M2731H9018A0690r2 Sec (B) / G/U900 701273110H9000182 M2731H901AQ3610r2 Sec (C) / G/U900
701273110H9000171 M2731H9017U79RTy6 Sec (A) / L/U2100 701273110H9000174 M2731H9018B16RTy6 Sec (B) / L/U2100 701273110H9000182 M2731H901AR43RTy6 Sec (C) / L/U2100
701273110H9000171 M2731H9017V92LTy2 Sec (A) /G/L1800 701273110H9000174 M2731H9018C41LTy2 Sec (B) /G/L1800 701273110H9000182 M2731H901AS81LTy2 Sec (C) /G/L1800
701273110H9000171 M2731H9017W50CTy4 Sec (A) / L2300 701273110H9000174 M2731H9018D15CTy4 Sec (B) / L2300 701273110H9000182 M2731H901AT60CTy4 Sec (C) / L2300
701273110H9000171 M2731H9017X90LBy1 Sec (A) /G/L1800 701273110H9000174 M2731H9018E26LBy1 Sec (B) /G/L1800 701273110H9000182 M2731H901AU90LBy1 Sec (C) /G/L1800
701273110H9000171 M2731H9017Y51CBy3 Sec (A) / L2300 701273110H9000174 M2731H9018F40CBy3 Sec (B) / L2300 701273110H9000182 M2731H901AV15CBy3 Sec (C) / L2300
RET Labeling for Huawei antenna
N.B. RET cable should be connected to Antenna Sector (A) and FPRA RF module and detected from LTE700 System module whether its collocated with L1800 or L2100.
Sector number
Example of Jumpers labeling
N.B. RET cable should be connected to Antenna Sector (A) and FPRA RF module and detected from LTE700 System module whether its collocated with L1800 or L2100.
FPFD
• Power distribution unit
optional for FSMF MR10
FPFD Flexi Power Distribution for MR10
• Optional PDU to FSMF for Flexi Version Ampacity DC Input Notes
Multiradio10 BTS
.204 40A fix. up to FPCA DC dual cable not
• Integrated to MR10 FSMF core unit 50mm² needed for 240W RFM.
FPCA .203 DC cable
• IP65 protection level needed for 360W RFM
• One DC input and 4+1 DC outputs mode *)
• Suitable for all Flexi BTS installation solutions (wall, pole, mast, stack, cabinet)
Power consumption / No RF
Number of RF Modules
sharing
1 934
L700 (FRPA)
2 1082
3 1230
4 1640
Installation Guidelines
1. Label all jumpers that are connected to the existing technologies before dismantling to avoid any sectors swap in
case of Roll-back situation.
2. Dismantle all the existing antennas and jumpers from the tower and replace it with the new CommScope antenna
following the azimuth from SCO.
3. Install the new RF module for LTE700 (FPRA) with 2 SFPs.
4. RET cable should be connected to FPRA RF module and detected from LTE700 System module whether its
collocated with L1800 or L2100.
5. In case of outdoor sites , Install the new AC/DC converter FPMA.
6. RF module’s electricity (FPRA) will be derived from FPFD card or from rectifier depends on power options
availability.
7. After installing CommScope antenna , Install all jumpers for all existing technologies ; plus LTE700 as per the color
code.
8. Install FBBC card for LTE1800/2100 system module (FSMF) with 2 SFP for RF connection.
9. connect 2 fibers from system module to RF module (FBBC card OPT1 – RF module OPT1 ) (FBBC card OPT2 – RF
module OPT2 ) in case of 1 RF module is used
10. connect 1 fiber from system module to each RF module (FBBC card OPT1 – RF module1 OPT1 ) (FBBC card OPT2
– RF2 module OPT1 ) in case of 2 RF module is used
11. connect 3 fibers from system module to each RF module (FBBC card OPT1 – RF module1 OPT1 ) (FBBC card
OPT2 – RF module2 OPT1 ) (FBBC card OPT3 – RF module3 OPT1 ) in case of 3 RF module is used
Scenario 1 Site using 1 RF module with 16 ports Antenna
B
Fiber Optic
C A
If Octa/Huawei antenna will
be installed , all other
Sync cable
antennas will be dismantled
RF Jumper and all technologies will be
migrated to the Octa
antenna
Port 6
FRPA 240W
Port 5 Port 1
OPT 1
Port 2
OPT 2
Port 3
Port 4
FBBC Card
with 4 OPT FBBC/OPT 1
In case of 1 RF Module , 2
Ports FBBC/OPT 2
opt fibers will be connected
to the RF module
C B A
OPT 1 OPT 1
FBBC Card
with 4 OPT
Ports In case of 2 RF Module , 1
opt fiber will be connected
to each RF module
LTE1800 or LTE2100 G1800 or U2100
Scenario 1 Site using 3 RF module with 16 ports Antenna ( Wall-mount)
C
B A If Octa/Huawei antenna
will be installed , all other
antennas will be
Port 1 Port 2 Port 1 Port 2 Port 1
Port 2
dismantled and all
technologies will be
migrated to the Octa
antenna
OPT 1 OPT 1
OPT 1
FBBC Card
with 4 OPT In case of 3 RF Module , 1
Ports opt fiber will be
connected to each RF
module
LTE1800 or LTE2100 G1800/U2100
OPT 1
OPT 3
OPT 2
L700 Commissioning
Cell 1
Cell 2
Cell 3
L700 Commissioning