Professional Documents
Culture Documents
PLEASE EDIT ONLY LIGHT BLUE CELLS (BOX) NOT OTHER CELLS
THANKS!
ENGR. LEANDRO B. PICZON II (leandrobpiczonii@hotmail.com)
Professional Regulation Commission Number 0088397
Gandara, Samar, Philippines
…..............................................................................................
NOTE:
Least Input Value is 0.001
Turn ON/OFF Earthquake Analysis by inputing ON or OFF
When analyzing 3 storey building just put the total height
of the building, the number of storeies and the
and column and beam on the ground floor is
computed, like wise the 2nd floor will be computed
less the height of ground floor, number of stories
shall be 1 and the lowest floor column and beam
is computed and so on...P.S. wind height value
should be the total height of the building
Page 1
INTRO
RELEASED 7.7 Minor Fixes
RELEASED 7.8 Additional Features
RELEASED 7.9 Additional Features
RELEASED 8.0 Additional Features
RELEASED 9.0 Major Fixes
RELEASED 9.2 Minor Fixes
RELEASED 9.3 Live Load Reduction Added
Page 2
INTRO
Dedication Public License (DPL)
I. Freeware
First of all, the reasons why My Structural Analysis is free:
I.a. Dedication
My Structural Analysis is dedicated to the most wonderful people on earth :) Annabelle, Papa Leandro I and Mama Isab
My Structural Analysis is dedicated to the most wonderful place on earth :) Gandara, Samar, Philippines 6706
I.b. Binary
What do you get if you buy software? Lots of ones and zeros, nothing more. If they were distributed as art, I could understand p
is to earn money - by fees or ads - I don't like it!
I.c. Conclusion
This means that I grant you the license to use My Structural Analysis as much as you like. But if you like it, I ask two things of y
wonderful girl and parents you're at it ;) ) to your god - or whatever you believe - and wish us some luck.
II. Limitations
I can also give you no warranty that My Structural Analysis will calculate any structural forms, or that it will give you no false po
of the problem is shown with every entry, and if you have any questions remaining you can visit the support forum for more info
II.c. Liability
Under no circumstances can you make me liable for any damage, however caused, including, but not limited to damage you m
My Structural analysis.
II.d. Use of application in whole
Free use is limited to the application in whole. Usage of parts only, for example the database or the plug-ins, is not permitted.
III. Distribution
Here are some basic rules about distributing My Structural Analysis.
III.b. Mirroring
If you want to mirror “My Structural Analysis”, feel free to do so as long as you don't modify the original archive. If you want to b
you can subscribe to the mailing list.
Page 3
INTRO
III.c. Publishing
You may publish My Structural Analysis in a book or magazine (or other media) by simply sending a written request for permiss
needs. I request a copy of the media in which My Structural Analysis is published as compensation.
Page 4
INTRO
ere distributed as art, I could understand paying it. But if the main goal of their order
like. But if you like it, I ask two things of you: say a prayer for me (and the most
wish us some luck.
s in the honesty of the code, I will give insight to a trusted organization like a
that has to be removed after the evaluation time has ended).
and I give you the warranty that I placed no code to cause intentional harm
m sometimes, and I cannot guarantee that your system will be running the
al forms, or that it will give you no false positives. For your own verification the location
u can visit the support forum for more information.
ncluding, but not limited to damage you might do to your system using
e terms, there is a license for corporate users that can be found at safer-networking.ie.
modify the original archive. If you want to be kept up to date about major updates,
Page 5
INTRO
mply sending a written request for permission, including a description of your specific
Page 6
Proof
GIVEN
fc' 21 Mpa
fy 275 Mpa
As' 1500 mm2 bars in compression
As 3500 mm2 bars in tension
d 425 mm
d' 75 mm
h 500 mm
b 300 mm
SOLUTION
determine if compression bars yielded
assuming Es>es
As=As2
As2 1500 mm2
As1 3500-1500 mm2
C= As1fy
0.85fc'ab = As1fy
a = (As1*(fy))/(0.85*fc'*b)
a = 102.71mm
Es = ((c-d')/c)*0.003
Es = 0.0011
since Es <es=0.003
compression steel has not yielded as assumed
c' = As'fs'
determine Mu
first solve for the value of c (exact analysis)
C+C' = Asfy
0.85fc'ab+As'fs' = Asfy
a=B1c
fs'=Eses
Es'=((c-d')/c)*0.003
fs'=(((c-d')/c)*0.003)*200000
fs'=600((c-d')/c)
substituting
0.85fc'(B1c)b+As'(600((c-d')/c)=Asfy
c=128.8mm
a=109.48
Mn1=c(d-(a/2)
c=0.85fc'ab
Mn1=217.07x106 N-mm
Mn2=c'(d-d')
c'=As'fs'
Mn2=131.58x106 N-mm
MN=Mn1+mn2
Mn=348.05Kn-m
Mu=øMn
Mu=313.78KN-m
Page 7
Proof
try it on one of the beam design, override d' with 75mm
Page 8
Analysis
My Structural Analysis
Computing for LIVE LOAD
Weight of Person + Environment 70.00
Gravity Constant 9.81
Weight in Newtons 686.70
0.69
Number of Person/s per Square Meter 0.50
Slab Self Weight
Thickness 100.00
3.83
CHB per SQ.M. 100.00
0.98
DEAD LOAD 5.08
LIVE LOAD 0.36
Total Actual Load LL + Slab 5.42
Internal Span
Area
Slab 1 Short Span 1.65 (Side X) 0.00
0.13 7.67
Long Span 4.65 (Side Y) 4.40
Area
Slab 2 Short Span 4.50 (Side X) 3.70
0.94 20.93
Long Span 4.65 (Side Y) 4.40
Area
Slab 3 Short Span 3.95 (Side X) 3.70
0.77 17.78
Long Span 4.50 (Side Y) 1.50
Area
Slab 4 Short Span 1.65 (Side X) 0.00
0.17 6.52
Long Span 3.95 (Side Y) 1.50
Storey height
Cp Cp Storey height
4,4m 4,4m
Beam 2D
Beam 2A
Beam 1D Cp Beam 1A Cp
Page 1
Beam 2D
Beam 2A
Analysis
0,001m 3,7m
Cd BEAM 4 C1 BEAM 2 Cb
0,001m 3,7m
Beam 2B
Beam 1B Cp
1,5m 1,5m
BEAM 3
SLAB 4 SLAB 3
Cc
Alternate Cross-Beam
Beam 1A Ca to C1 Ca 0.0 C1 4.4 base 0.0 mts
Beam 2A Cb to C1 Cb 0.0 C1 3.7 base 0.0 mts
Beam 1B Ca to C1 Ca 0.0 C1 3.7 base 0.0 mts
Beam 2B Cb to C1 Cb 0.0 C1 0.0 base 0.0 mts
Beam 1B Ca to C1 Ca 0.0 C1 0.0 base 0.0 mts
Beam 2B Cb to C1 Cb 0.0 C1 1.5 base 0.0 mts
Beam 1D Ca to C1 Ca 0.0 C1 4.4 base 0.0 mts
Beam 2D Cd to C1 Cd 0.0 C1 0.0 base 0.0 mts
Planted Column on Alt. Beam
Top Reaction 0.0 KN Ca to C1 Ca 0.0 C1 3.7 base 0.0 mts
Top Reaction 0.0 KN Cb to C1 Cb 0.0 C1 4.4 base 0.0 mts
Top Reaction 0.0 KN Ca to C1 Ca 0.0 C1 0.0 base 0.0 mts
Top Reaction 0.0 KN Cb to C1 Cb 0.0 C1 3.7 base 0.0 mts
Top Reaction 0.0 KN Ca to C1 Ca 0.0 C1 1.5 base 0.0 mts
Top Reaction 0.0 KN Cb to C1 Cb 0.0 C1 0.0 base 0.0 mts
Top Reaction 0.0 KN Ca to C1 Ca 0.0 C1 0.0 base 0.0 mts
Top Reaction 0.0 KN Cd to C1 Cd 0.0 C1 1.5 base 0.0 mts
Page 2
Analysis
Beam 1 Slab 1 effect 11.43
Slab 2 effect 8.21
Total LL+Slab effect on Beam 1 19.64
Page 3
Analysis
T= Ct(hn)3/4
T= 0.20
Applied Weight W= 73.72
Number of Storey 2
Design considered plus 1 storey
Overhang/Cantilever
Area
Slab 5 Short Span 0.00 (Side X) 1.50
1.00 0.00
Long Span 0.00 (Side Y) 3.70
Area
Slab 6 Short Span 0.00 (Side X) 1.50
1.00 0.00
Long Span 0.00 (Side Y) 0.00
Area
Page 4
Analysis
Slab 5A Short Span 0.00 (Side X) 5.01
1.00 0.00
Long Span 0.00 (Side Y) 3.70
Area
Slab 6A Short Span 0.00 (Side X) 5.01
1.00 0.00
Long Span 0.00 (Side Y) 0.00
1.5
Ca Bottom Reaction
Ca Ja
Cb Bottom Reaction
BEAM 5A
3.7
BEAM 5
0.0
Cb Jc
1.5
Alternate Cross-Beam
Beam 1A Ca to C2 Ca 0.0 C2 3.7 base 0.0 mts
Beam 2A Jb to C2 Jb 0.0 C2 0.0 base 0.0 mts
Beam 1B Ca to C2 Ca 0.0 C2 0.0 base 0.0 mts
Beam 2B Cb to C2 Cb 0.0 C2 3.7 base 0.0 mts
Beam 1B Ca to C2 Ca 0.0 C2 0.0 base 0.0 mts
Beam 2B Cb to C2 Cb 0.0 C2 5.0 base 0.0 mts
Beam 1D Ca to C2 Ca 0.0 C2 1.5 base 0.0 mts
Beam 2D Cd to C2 Cd 0.0 C2 0.0 base 0.0 mts
Planted Column on Alt. Beam
Top Reaction 0.0 KN Ca to C1 Ca 0.0 C2 1.5 base 0.0 mts
Top Reaction 0.0 KN Cb to C1 Cb 0.0 C2 5.0 base 0.0 mts
Top Reaction 0.0 KN Ca to C1 Ca 0.0 C2 3.7 base 0.0 mts
Top Reaction 0.0 KN Cb to C1 Cb 0.0 C2 0.0 base 0.0 mts
Top Reaction 0.0 KN Ca to C1 Ca 0.0 C2 5.0 base 0.0 mts
Page 5
Analysis
Top Reaction 0.0 KN Cb to C1 Cb 0.0 C2 0.0 base 0.0 mts
Top Reaction 0.0 KN Ca to C1 Ca 0.0 C2 0.0 base 0.0 mts
Top Reaction 0.0 KN Cd to C1 Cd 0.0 C2 0.0 base 0.0 mts
Page 6
Analysis
Page 7
Analysis
87.64
Overhang/Cantilever/Corner
Area
Slab 7 Short Span 0.00 (Side X) 0.00
1.00 0.00
Long Span 0.00 (Side Y) 0.00
Area
Slab 8 Short Span 0.00 (Side X) 0.00
1.00 0.00
Long Span 0.00 (Side Y) 0.00
Page 8
Analysis
Ca Bottom Reaction
Ca Ja
Cb Bottom Reaction
0.0
BEAM 8
BEAM 14
Storey height
SLAB 10 0.0 SLAB 7 0.0 Storey height
Storey height
0.0 Storey height
Storey height
Storey height
Cb BEAM 15 C3 BEAM 12 Jd
Storey height
0.0 Storey height
BEAM 13
0.0
Jb BEAM 11 Jc BEAM 10
0.001
Page 9
Analysis
Beam 12 Slab 7 effect 0.00
Slab 8 effect 0.00
Total LL+Slab effect on Beam 6 0.00
Page 10
Analysis
Shear (WultL/2) 10.83
0.01
Page 11
Analysis
Beam 8 R8=Vu/2 0.00
Beam 9 R9=Vu 0.00
Beam 10 R10=Vu 0.00
Beam 11 R11=Vu/2 0.00
Beam 12 R12=Vu/2+R8+R9 0.00
Beam 13 R13=Vu/2+R10+R11 0.00
Beam 14 R14=Vu/2 0.00
Beam 15 R15=Vu/2 0.00
Wind Load
Location Samar
Heigth above ground 6.40
Analytical Procedure NSCP 2-56 exposure = B
NSCP 2-61 Ce = 0.78
NSCP 2-62 Cq = 1.40
NSCP 2-62 Cq = 1.40
NSCP 2-64 qs = 2000.00
NSCP 2-50 I= 1.00
Standard Occupancy
WLPpre = 2184
WLPsuc = 2184
use 1.80
Page 12
Analysis
70.00 kgs
9.81 m/sec2
686.70 Newton (N)
0.69 KiloNewton (KN)
0.50 person/s
100.00 millimeter
3.83 KN/m2
100.00 kgs
0.98 KN/m2
5.08 KN/m2
0.36 KN/m2
5.42 KN/m2
3.70
5.00
18.50 YES
3.87 %
0.00 Meter/s
4.40 Meter/s
3.70 Meter/s
4.40 Meter/s
3.70 Meter/s
1.50 Meter/s
0.00 Meter/s
1.50 Meter/s
mts
height 0.0 mts
height 0.0 mts
height 0.0 mts
height 0.0 mts
mts
Storey height 0.0
Storey height 0.0
Storey height 0.0
Storey height 0.0
Page 13
Analysis
Page 14
Analysis
11.43 KN/m
8.21 KN/m
19.64 KN/m
6.69 KN/m
7.46 KN/m
14.15 KN/m
2.71 KN/m
3.83 KN/m
6.54 KN/m
0.00 KN/m
0.00 KN/m
0.00 KN/m
12.946 KN/m
7.732 KN/m
9.027 KN/m
8.788 KN/m
33.23 KN/m
80.43 KN-m
33.23 KN/m
73.12 KN
22.27 KN/m
38.10 KN-m
22.27 KN/m
41.20 KN
16.02 KN/m
4.51 KN-m
16.02 KN/m
12.02 KN
Page 15
Analysis
9.23 KN/m
0.00 KN-m
9.23 KN/m
0.01 KN
36.56 KN
20.60 KN
6.01 KN
0.00 KN
ON
21.471 KN
0.40
1.00
10.00
7.28
2.00
6.40 mts
0.05
0.20
73.72 KN
181.13 KN
34.35 KN-m
0.20 meter
0.30 meter
6.40 meter
10.55 KN
147.45 KN
2 Storeies
gn considered plus 1 storey
1.50 Meter/s
3.70 Meter/s
1.50 Meter/s
0.00 Meter/s
Page 16
Analysis
5.01 Meter/s
3.70 Meter/s
5.01 Meter/s
0.00 Meter/s
mts
height 0.0 mts
height 0.0 mts
height 0.0 mts
height 0.0 mts
height 0.0 mts
height 0.0 mts
KN
KN
mts
Storey height 0.0
Storey height 0.0
Storey height 0.0
Storey height 0.0
Storey height 0.0
Storey height 0.0
Storey height 0.0
Storey height 0.0
Page 17
Analysis
height 0.0 mts
height 0.0 mts
height 0.0 mts
mts
Storey height 0.0
Storey height 0.0
Storey height 0.0
Storey height 0.0
Storey height 0.0
Storey height 0.0
Storey height 0.0
Storey height 0.0
6.69 KN/m
6.69 KN/m
0.00 KN/m
KN/m
0.00 KN/m
2.71 KN/m
0.00 KN/m
2.71 KN/m
6.69 KN/m
6.69 KN/m
13.38 KN/m
0.00 KN/m
0.00 KN/m
0.00 KN/m
9.06 KN/m
9.06 KN/m
18.12 KN/m
1.64 KN/m
Page 18
Analysis
8.48 KN/m
0.00 KN/m
16.07 KN/m
8.38 KN/m
16.07 KN/m
8.41 KN/m
14.39 KN-m
8.41 KN/m
15.56 KN
8.91 KN/m
0.00 KN-m
8.91 KN/m
0.01 KN
2.71 KN/m
16.41 KN-m
2.71 KN/m
12.47 KN
13.38 KN/m
22.90 KN-m
30.25 KN/m
55.96 KN
8.80 KN/m
0.00 KN-m
8.80 KN/m
0.01 KN
18.12 KN/m
56.84 KN-m
34.99 KN/m
Page 19
Analysis
87.64 KN
7.78 KN
0.00 KN
14.02 KN
27.98 KN
0.00 KN
43.82 KN
90.232 KN
0.40
1.00
10.00
7.28
2.00
6.40 mts
0.05
0.20
309.81 KN
581.52 KN
144.37 KN-m
0.20 meter
0.40 meter
6.40 meter
223.99 KN
619.63 KN
2.00 Storeies
0.00 Meter/s
0.00 Meter/s
0.00 Meter/s
0.00 Meter/s
0.00 Meter/s
0.00 Meter/s
Page 20
Analysis
0.00 Meter/s
0.00 Meter/s
mts
height 0.0 mts
height 0.0 mts
height 0.0 mts
height 0.0 mts
height 0.0 mts
height 0.0 mts
KN
KN
mts
Storey height 0.0
Storey height 0.0
Storey height 0.0
Storey height 0.0
Storey height 0.0
Storey height 0.0
Storey height 0.0
Storey height 0.0
0.00 KN/m
0.00 KN/m
0.00 KN/m
KN/m
0.00 KN/m
0.00 KN/m
KN/m
0.00 KN/m
0.00 KN/m
0.00 KN/m
Page 21
Analysis
0.00 KN/m
0.00 KN/m
0.00 KN/m
0.00 KN/m
0.00 KN/m
0.00 KN/m
0.00 KN/m
0.00 KN/m
0.00 KN/m
0.00 KN/m
0.00 KN/m
0.00 KN/m
10.32 KN/m
0.00 KN/m
0.00 KN/m
0.00 KN/m
0.00 KN/m
0.00 KN/m
0.00 KN/m
2.28 KN/m
10.83 KN/m
0.00 KN-m
Page 22
Analysis
10.83 KN/m
0.01 KN
0.00 KN/m
0.00 KN-m
0.00 KN/m
0.00 KN
0.00 KN/m
0.00 KN-m
0.00 KN/m
0.00 KN
0.00 KN/m
0.00 KN-m
0.00 KN/m
0.00 KN
0.00 KN/m
0.01 KN-m
0.00 KN/m
0.01 KN
0.00 KN/m
0.00 KN-m
0.00 KN/m
0.00 KN
0.00 KN/m
0.00 KN-m
0.00 KN/m
0.00 KN
0.00 KN/m
0.00 KN-m
2.40 KN/m
0.00 KN
Page 23
Analysis
0.00 KN
0.00 KN
0.00 KN
0.00 KN
0.00 KN
0.00 KN
0.00 KN
0.00 KN
0.002 KN
0.400
1.000
10.000
7.281
2.000
6.400 mts
0.050
0.201
0.01 KN
0.01 KN
0.00 KN-m
0.00 meter
0.00 meter
6.40 meter
0.00 KN
0.01 KN
2.00 Storeies
Samar
6.40 mm
B
0.78
1.40 outward
1.40 inward
2000.00 Pascal
1.00
Standard Occupancy
2184 Pascal
2184 Pascal
1.80 KPA
Page 24
SLAB
REINFORCED CONCRETE SLAB DESIGN
SLAB 1
Edge 1
C = Continuous
Ls 3700 mm D = Discontinuous
EDGE CONDITIONS
Edge 4
Edge 2
Edge 1 c
Edge 2 C
Ll 5000 mm Edge 3 C
Edge 4 C
Edge 3
SHORT SPAN LONG SPAN
LENGTH OF SLAB SPAN mm 3700 5000
2 WAY 0.74
Steel Yield Strength MPA 275
Concrete Compressive Strength MPA 21
Concrete Cover mm 20
ASSUMED SLAB THICKNESS mm 100.0
Minimum Thickness OK mm 96.7
Maximum Thickness OK mm 139.0
Smax=2t mm 200
Concrete Density kN/m3 23.5
LOADS
Selfweight kN/m2 3.83
Dead Load kN/m 2
0.98
Live Load kN/m2 1.59
Actual Load kN/m 2
9.59
Page 1
SLAB
per M length
EDGE 4
0.032
4.20
12
200
T1
74.00
0.0076
0.0051
0.0378
0.0284
0.0076
9.32
SAFE
DUCTILE
136
Page 2
STAIRS
REINFORCED CONCRETE STAIRS DESIGN
SLAB 1
Edge 1
C = Continuous
Ls 1200 mm D = Discontinuous
EDGE CONDITIONS
Edge 4
Edge 2
Edge 1 D
Edge 2 D
Ll 6000 mm Edge 3 D
Edge 4 D
Edge 3
SHORT SPAN LONG SPAN
LENGTH OF SLAB SPAN mm 1200 6000
1 WAY 0.20
Steel Yield Strength MPA 275
Concrete Compressive Strength MPA 21
Concrete Cover mm 20
ASSUMED SLAB THICKNESS mm 82.0
Minimum Thickness OK mm 80.0
Maximum Thickness OK mm 166.8
Smax=2t mm 164
Concrete Density kN/m3 23.5
LOADS
Selfweight kN/m2 3.39
Dead Load kN/m 2
0.98
Live Load kN/m2 1.59
Actual Load kN/m 2
10.63
Page 1
STAIRS
per M length
EDGE 4
0.000
0.00
12
320
T1
56.00
0.0063
0.0051
0.0378
0.0284
0.0063
4.41
SAFE
DUCTILE
136
Page 2
BEAM1
Summary Results @ Midspan BEAM 1
Bending Moment Capacity Mu = 125.10 KN-m
Moment Applied Moment Mz = 120.55 KN-m
Capacity Status PASS
Shear -96.39 KN
Cross-Section Dimensions
Height of Beam mm 400
Width of Beam mm 350
Length of Beam mm 4400
Reinforcement data
Bottom Bars 5
First layer bars
Number of Reinforce Bars (1) 5
BAR (1) SIZE mm 16
Second layer bars
Number of Reinforce Bars (2) 2
BAR (2) SIZE mm 16
Top Bars
Number of Reinforce Bars (1) 3
BAR (1) SIZE mm 16
Weight of Main Bars kgs 4090.98
Stirrup Size mm 10
Strength Reduction Factor 0.9
Steel Yield Strength MPA 275
Concrete Compressive Strength MPA 21
Concrete Cover mm 40
AREA OF ONE BAR (first layer) mm2 201.06
AREA OF ONE BAR (second layer) mm2 0
AREA OF ONE BAR (compression) mm2 201.06
Total Area of Compression Reinforcement Bars mm2 603.19
Total Area of Tensile Reinforcement Bars mm2 1005.31
EFFECTIVE DEPTH OF BEAM mm 326.00
Tensile STEEL RATIO 0.0088
Compression STEEL RATIO 0.0053
MINIMUM STEEL RATIO 0.0051
Factor b1 0.850
Reinforcement ratio producing balanced strain condition 0.0378
MAXIMUM STEEL Reinforcement RATIO 0.0284
MAXIMUM STEEL Double Reinforcement RATIO 0.0337
Steel Reinforcement Ratio at Center of Gravity 0.0203
Compression Steel does not Yield
Ductility Test Beam is: Ductile
Shear Reinforcement
Page 3
BEAM1
face of support (mm) (KN) (KN) (KN) (mm) (mm)
50 to 326.00 46.59 -178.50 143.19 98.35 163.00
326.00 733.33 196.03 -160.65 292.63 108.25 81.50
733.33 1233.33 329.69 -138.75 426.29 124.98 CHECK SHEAR
1233.33 1733.33 463.35 -116.84 559.95 133.72 CHECK SHEAR
1733.33 2233.33 597.01 -94.93 693.61 139.09 CHECK SHEAR
2233.33 rest at #VALUE! #VALUE! #VALUE! #VALUE! #VALUE!
Support
L/2
1@50mm
0 to d
d to1733,33
1733,33 to 2233,33
follow table rest at Smax
Page 4
BEAM1
Ductile
Use
Page 5
BEAM1
(mm)
98.35
81.50
124.98
133.72
139.09
#VALUE!
Page 6
BEAM2
Summary Results @ Midspan BEAM 2
Bending Moment Capacity Mu = 91.50 KN-m
Moment Applied Moment Mz = 78.22 KN-m
Capacity Status PASS
Shear -64.47 KN
Cross-Section Dimensions
Height of Beam mm 400
Width of Beam mm 200
Length of Beam mm 3000
Reinforcement data
Bottom Bars 1
First layer bars
Number of Reinforce Bars (1) 3
BAR (1) SIZE mm 16
Second layer bars
Number of Reinforce Bars (2) 0.001
BAR (2) SIZE mm 0.001
Top Bars
Number of Reinforce Bars (1) 3
BAR (1) SIZE mm 16
Weight if Bars kgs 2091.98
Stirrup Size mm 10
Strength Reduction Factor 0.9
Steel Yield Strength MPA 275
Concrete Compressive Strength MPA 21
Concrete Cover mm 40
AREA OF ONE BAR (first layer) mm2 201.06
AREA OF ONE BAR (second layer) mm2 0
AREA OF ONE BAR (compression) mm2 201.06
Total Area of Compression Reinforcement Bars mm2 603.19
Total Area of Tensile Reinforcement Bars mm2 603.19
EFFECTIVE DEPTH OF BEAM mm 326.00
Tensile STEEL RATIO 0.0093
Compression STEEL RATIO 0.0093
MINIMUM STEEL RATIO 0.0051
Factor b1 0.850
Reinforcement ratio producing balanced strain condition 0.0378
MAXIMUM STEEL Reinforcement RATIO 0.0284
MAXIMUM STEEL Double Reinforcement RATIO 0.0376
Steel Reinforcement Ratio at Center of Gravity 0.0242
Compression Steel does not Yield
Ductility Test Beam is: Ductile
Shear Reinforcement
Page 1
BEAM2
face of support (mm) (KN) (KN) (KN) (mm) (mm)
50 to 326.00 15.21 -114.93 74.58 188.83 163.00
326.00 500.00 76.38 -107.45 135.74 159.12 81.50
500.00 1000.00 152.75 -85.96 212.12 203.65 CHECK SHEAR
1000.00 1500.00 229.13 -64.47 288.49 224.60 CHECK SHEAR
1500.00 rest at #VALUE! #VALUE! #VALUE! #VALUE! #VALUE!
rest at rest at #VALUE! #VALUE! #VALUE! #VALUE! #VALUE!
Support
L/2
1@50mm
0 to d
d to1500
#VALUE!
follow table rest at Smax
Page 2
BEAM2
Ductile
Use
Page 3
BEAM2
(mm)
163.00
81.50
203.65
224.60
#VALUE!
#VALUE!
Page 4
BEAM3
Summary Results @ Midspan BEAM 3
Bending Moment Capacity Mu = 91.50 KN-m
Moment Applied Moment Mz = 44.63 KN-m
Capacity Status PASS
Shear -35.29 KN
Cross-Section Dimensions
Height of Beam mm 400
Width of Beam mm 200
Length of Beam mm 1500
Reinforcement data
Bottom Bars 1
First layer bars
Number of Reinforce Bars (1) 3
BAR (1) SIZE mm 16
Second layer bars
Number of Reinforce Bars (2) 0.001
BAR (2) SIZE mm 0.001
Top Bars
Number of Reinforce Bars (1) 3
BAR (1) SIZE mm 16
Weight if Bars kgs 1045.99
Stirrup Size mm 10
Strength Reduction Factor 0.9
Steel Yield Strength MPA 275
Concrete Compressive Strength MPA 21
Concrete Cover mm 40
AREA OF ONE BAR (first layer) mm2 201.06
AREA OF ONE BAR (second layer) mm2 0
AREA OF ONE BAR (compression) mm2 201.06
Total Area of Compression Reinforcement Bars mm2 603.19
Total Area of Tensile Reinforcement Bars mm2 603.19
EFFECTIVE DEPTH OF BEAM mm 326.00
Tensile STEEL RATIO 0.0093
Compression STEEL RATIO 0.0093
MINIMUM STEEL RATIO 0.0051
Factor b1 0.850
Reinforcement ratio producing balanced strain condition 0.0378
MAXIMUM STEEL Reinforcement RATIO 0.0284
MAXIMUM STEEL Double Reinforcement RATIO 0.0376
Steel Reinforcement Ratio at Center of Gravity 0.0242
Compression Steel does not Yield
Ductility Test Beam is: Ductile
Shear Reinforcement
Page 1
BEAM3
face of support (mm) (KN) (KN) (KN) (mm) (mm)
50 to 326.00 15.21 -55.24 38.69 364.01 163.00
326.00 250.00 38.19 -58.82 61.66 175.14 163.00
250.00 750.00 114.56 -35.29 138.04 234.70 81.50
750.00 rest at #VALUE! #VALUE! #VALUE! #VALUE! #VALUE!
rest at rest at #VALUE! #VALUE! #VALUE! #VALUE! #VALUE!
rest at rest at #VALUE! #VALUE! #VALUE! #VALUE! #VALUE!
Support
L/2
1@50mm
0 to d
#VALUE!
#VALUE!
follow table rest at Smax
Page 2
BEAM3
Ductile
Use
Page 3
BEAM3
(mm)
163.00
163.00
81.50
#VALUE!
#VALUE!
#VALUE!
Page 4
BEAM4
Summary Results @ Midspan BEAM 4
Bending Moment Capacity Mu = 84.55 KN-m
Moment Applied Moment Mz = 40.12 KN-m
Capacity Status PASS
Shear -21.48 KN
Cross-Section Dimensions
Height of Beam mm 375
Width of Beam mm 190
Length of Beam mm 1
Reinforcement data
Bottom Bars 1
First layer bars
Number of Reinforce Bars (1) 3
BAR (1) SIZE mm 16
Second layer bars
Number of Reinforce Bars (2) 0.001
BAR (2) SIZE mm 0.001
Top Bars
Number of Reinforce Bars (1) 3
BAR (1) SIZE mm 16
Weight if Bars kgs 0.70
Stirrup Size mm 10
Strength Reduction Factor 0.9
Steel Yield Strength MPA 275
Concrete Compressive Strength MPA 21
Concrete Cover mm 40
AREA OF ONE BAR (first layer) mm2 201.06
AREA OF ONE BAR (second layer) mm2 0
AREA OF ONE BAR (compression) mm2 201.06
Total Area of Compression Reinforcement Bars mm2 603.19
Total Area of Tensile Reinforcement Bars mm2 603.19
EFFECTIVE DEPTH OF BEAM mm 309.00
Tensile STEEL RATIO 0.0103
Compression STEEL RATIO 0.0103
MINIMUM STEEL RATIO 0.0051
Factor b1 0.850
Reinforcement ratio producing balanced strain condition 0.0378
MAXIMUM STEEL Reinforcement RATIO 0.0284
MAXIMUM STEEL Double Reinforcement RATIO 0.0386
Steel Reinforcement Ratio at Center of Gravity 0.0261
Compression Steel does not Yield
Ductility Test Beam is: Ductile
Shear Reinforcement
Page 1
BEAM4
face of support (mm) (KN) (KN) (KN) (mm) (mm)
50 to 309.00 13.01 13231.20 15578.37 0.86 CHECK SHEAR
309.00 0.17 0.02 -35.80 15591.36 0.00 CHECK SHEAR
0.17 500.17 72.58 21443.42 15518.80 1.39 CHECK SHEAR
500.17 rest at #VALUE! #VALUE! #VALUE! #VALUE! #VALUE!
rest at rest at #VALUE! #VALUE! #VALUE! #VALUE! #VALUE!
rest at rest at #VALUE! #VALUE! #VALUE! #VALUE! #VALUE!
Support
L/2
1@50mm
0 to d
#VALUE!
#VALUE!
follow table rest at Smax
Page 2
BEAM4
Ductile
Use
Page 3
BEAM4
(mm)
0.86
0.00
1.39
#VALUE!
#VALUE!
#VALUE!
Page 4
BEAM5
Summary Results @ Midspan BEAM 5
Bending Moment Capacity Mu = 0.00 KN-m
Moment Applied Moment Mz = 164.53 KN-m
Capacity Status FAIL
Shear -107.60 KN
Cross-Section Dimensions
Height of Beam mm 300
Width of Beam mm 200
Length of Beam mm 3700
Reinforcement data
Bottom Bars 1
First layer bars
Number of Reinforce Bars (1) 0.001
BAR (1) SIZE mm 0.001
Second layer bars
Number of Reinforce Bars (2) 0.001
BAR (2) SIZE mm 0.001
Top Bars
Number of Reinforce Bars (1) 0.001
BAR (1) SIZE mm 0.001
Weight if Bars kgs 0.00
Stirrup Size mm 10
Strength Reduction Factor 0.9
Steel Yield Strength MPA 275
Concrete Compressive Strength MPA 21
Concrete Cover mm 40
AREA OF ONE BAR (first layer) mm2 0.00
AREA OF ONE BAR (second layer) mm2 0
AREA OF ONE BAR (compression) mm2 0.00
Total Area of Compression Reinforcement Bars mm2 0.00
Total Area of Tensile Reinforcement Bars mm2 0.00
EFFECTIVE DEPTH OF BEAM mm 250.00
Tensile STEEL RATIO 0.0000
Compression STEEL RATIO 0.0000
MINIMUM STEEL RATIO 0.0051
Factor b1 0.850
Reinforcement ratio producing balanced strain condition 0.0378
MAXIMUM STEEL Reinforcement RATIO 0.0284
MAXIMUM STEEL Double Reinforcement RATIO 0.0284
Steel Reinforcement Ratio at Center of Gravity 0.0163
Compression Steel does not Yield
Ductility Test Beam is: Ductile
Shear Reinforcement
Page 1
BEAM5
face of support (mm) (KN) (KN) (KN) (mm) (mm)
50 to 250.00 11.67 -200.65 121.14 89.14 62.50
250.00 616.67 94.20 -179.33 203.68 130.79 CHECK SHEAR
616.67 1116.67 170.57 -150.25 280.05 172.24 CHECK SHEAR
1116.67 1616.67 246.95 -121.17 356.43 195.93 CHECK SHEAR
1616.67 2116.67 323.33 -92.09 432.80 211.26 CHECK SHEAR
2116.67 rest at #VALUE! #VALUE! #VALUE! #VALUE! #VALUE!
Support
L/2
1@50mm
0 to d
d to1616,67
1616,67 to 2116,67
follow table rest at Smax
Page 2
BEAM5
Ductile
Use
Page 3
BEAM5
(mm)
62.50
130.79
172.24
195.93
211.26
#VALUE!
Page 4
BEAM5A
Summary Results@ Midspan BEAM 5A
Bending Moment Capacity Mu = 179.24 KN-m
Moment Applied Moment Mz = 166.55 KN-m
Capacity Status PASS
Shear -104.50 KN
Cross-Section Dimensions
Height of Cantilever Beam mm 400
Width of Cantilever Beam mm 200
Length of Cantilever Beam mm 3700
Reinforcement data
Bottom Bars 2
First layer bars
Number of Reinforce Bars (1) 3
BAR (1) SIZE mm 16
Second layer bars
Number of Reinforce Bars (2) 2
BAR (2) SIZE mm 20
Top Bars
Number of Reinforce Bars (1) 5
BAR (1) SIZE mm 17.6
Weight if Bars kgs 5235.47
Stirrup Size mm 10
Strength Reduction Factor 0.9
Steel Yield Strength MPA 275
Concrete Compressive Strength MPA 21
Concrete Cover mm 40
AREA OF ONE BAR (first layer) mm2 201.06
AREA OF ONE BAR (second layer) mm2 314.16
AREA OF ONE BAR (compression) mm2 243.29
Total Area of Compression Reinforcement Bars mm2 1216.43
Total Area of Tensile Reinforcement Bars mm2 1231.51
EFFECTIVE DEPTH OF BEAM mm 334.00
Tensile STEEL RATIO 0.0184
Compression STEEL RATIO 0.0182
MINIMUM STEEL RATIO 0.0051
Factor b1 0.850
Reinforcement ratio producing balanced strain condition 0.0378
MAXIMUM STEEL Reinforcement RATIO 0.0284
MAXIMUM STEEL Double Reinforcement RATIO 0.0466
Steel Reinforcement Ratio at Center of Gravity 0.0331
Compression Steel does not Yield
Ductility Test Beam is: Ductile
Shear Reinforcement
Page 1
BEAM5A
face of support (mm) (KN) (KN) (KN) (mm) (mm)
50 to 334.00 15.59 -190.13 116.33 124.02 83.50
334.00 616.67 94.20 -174.17 194.94 136.65 83.50
616.67 1116.67 170.57 -145.92 271.32 177.79 CHECK SHEAR
1116.67 1616.67 246.95 -117.68 347.70 200.85 CHECK SHEAR
1616.67 2116.67 323.33 -89.44 424.07 215.61 CHECK SHEAR
2116.67 rest at #VALUE! #VALUE! #VALUE! #VALUE! #VALUE!
Support
L/2
1@50mm
0 to d
d to1616,67
1616,67 to 2116,67
follow table rest at Smax
Page 2
BEAM5A
Ductile
Use
Page 3
BEAM5A
(mm)
83.50
83.50
177.79
200.85
215.61
#VALUE!
Page 4
BEAM6
Summary Results @ Midspan BEAM 6
Bending Moment Capacity Mu = 62.53 KN-m
Moment Applied Moment Mz = 20.00 KN-m
Capacity Status PASS
Shear -92.04 KN
Cross-Section Dimensions
Height of Beam mm 300
Width of Beam mm 200
Length of Beam mm 1
Reinforcement data
Bottom Bars 1
First layer bars
Number of Reinforce Bars (1) 4
BAR (1) SIZE mm 16
Second layer bars
Number of Reinforce Bars (2) 0.001
BAR (2) SIZE mm 0.001
Top Bars
Number of Reinforce Bars (1) 2
BAR (1) SIZE mm 16
Weight if Bars kgs 0.70
Stirrup Size mm 10
Strength Reduction Factor 0.9
Steel Yield Strength MPA 275
Concrete Compressive Strength MPA 21
Concrete Cover mm 40
AREA OF ONE BAR (first layer) mm2 201.06
AREA OF ONE BAR (second layer) mm2 0
AREA OF ONE BAR (compression) mm2 201.06
Total Area of Compression Reinforcement Bars mm2 402.12
Total Area of Tensile Reinforcement Bars mm2 804.25
EFFECTIVE DEPTH OF BEAM mm 234.00
Tensile STEEL RATIO 0.0172
Compression STEEL RATIO 0.0086
MINIMUM STEEL RATIO 0.0051
Factor b1 0.850
Reinforcement ratio producing balanced strain condition 0.0378
MAXIMUM STEEL Reinforcement RATIO 0.0284
MAXIMUM STEEL Double Reinforcement RATIO 0.0370
Steel Reinforcement Ratio at Center of Gravity 0.0295
Compression Steel does not Yield
Ductility Test Beam is: Ductile
Shear Reinforcement
Page 1
BEAM6
face of support (mm) (KN) (KN) (KN) (mm) (mm)
50 to 234.00 10.92 42890.51 50556.78 0.20 CHECK SHEAR
234.00 0.17 0.03 -153.40 50567.68 0.00 CHECK SHEAR
0.17 500.17 76.40 91886.32 50491.30 0.43 CHECK SHEAR
500.17 rest at #VALUE! #VALUE! #VALUE! #VALUE! #VALUE!
rest at rest at #VALUE! #VALUE! #VALUE! #VALUE! #VALUE!
rest at rest at #VALUE! #VALUE! #VALUE! #VALUE! #VALUE!
Support
L/2
1@50mm
0 to d
#VALUE!
#VALUE!
follow table rest at Smax
Page 2
BEAM6
Ductile
Use
Page 3
BEAM6
(mm)
0.20
0.00
0.43
#VALUE!
#VALUE!
#VALUE!
Page 4
BEAM6A
Summary Results @ Midspan BEAM 6A
Bending Moment Capacity Mu = 83.17 KN-m
Moment Applied Moment Mz = 150.14 KN-m
Capacity Status FAIL
Shear -92.04 KN
Cross-Section Dimensions
Height of Beam mm 375
Width of Beam mm 150
Length of Beam mm 1
Reinforcement data
Bottom Bars 1
First layer bars
Number of Reinforce Bars (1) 3
BAR (1) SIZE mm 16
Second layer bars
Number of Reinforce Bars (2) 0.001
BAR (2) SIZE mm 0.001
Top Bars
Number of Reinforce Bars (1) 3
BAR (1) SIZE mm 16
Weight if Bars kgs 0.70
Stirrup Size mm 10
Strength Reduction Factor 0.9
Steel Yield Strength MPA 275
Concrete Compressive Strength MPA 21
Concrete Cover mm 40
AREA OF ONE BAR (first layer) mm2 201.06
AREA OF ONE BAR (second layer) mm2 0
AREA OF ONE BAR (compression) mm2 201.06
Total Area of Compression Reinforcement Bars mm2 603.19
Total Area of Tensile Reinforcement Bars mm2 603.19
EFFECTIVE DEPTH OF BEAM mm 309.00
Tensile STEEL RATIO 0.0130
Compression STEEL RATIO 0.0130
MINIMUM STEEL RATIO 0.0051
Factor b1 0.850
Reinforcement ratio producing balanced strain condition 0.0378
MAXIMUM STEEL Reinforcement RATIO 0.0284
MAXIMUM STEEL Double Reinforcement RATIO 0.0414
Steel Reinforcement Ratio at Center of Gravity 0.0288
Compression Steel does not Yield
Ductility Test Beam is: Ductile
Shear Reinforcement
Page 1
BEAM6A
face of support (mm) (KN) (KN) (KN) (mm) (mm)
50 to 309.00 8.11 56696.47 66801.90 0.20 CHECK SHEAR
309.00 0.17 0.02 -153.40 66809.99 0.00 CHECK SHEAR
0.17 500.17 57.30 91886.32 66752.71 0.32 CHECK SHEAR
500.17 rest at #VALUE! #VALUE! #VALUE! #VALUE! #VALUE!
rest at rest at #VALUE! #VALUE! #VALUE! #VALUE! #VALUE!
rest at rest at #VALUE! #VALUE! #VALUE! #VALUE! #VALUE!
Support
L/2
1@50mm
0 to d
#VALUE!
#VALUE!
follow table rest at Smax
Page 2
BEAM6A
Ductile
Use
Page 3
BEAM6A
(mm)
0.20
0.00
0.32
#VALUE!
#VALUE!
#VALUE!
Page 4
BEAM7
Summary Results Cantilever Beam BEAM 7
Bending Moment Capacity Mu = 0.00 KN-m
Moment Applied Moment Mz = 166.55 KN-m
Capacity Status FAIL
Shear -104.50 KN
Cross-Section Dimensions
Height of Cantilever Beam mm 0.001
Width of Cantilever Beam mm 0.001
Length of Cantilever Beam mm 1500
Reinforcement data
Bottom Bars 1
First layer bars
Number of Reinforce Bars (1) 0.001
BAR (1) SIZE mm 0.001
Second layer bars
Number of Reinforce Bars (2) 0.001
BAR (2) SIZE mm 0.001
Top Bars
Number of Reinforce Bars (1) 0.001
BAR (1) SIZE mm 0.001
Weight if Bars kgs 0.00
Stirrup Size mm 10
Strength Reduction Factor 0.9
Steel Yield Strength MPA 275
Concrete Compressive Strength MPA 21
Concrete Cover mm 40
AREA OF ONE BAR (first layer) mm2 0.00
AREA OF ONE BAR (second layer) mm2 0
AREA OF ONE BAR (compression) mm2 0.00
Total Area of Compression Reinforcement Bars mm2 0.00
Total Area of Tensile Reinforcement Bars mm2 0.00
EFFECTIVE DEPTH OF BEAM mm -50.00
Tensile STEEL RATIO 0.0000
Compression STEEL RATIO 0.0000
MINIMUM STEEL RATIO 0.0051
Factor b1 0.850
Reinforcement ratio producing balanced strain condition 0.0378
MAXIMUM STEEL Reinforcement RATIO 0.0284
MAXIMUM STEEL Double Reinforcement RATIO 0.0284
Steel Reinforcement Ratio at Center of Gravity -0.0815
Compression Steel Yields
Ductility Test Beam is: Ductile
Shear Reinforcement
Page 1
BEAM7
face of support (mm) (KN) (KN) (KN) (mm) (mm)
50 to -50.00 0.00 -215.97 131.14 -16.47 CHECK SHEAR
-50.00 250.00 0.00 -174.17 131.14 82.35 CHECK SHEAR
250.00 750.00 0.00 -104.50 131.14 247.05 CHECK SHEAR
750.00 rest at #VALUE! #VALUE! #VALUE! #VALUE! #VALUE!
rest at rest at #VALUE! #VALUE! #VALUE! #VALUE! #VALUE!
rest at rest at #VALUE! #VALUE! #VALUE! #VALUE! #VALUE!
Support
L/2
1@50mm
0 to d
#VALUE!
#VALUE!
follow table rest at Smax
Page 2
BEAM7
Ductile
Use
Page 3
BEAM7
(mm)
CHECK SHEAR
82.35
247.05
#VALUE!
#VALUE!
#VALUE!
Page 4
BEAM7A
Summary Results @ Midspan BEAM 7A
Bending Moment Capacity Mu = 179.24 KN-m
Moment Applied Moment Mz = 166.55 KN-m
Capacity Status PASS
Shear -104.50 KN
Cross-Section Dimensions
Height of Cantilever Beam mm 400
Width of Cantilever Beam mm 200
Length of Cantilever Beam mm 5010
Reinforcement data
Bottom Bars 2
First layer bars
Number of Reinforce Bars (1) 3
BAR (1) SIZE mm 16
Second layer bars
Number of Reinforce Bars (2) 2
BAR (2) SIZE mm 20
Top Bars
Number of Reinforce Bars (1) 5
BAR (1) SIZE mm 17.6
Weight if Bars kgs 7089.11
Stirrup Size mm 10
Strength Reduction Factor 0.9
Steel Yield Strength MPA 275
Concrete Compressive Strength MPA 21
Concrete Cover mm 40
AREA OF ONE BAR (first layer) mm2 201.06
AREA OF ONE BAR (second layer) mm2 314.16
AREA OF ONE BAR (compression) mm2 243.29
Total Area of Compression Reinforcement Bars mm2 1216.43
Total Area of Tensile Reinforcement Bars mm2 1231.51
EFFECTIVE DEPTH OF BEAM mm 334.00
Tensile STEEL RATIO 0.0184
Compression STEEL RATIO 0.0182
MINIMUM STEEL RATIO 0.0051
Factor b1 0.850
Reinforcement ratio producing balanced strain condition 0.0378
MAXIMUM STEEL Reinforcement RATIO 0.0284
MAXIMUM STEEL Double Reinforcement RATIO 0.0466
Steel Reinforcement Ratio at Center of Gravity 0.0331
Compression Steel does not Yield
Ductility Test Beam is: Ductile
Shear Reinforcement
Page 1
BEAM7A
face of support (mm) (KN) (KN) (KN) (mm) (mm)
50 to 334.00 15.59 -195.07 122.14 118.13 83.50
334.00 835.00 127.55 -174.17 234.10 154.08 CHECK SHEAR
835.00 1335.00 203.92 -153.31 310.47 185.74 CHECK SHEAR
1335.00 1835.00 280.30 -132.45 386.85 204.90 CHECK SHEAR
1835.00 2335.00 356.68 -111.59 463.23 217.74 CHECK SHEAR
2335.00 2835.00 433.05 -90.73 539.60 226.95 CHECK SHEAR
Support
L/2
1@50mm
0 to d
d to1835
1835 to 2335
follow table rest at Smax
Page 2
BEAM7A
Ductile
Use
Page 3
BEAM7A
(mm)
83.50
154.08
185.74
204.90
217.74
226.95
Page 4
BEAM8
Summary Results @ Midspan BEAM 8
Bending Moment Capacity Mu = -716987.87 KN-m
Moment Applied Moment Mz = 22.18 KN-m
Capacity Status FAIL
Shear -14.27 KN
Cross-Section Dimensions
Height of Cantilever Beam mm 0.001
Width of Cantilever Beam mm 0.001
Length of Cantilever Beam mm 1
Reinforcement data
Bottom Bars 1
First layer bars
Number of Reinforce Bars (1) 3
BAR (1) SIZE mm 16
Second layer bars
Number of Reinforce Bars (2) 0.001
BAR (2) SIZE mm 0.001
Top Bars
Number of Reinforce Bars (1) 5
BAR (1) SIZE mm 17.6
Weight if Bars kgs 1.05
Stirrup Size mm 10
Strength Reduction Factor 0.9
Steel Yield Strength MPA 275
Concrete Compressive Strength MPA 21
Concrete Cover mm 40
AREA OF ONE BAR (first layer) mm2 201.06
AREA OF ONE BAR (second layer) mm2 0
AREA OF ONE BAR (compression) mm2 243.29
Total Area of Compression Reinforcement Bars mm2 1216.43
Total Area of Tensile Reinforcement Bars mm2 603.19
EFFECTIVE DEPTH OF BEAM mm -66.00
Tensile STEEL RATIO -9139.3385
Compression STEEL RATIO -18430.9993
MINIMUM STEEL RATIO 0.0051
Factor b1 0.850
Reinforcement ratio producing balanced strain condition 0.0378
MAXIMUM STEEL Reinforcement RATIO 0.0284
MAXIMUM STEEL Double Reinforcement RATIO -18430.9709
Steel Reinforcement Ratio at Center of Gravity -18431.0746
Compression Steel Yields
Ductility Test Beam is: Ductile
Shear Reinforcement
Page 1
BEAM8
face of support (mm) (KN) (KN) (KN) (mm) (mm)
50 to -66.00 0.00 -1912.05 2232.69 -1.28 CHECK SHEAR
-66.00 0.17 0.00 -23.78 2232.69 0.00 CHECK SHEAR
0.17 500.17 0.00 14245.48 2232.69 9.68 CHECK SHEAR
500.17 rest at #VALUE! #VALUE! #VALUE! #VALUE! #VALUE!
rest at rest at #VALUE! #VALUE! #VALUE! #VALUE! #VALUE!
rest at rest at #VALUE! #VALUE! #VALUE! #VALUE! #VALUE!
Support
L/2
1@50mm
0 to d
#VALUE!
#VALUE!
follow table rest at Smax
Page 2
BEAM8
Ductile
Use
Page 3
BEAM8
(mm)
CHECK SHEAR
0.00
9.68
#VALUE!
#VALUE!
#VALUE!
Page 4
BEAM9
Summary Results @ Midspan BEAM 9
Bending Moment Capacity Mu = 0.00 KN-m
Moment Applied Moment Mz = 22.18 KN-m
Capacity Status FAIL
Shear -14.27 KN
Cross-Section Dimensions
Height of Cantilever Beam mm 0.001
Width of Cantilever Beam mm 0.001
Length of Cantilever Beam mm 1
Reinforcement data
Bottom Bars 1
First layer bars
Number of Reinforce Bars (1) 0.001
BAR (1) SIZE mm 0.001
Second layer bars
Number of Reinforce Bars (2) 0.001
BAR (2) SIZE mm 0.001
Top Bars
Number of Reinforce Bars (1) 0.001
BAR (1) SIZE mm 0.001
Weight if Bars kgs 0.00
Stirrup Size mm 10
Strength Reduction Factor 0.9
Steel Yield Strength MPA 275
Concrete Compressive Strength MPA 21
Concrete Cover mm 40
AREA OF ONE BAR (first layer) mm2 0.00
AREA OF ONE BAR (second layer) mm2 0
AREA OF ONE BAR (compression) mm2 0.00
Total Area of Compression Reinforcement Bars mm2 0.00
Total Area of Tensile Reinforcement Bars mm2 0.00
EFFECTIVE DEPTH OF BEAM mm -50.00
Tensile STEEL RATIO 0.0000
Compression STEEL RATIO 0.0000
MINIMUM STEEL RATIO 0.0051
Factor b1 0.850
Reinforcement ratio producing balanced strain condition 0.0378
MAXIMUM STEEL Reinforcement RATIO 0.0284
MAXIMUM STEEL Double Reinforcement RATIO 0.0284
Steel Reinforcement Ratio at Center of Gravity -0.0815
Compression Steel Yields
Ductility Test Beam is: Ductile
Shear Reinforcement
Page 1
BEAM9
face of support (mm) (KN) (KN) (KN) (mm) (mm)
50 to -50.00 0.00 -1455.46 1695.52 -1.27 CHECK SHEAR
-50.00 0.17 0.00 -23.78 1695.52 0.00 CHECK SHEAR
0.17 500.17 0.00 14245.48 1695.52 12.74 CHECK SHEAR
500.17 rest at #VALUE! #VALUE! #VALUE! #VALUE! #VALUE!
rest at rest at #VALUE! #VALUE! #VALUE! #VALUE! #VALUE!
rest at rest at #VALUE! #VALUE! #VALUE! #VALUE! #VALUE!
Support
L/2
1@50mm
0 to d
#VALUE!
#VALUE!
follow table rest at Smax
Page 2
BEAM9
Ductile
Use
Page 3
BEAM9
(mm)
CHECK SHEAR
0.00
12.74
#VALUE!
#VALUE!
#VALUE!
Page 4
BEAM10
Summary Results @ Midspan BEAM 10
Bending Moment Capacity Mu = 0.00 KN-m
Moment Applied Moment Mz = 22.18 KN-m
Capacity Status FAIL
Shear -14.27 KN
Cross-Section Dimensions
Height of Cantilever Beam mm 0.001
Width of Cantilever Beam mm 0.001
Length of Cantilever Beam mm 1
Reinforcement data
Bottom Bars 1
First layer bars
Number of Reinforce Bars (1) 0.001
BAR (1) SIZE mm 0.001
Second layer bars
Number of Reinforce Bars (2) 0.001
BAR (2) SIZE mm 0.001
Top Bars
Number of Reinforce Bars (1) 0.001
BAR (1) SIZE mm 0.001
Weight if Bars kgs 0.00
Stirrup Size mm 10
Strength Reduction Factor 0.9
Steel Yield Strength MPA 275
Concrete Compressive Strength MPA 21
Concrete Cover mm 40
AREA OF ONE BAR (first layer) mm2 0.00
AREA OF ONE BAR (second layer) mm2 0
AREA OF ONE BAR (compression) mm2 0.00
Total Area of Compression Reinforcement Bars mm2 0.00
Total Area of Tensile Reinforcement Bars mm2 0.00
EFFECTIVE DEPTH OF BEAM mm -50.00
Tensile STEEL RATIO 0.0000
Compression STEEL RATIO 0.0000
MINIMUM STEEL RATIO 0.0051
Factor b1 0.850
Reinforcement ratio producing balanced strain condition 0.0378
MAXIMUM STEEL Reinforcement RATIO 0.0284
MAXIMUM STEEL Double Reinforcement RATIO 0.0284
Steel Reinforcement Ratio at Center of Gravity -0.0815
Compression Steel Yields
Ductility Test Beam is: Ductile
Shear Reinforcement
Page 1
BEAM10
face of support (mm) (KN) (KN) (KN) (mm) (mm)
50 to -50.00 0.00 -1455.46 1695.52 -1.27 CHECK SHEAR
-50.00 0.17 0.00 -23.78 1695.52 0.00 CHECK SHEAR
0.17 500.17 0.00 14245.48 1695.52 12.74 CHECK SHEAR
500.17 rest at #VALUE! #VALUE! #VALUE! #VALUE! #VALUE!
rest at rest at #VALUE! #VALUE! #VALUE! #VALUE! #VALUE!
rest at rest at #VALUE! #VALUE! #VALUE! #VALUE! #VALUE!
Support
L/2
1@50mm
0 to d
#VALUE!
#VALUE!
follow table rest at Smax
Page 2
BEAM10
Ductile
Use
Page 3
BEAM10
(mm)
CHECK SHEAR
0.00
12.74
#VALUE!
#VALUE!
#VALUE!
Page 4
BEAM11
Summary Results @ Midspan BEAM 11
Bending Moment Capacity Mu = 0.00 KN-m
Moment Applied Moment Mz = 22.18 KN-m
Capacity Status FAIL
Shear -14.27 KN
Cross-Section Dimensions
Height of Cantilever Beam mm 0.001
Width of Cantilever Beam mm 0.001
Length of Cantilever Beam mm 1
Reinforcement data
Bottom Bars 1
First layer bars
Number of Reinforce Bars (1) 0.001
BAR (1) SIZE mm 0.001
Second layer bars
Number of Reinforce Bars (2) 0.001
BAR (2) SIZE mm 0.001
Top Bars
Number of Reinforce Bars (1) 0.001
BAR (1) SIZE mm 0.001
Weight if Bars kgs 0.00
Stirrup Size mm 10
Strength Reduction Factor 0.9
Steel Yield Strength MPA 275
Concrete Compressive Strength MPA 21
Concrete Cover mm 40
AREA OF ONE BAR (first layer) mm2 0.00
AREA OF ONE BAR (second layer) mm2 0
AREA OF ONE BAR (compression) mm2 0.00
Total Area of Compression Reinforcement Bars mm2 0.00
Total Area of Tensile Reinforcement Bars mm2 0.00
EFFECTIVE DEPTH OF BEAM mm -50.00
Tensile STEEL RATIO 0.0000
Compression STEEL RATIO 0.0000
MINIMUM STEEL RATIO 0.0051
Factor b1 0.850
Reinforcement ratio producing balanced strain condition 0.0378
1 MAXIMUM STEEL Reinforcement RATIO 0.0284
MAXIMUM STEEL Double Reinforcement RATIO 0.0284
Steel Reinforcement Ratio at Center of Gravity -0.0815
Compression Steel Yields
Ductility Test Beam is: Ductile
Shear Reinforcement
Page 1
BEAM11
face of support (mm) (KN) (KN) (KN) (mm) (mm)
50 to -50.00 0.00 -1455.46 1695.52 -1.27 CHECK SHEAR
-50.00 0.17 0.00 -23.78 1695.52 0.00 CHECK SHEAR
0.17 500.17 0.00 14245.48 1695.52 12.74 CHECK SHEAR
500.17 rest at #VALUE! #VALUE! #VALUE! #VALUE! #VALUE!
rest at rest at #VALUE! #VALUE! #VALUE! #VALUE! #VALUE!
rest at rest at #VALUE! #VALUE! #VALUE! #VALUE! #VALUE!
Support
L/2
1@50mm
0 to d
#VALUE!
#VALUE!
follow table rest at Smax
Page 2
BEAM11
Ductile
Use
Page 3
BEAM11
(mm)
CHECK SHEAR
0.00
12.74
#VALUE!
#VALUE!
#VALUE!
Page 4
BEAM12
Summary Results Cantilever Beam BEAM 12
Bending Moment Capacity Mu = 0.00 KN-m
Moment Applied Moment Mz = 22.18 KN-m
Capacity Status FAIL
Shear -14.27 KN
Cross-Section Dimensions
Height of Cantilever Beam mm 0.001
Width of Cantilever Beam mm 0.001
Length of Cantilever Beam mm 1
Reinforcement data
Bottom Bars 1
First layer bars
Number of Reinforce Bars (1) 0.001
BAR (1) SIZE mm 0.001
Second layer bars
Number of Reinforce Bars (2) 0.001
BAR (2) SIZE mm 0.001
Top Bars
Number of Reinforce Bars (1) 0.001
BAR (1) SIZE mm 0.001
Weight if Bars kgs 0.00
Stirrup Size mm 10
Strength Reduction Factor 0.9
Steel Yield Strength MPA 275
Concrete Compressive Strength MPA 21
Concrete Cover mm 40
AREA OF ONE BAR (first layer) mm2 0.00
AREA OF ONE BAR (second layer) mm2 0
AREA OF ONE BAR (compression) mm2 0.00
Total Area of Compression Reinforcement Bars mm2 0.00
Total Area of Tensile Reinforcement Bars mm2 0.00
EFFECTIVE DEPTH OF BEAM mm -50.00
Tensile STEEL RATIO 0.0000
Compression STEEL RATIO 0.0000
MINIMUM STEEL RATIO 0.0051
Factor b1 0.850
Reinforcement ratio producing balanced strain condition 0.0378
1 MAXIMUM STEEL Reinforcement RATIO 0.0284
MAXIMUM STEEL Double Reinforcement RATIO 0.0284
Steel Reinforcement Ratio at Center of Gravity -0.0815
Compression Steel Yields
Ductility Test Beam is: Ductile
Shear Reinforcement
Page 1
BEAM12
face of support (mm) (KN) (KN) (KN) (mm) (mm)
50 to -50.00 0.00 -1455.46 1695.52 -1.27 CHECK SHEAR
-50.00 0.17 0.00 -23.78 1695.52 0.00 CHECK SHEAR
0.17 500.17 0.00 14245.48 1695.52 12.74 CHECK SHEAR
500.17 rest at #VALUE! #VALUE! #VALUE! #VALUE! #VALUE!
rest at rest at #VALUE! #VALUE! #VALUE! #VALUE! #VALUE!
rest at rest at #VALUE! #VALUE! #VALUE! #VALUE! #VALUE!
Support
L/2
1@50mm
0 to d
#VALUE!
#VALUE!
follow table rest at Smax
Page 2
BEAM12
Ductile
Use
Page 3
BEAM12
(mm)
CHECK SHEAR
0.00
12.74
#VALUE!
#VALUE!
#VALUE!
Page 4
BEAM13
Summary Results Cantilever Beam BEAM 13
Bending Moment Capacity Mu = 0.00 KN-m
Moment Applied Moment Mz = 22.18 KN-m
Capacity Status FAIL
Shear -14.27 KN
Cross-Section Dimensions
Height of Cantilever Beam mm 0.001
Width of Cantilever Beam mm 0.001
Length of Cantilever Beam mm 1
Reinforcement data
Bottom Bars 1
First layer bars
Number of Reinforce Bars (1) 0.001
BAR (1) SIZE mm 0.001
Second layer bars
Number of Reinforce Bars (2) 0.001
BAR (2) SIZE mm 0.001
Top Bars
Number of Reinforce Bars (1) 0.001
BAR (1) SIZE mm 0.001
Weight if Bars kgs 0.00
Stirrup Size mm 10
Strength Reduction Factor 0.9
Steel Yield Strength MPA 275
Concrete Compressive Strength MPA 21
Concrete Cover mm 40
AREA OF ONE BAR (first layer) mm2 0.00
AREA OF ONE BAR (second layer) mm2 0
AREA OF ONE BAR (compression) mm2 0.00
Total Area of Compression Reinforcement Bars mm2 0.00
Total Area of Tensile Reinforcement Bars mm2 0.00
EFFECTIVE DEPTH OF BEAM mm -50.00
Tensile STEEL RATIO 0.0000
Compression STEEL RATIO 0.0000
MINIMUM STEEL RATIO 0.0051
Factor b1 0.850
Reinforcement ratio producing balanced strain condition 0.0378
MAXIMUM STEEL Reinforcement RATIO 0.0284
MAXIMUM STEEL Double Reinforcement RATIO 0.0284
Steel Reinforcement Ratio at Center of Gravity -0.0815
Compression Steel Yields
Ductility Test Beam is: Ductile
Shear Reinforcement
Page 1
BEAM13
face of support (mm) (KN) (KN) (KN) (mm) (mm)
50 to -50.00 0.00 -1455.46 1695.52 -1.27 CHECK SHEAR
-50.00 0.17 0.00 -23.78 1695.52 0.00 CHECK SHEAR
0.17 500.17 0.00 14245.48 1695.52 12.74 CHECK SHEAR
500.17 rest at #VALUE! #VALUE! #VALUE! #VALUE! #VALUE!
rest at rest at #VALUE! #VALUE! #VALUE! #VALUE! #VALUE!
rest at rest at #VALUE! #VALUE! #VALUE! #VALUE! #VALUE!
Support
L/2
1@50mm
0 to d
#VALUE!
#VALUE!
follow table rest at Smax
Page 2
BEAM13
Ductile
Use
Page 3
BEAM13
(mm)
CHECK SHEAR
0.00
12.74
#VALUE!
#VALUE!
#VALUE!
Page 4
BEAM14
Summary Results @ Midspan BEAM 14
Bending Moment Capacity Mu = 0.00 KN-m
Moment Applied Moment Mz = 22.18 KN-m
Capacity Status FAIL
Shear -14.27 KN
Cross-Section Dimensions
Height of Cantilever Beam mm 0.001
Width of Cantilever Beam mm 0.001
Length of Cantilever Beam mm 1
Reinforcement data
Bottom Bars 1
First layer bars
Number of Reinforce Bars (1) 0.001
BAR (1) SIZE mm 0.001
Second layer bars
Number of Reinforce Bars (2) 0.001
BAR (2) SIZE mm 0.001
Top Bars
Number of Reinforce Bars (1) 0.001
BAR (1) SIZE mm 0.001
Weight if Bars kgs 0.00
Stirrup Size mm 10
Strength Reduction Factor 0.9
Steel Yield Strength MPA 275
Concrete Compressive Strength MPA 21
Concrete Cover mm 40
AREA OF ONE BAR (first layer) mm2 0.00
AREA OF ONE BAR (second layer) mm2 0
AREA OF ONE BAR (compression) mm2 0.00
Total Area of Compression Reinforcement Bars mm2 0.00
Total Area of Tensile Reinforcement Bars mm2 0.00
EFFECTIVE DEPTH OF BEAM mm -50.00
Tensile STEEL RATIO 0.0000
Compression STEEL RATIO 0.0000
MINIMUM STEEL RATIO 0.0051
Factor b1 0.850
Reinforcement ratio producing balanced strain condition 0.0378
MAXIMUM STEEL Reinforcement RATIO 0.0284
MAXIMUM STEEL Double Reinforcement RATIO 0.0284
Steel Reinforcement Ratio at Center of Gravity -0.0815
Compression Steel Yields
Ductility Test Beam is: Ductile
Shear Reinforcement
Page 1
BEAM14
face of support (mm) (KN) (KN) (KN) (mm) (mm)
50 to -50.00 0.00 -1455.46 1695.52 -1.27 CHECK SHEAR
-50.00 0.17 0.00 -23.78 1695.52 0.00 CHECK SHEAR
0.17 500.17 0.00 14245.48 1695.52 12.74 CHECK SHEAR
500.17 rest at #VALUE! #VALUE! #VALUE! #VALUE! #VALUE!
rest at rest at #VALUE! #VALUE! #VALUE! #VALUE! #VALUE!
rest at rest at #VALUE! #VALUE! #VALUE! #VALUE! #VALUE!
Support
L/2
1@50mm
0 to d
#VALUE!
#VALUE!
follow table rest at Smax
Page 2
BEAM14
Ductile
Use
Page 3
BEAM14
(mm)
CHECK SHEAR
0.00
12.74
#VALUE!
#VALUE!
#VALUE!
Page 4
BEAM15
Summary Results @ Midspan BEAM 15
Bending Moment Capacity Mu = -308295.37 KN-m
Moment Applied Moment Mz = 22.18 KN-m
Capacity Status FAIL
Shear -14.27 KN
Cross-Section Dimensions
Height of Cantilever Beam mm 0.001
Width of Cantilever Beam mm 0.001
Length of Cantilever Beam mm 1
Reinforcement data
Bottom Bars 1
First layer bars
Number of Reinforce Bars (1) 2
BAR (1) SIZE mm 16
Second layer bars
Number of Reinforce Bars (2) 0.001
BAR (2) SIZE mm 0.001
Top Bars
Number of Reinforce Bars (1) 0.001
BAR (1) SIZE mm 0.001
Weight if Bars kgs 0.23
Stirrup Size mm 10
Strength Reduction Factor 0.9
Steel Yield Strength MPA 275
Concrete Compressive Strength MPA 21
Concrete Cover mm 40
AREA OF ONE BAR (first layer) mm2 201.06
AREA OF ONE BAR (second layer) mm2 0
AREA OF ONE BAR (compression) mm2 0.00
Total Area of Compression Reinforcement Bars mm2 0.00
Total Area of Tensile Reinforcement Bars mm2 402.12
EFFECTIVE DEPTH OF BEAM mm -66.00
Tensile STEEL RATIO -6092.8923
Compression STEEL RATIO 0.0000
MINIMUM STEEL RATIO 0.0051
Factor b1 0.850
Reinforcement ratio producing balanced strain condition 0.0378
MAXIMUM STEEL Reinforcement RATIO 0.0284
MAXIMUM STEEL Double Reinforcement RATIO 0.0284
Steel Reinforcement Ratio at Center of Gravity -0.0617
Compression Steel does not Yield
Ductility Test Beam is: Ductile
Shear Reinforcement
Page 1
BEAM15
face of support (mm) (KN) (KN) (KN) (mm) (mm)
50 to -66.00 0.00 -1912.05 2232.69 -1.28 CHECK SHEAR
-66.00 0.17 0.00 -23.78 2232.69 0.00 CHECK SHEAR
0.17 500.17 0.00 14245.48 2232.69 9.68 CHECK SHEAR
500.17 rest at #VALUE! #VALUE! #VALUE! #VALUE! #VALUE!
rest at rest at #VALUE! #VALUE! #VALUE! #VALUE! #VALUE!
rest at rest at #VALUE! #VALUE! #VALUE! #VALUE! #VALUE!
Support
L/2
1@50mm
0 to d
#VALUE!
#VALUE!
follow table rest at Smax
Page 2
BEAM15
Ductile
Use
Page 3
BEAM15
(mm)
CHECK SHEAR
0.00
9.68
#VALUE!
#VALUE!
#VALUE!
Page 4
COLUMN1
DESIGN OF BOTTOM INNER COLUMNS
Summary Results
Applied Moment Mu max = 40.12 KN-m RESULTS
Applied Axial Load Pumax = 364.11 KN Ductile
Nominal Load 520.16 KN SLENDER
Pass 640.81 KN
Additional Reaction Mu= 0.00 KN-m
Pu= 0.00 KN
Cross-Section Dimensions
Height of Beam critical axis H= 300 mm X
Base of Beam B= 200 mm
Other Datas
Concrete Cover 70 mm
Bar Type Fc' = 21 Mpa
Fy = 275 Mpa
e= 110.19 mm
Bars Bar Pcs stirrups = 10 mm
16 4 corner mm
12 4 in between
As = 515.2224 mm2
As2 = 226.1952 mm2
x1 = 80 mm
x2 = 160 mm
x3 = 230 mm
x4 = 150 mm
Assuming As'=As Weight= 5.70 kgs
Assuming that Comp. And Tensile steel yields 0.06 KN
ΣFH=0 ; Pn+T = C + C'
Equation 1
Pn = 0.85fc'aB + As'fy - Asfy
ΣM@ the Tensile Steel
Equation 2
Pn (e+x1) = As'fyx2 + 0.85fc'aB (x3 – (a/2)) + As2fyx3
Equating 1 and 2
a2 a
1785 + -142126.361 + -32000337.6
By Quadratic Formula
x = (-b (+/-) √ b^2 - 4 ac ) / 2a
Page 1
COLUMN1
Axis
Status
Column is
SLENDER
Page 2
COLUMN2
DESIGN OF BOTTOM OUTER COLUMNS
Summary Results
Applied Moment Mu max = 150.14 KN-m RESULTS
Applied Axial Load Pumax = 1164.92 KN Ductile
Nominal Load 1664.17 KN 0
Fail 982.11 KN
Additional Reaction Mu= 0.00 KN-m
Pu= 0.00 KN
Cross-Section Dimensions
Height of Beam critical axis H= 400 mm X
Base of Beam B= 200 mm
Other Datas
Concrete Cover 70 mm
Bar Type Fc' = 21 Mpa
Fy = 275 Mpa
e= 128.88 mm
Bars Bar Pcs stirrups = 10 mm
16 4 corner mm
16 4 in between
As = 603.1872 mm2
As2 = 402.1248 mm2
x1 = 130 mm
x2 = 260 mm
x3 = 330 mm
x4 = 200 mm
Assuming As'=As Weight= 6.68 kgs
Assuming that Comp. And Tensile steel yields 0.07 KN
ΣFH=0 ; Pn+T = C + C'
Equation 1
Pn = 0.85fc'aB + As'fy - Asfy
ΣM@ the Tensile Steel
Equation 2
Pn (e+x1) = As'fyx2 + 0.85fc'aB (x3 – (a/2)) + As2fyx3
Equating 1 and 2
a2 a
1785 + -253885.295 + -65244748.8
By Quadratic Formula
x = (-b (+/-) √ b^2 - 4 ac ) / 2a
Page 1
COLUMN2
X-AXIS 3000 F F N 1.2 3600 Lex/h = 9.00
Y-AXIS 3000 F F N 1.2 3600 Ley/b = 18.00
Page 2
COLUMN2
Axis
Status
Page 3
COLUMN2
Column is
SLENDER
Page 4
COLUMN3
DESIGN OF BOTTOM CORNER COLUMNS
Summary Results
Applied Moment Mu max = 5.77 KN-m RESULTS
Applied Axial Load Pumax = 1.89 KN Ductile
Nominal Load 2.70 KN 0
Fail 0.00 KN
Additional Reaction Mu= 0.00 KN-m
Pu= 0.00 KN
Cross-Section Dimensions
Height of Beam critical axis H= 0.001 mm X
Base of Beam B= 0.001 mm
Other Datas
Concrete Cover 70 mm
Bar Type Fc' = 21 Mpa
Fy = 275 Mpa
e= 3057.31 mm
Bars Bar Pcs stirrups = 10 mm
16 4 corner mm
12 4 in between
As = 515.2224 mm2
As2 = 226.1952 mm2
x1 = -69.9995 mm
x2 = -139.999 mm
x3 = -69.999 mm
x4 = 0.0005 mm
Assuming As'=As Weight= 5.70 kgs
Assuming that Comp. And Tensile steel yields 0.06 KN
ΣFH=0 ; Pn+T = C + C'
Equation 1
Pn = 0.85fc'aB + As'fy - Asfy
ΣM@ the Tensile Steel
Equation 2
Pn (e+x1) = As'fyx2 + 0.85fc'aB (x3 – (a/2)) + As2fyx3
Equating 1 and 2
a2 a
0.008925 + 54.5729745 + 19835889.612
By Quadratic Formula
x = (-b (+/-) √ b^2 - 4 ac ) / 2a
Page 1
COLUMN3
Axis
Status
Column is
FAILS
Page 2
INNER SQUARE FOOTING
RC ISOLATED COLUMN FOOTING
Inner Footing
d
Edge 1
L
X
Summary Results
Pu 147.45 kN
Dimension
Footing Dimension L 1000 mm
W 1000 mm
Assumed Thickness t 250.00 mm
Assumed Depth d 164.00 mm
Soil Pressure 147.45 KN/m2
Allowable Soil Pressure 150.0 KN/m2
ok
Strength Reduction Factor 0.70
Bar Yield Strength 275 MPA
Concrete Compressive Strength 21.0 MPA
Concrete Cover 70.0 mm
Column Details
Column Dimension along Length 300 mm
Column Dimension along Width 200 mm
Column Distance from Edge1 500.00 mm
Depth required for One-Way Shear 42.24
Depth required for Punching Shear 56.99 mm
use d 164.00 mm
SHEAR AND MOMENT DIAGRAM
Page 1
INNER SQUARE FOOTING
Page 2
OUTER SQUARE FOOTING
RC ISOLATED COLUMN FOOTING
Outer Footing
d
Edge 1
L
X
Summary Results
Pu 619.63 kN
Dimension
Footing Dimension L 1300 mm
W 1300 mm
Assumed Thickness t 300.00 mm
Assumed Depth d 214.00 mm
Soil Pressure 366.64 KN/m2
Allowable Soil Pressure 150.0 KN/m2
change dimension
Strength Reduction Factor 0.70
Bar Yield Strength 275 MPA
Concrete Compressive Strength 21.0 MPA
Concrete Cover 70.0 mm
Column Details
Column Dimension along Length 400 mm
Column Dimension along Width 200 mm
Column Distance from Edge1 650.00 mm
Depth required for One-Way Shear 133.28
Depth required for Punching Shear 197.20 mm
use d 214.00 mm
SHEAR AND MOMENT DIAGRAM
Page 1
Page 2
CORNER SQUARE FOOTING
RC ISOLATED COLUMN FOOTING
Corner Footing
Edge 1
L
X
Summary Results
Pu 0.01 kN
Dimension
Footing Dimension L 0.001 mm
W 0.001 mm
Assumed Thickness t 300.00 mm
Assumed Depth d 214.00 mm
Soil Pressure 6647990378.15 KN/m2
Allowable Soil Pressure 150.0 KN/m2
change dimension
Strength Reduction Factor 0.70
Bar Yield Strength 275 MPA
Concrete Compressive Strength 21.0 MPA
Concrete Cover 70.0 mm
Column Details
Column Dimension along Length 0.001 mm
Column Dimension along Width 0.001 mm
Column Distance from Edge1 0.00 mm
Depth required for One-Way Shear -2191426115.37
Depth required for Punching Shear -150357585.88 mm
use d 214.00 mm
SHEAR AND MOMENT DIAGRAM
Page 1
Page 2
SUMMARY
BEAM BASE HEIGHT BARS AT MIDSPAN
(mm) (mm) BOTTOM NUMBER 2ND LAYER
1 350.00 400.00 16.0 5.0 16.0
2 200.00 400.00 16.0 3.0 0.0
3 200.00 400.00 16.0 3.0 0.0
4 190.00 375.00 16.0 3.0 0.0
5 200.00 300.00 0.0 0.0 0.0
5A 200.00 400.00 16.0 3.0 20.0
6 200.00 300.00 16.0 4.0 0.0
6A 150.00 375.00 16.0 3.0 0.0
7 0.00 0.00 0.0 0.0 0.0
7A 200.00 400.00 16.0 3.0 20.0
8 0.00 0.00 16.0 3.0 0.0
9 0.00 0.00 0.0 0.0 0.0
10 0.00 0.00 0.0 0.0 0.0
11 0.00 0.00 0.0 0.0 0.0
12 0.00 0.00 0.0 0.0 0.0
13 0.00 0.00 0.0 0.0 0.0
14 0.00 0.00 0.0 0.0 0.0
15 0.00 0.00 16.0 2.0 0.0
Page 1
SUMMARY
BARS AT MIDSPAN MAX MOMENT MAX SHEAR
NUMBER TOP NUMBER (Kn-m) (Kn)
2.0 16.0 3.0 120.55 -96.39
0.0 16.0 3.0 78.22 -64.47
0.0 16.0 3.0 44.63 -35.29
0.0 16.0 3.0 40.12 -21.48
0.0 0.0 0.0 164.53 -107.60
2.0 17.6 5.0 166.55 -104.50
0.0 16.0 2.0 20.00 -92.04
0.0 16.0 3.0 150.14 -92.04
0.0 0.0 0.0 166.55 -104.50
2.0 17.6 5.0 166.55 -104.50
0.0 17.6 5.0 22.18 -14.27
0.0 0.0 0.0 22.18 -14.27
0.0 0.0 0.0 22.18 -14.27
0.0 0.0 0.0 22.18 -14.27
0.0 0.0 0.0 22.18 -14.27
0.0 0.0 0.0 22.18 -14.27
0.0 0.0 0.0 22.18 -14.27
0.0 0.0 0.0 22.18 -14.27
TIES PU MU
NUMBER (mm) (Kn) (Kn)
4.0 200 364.11 40.12
4.0 200 1164.92 150.14
4.0 0.001 1.89 5.77
Page 2