Professional Documents
Culture Documents
Cost
Cost
Submission price on 11 Ma
Appointed PE fee
Processing fee
Insurance
All structural sections except hollow sections shall be hot rolled steel of grade s355 steel conforming to B.S. EN 100
B.S. 4-1 & B.S. EN 10056 unless otherwise stated.
Unless otherwise stated, all structural steel shall be hot dipped galvanised to
80 microns and two coats of compatible zinc-rich paint shall be applied to exposed steel surfaces
Bolts
All butt welded joints shall be tested, especially for key structural members.
Painting work
All structural steel delivered to site must be prepared against corrosion
with 1 coat of priner and 2 coats of epoxy paint/ PU paint subjected to
Architect/ Structural QP's selection/approval
Structural drawings
M&E works
Fire Protection
Drain-off water and recharge water for the affected fire sprinkler system
Fire drawings
Lighting
LED light fittings for the extended part of canopy c/w new wiring, conduits, truking and termination to existing DB
LED light fittings shall match with existing light fittings (recessed downlight) type in the canopy
both canopies shall be connected to existing lighting DB's,
DB-01-LP1 & LP2 respectively
Provisions shall be made for additional breakers if there no sufficient spare
breakers at existing lighting DB's.
Lighting drawings
LEW services - Endorsed as built drawings, supervision and turn on power supply
Earth pit and bond to steel structure affested by canopy extension (include excavation)
Lightning drawings
Architectural requirements
Metal roofing system from a single manufacturee have a proven track record and relevant ISO 9000 certification
(Aluminium profiled roofing)
(Movements, dead loads, live loads, deflections, weather and water resistance, wind pressure,
fire safety, testing, deviation from lines, planes and verticallity shall be limited to long wave formations of averag
2mm for every 1000mm run, with maximum amplitude of 3mm at any single point.
Shall include all other aluminium extrusions, including tolerance clips, gable and clips,
channels, drip angles, zed spacers and any other components necessary for total roofing system
Extruded profiles shall be aluminium alloy to 6061-T6 or 6063-T5.
Seal all penetration with an appropriate proprietary pipe sleeve flashing for water-
tightness as recommended by the manufacturer
match the existing canopy at loading/ unloading bay in terms of color and finish, so Provide a seamless connection
in addition, the protective coating shall meet the requirements of SS 631
Bracings to be added to the supporting frame around all openings and penetrations
e.g. skylights, M7E services, etc.
All accessories e.g, ridge capping, flashing, pipe sleeves, clamps, purlins, insulation,etc., necessary for a complete m
$ 48,316.20 $ 48,300.00
1 lot $ 1,000.00
13 nos. $ 180.00
1 lot $ 800.00
1 lot $ 1,000.00
1 lot $ 1,500.00
1 lot
1 lot
1 lot
1 lot
2 lot $ 2,000.00
1 lot
1 lot $ 720.00
1 lot
de a seamless connection
90%
85%
$ 994.31
$ 10,000.00
$ 7,500.00
$ 2,000.00
$ 2,000.00
$ 15,000.00
$ 2,000.00
$ 500.00
$ 3,000.00
$ 2,500.00
$ 1,000.00
$ 2,340.00
$ 800.00
$ 1,000.00
$ 1,500.00
Included
$ 1,500.00
$ 1,800.00
$ 1,500.00
$ 2,000.00
$ 1,000.00
$ 4,000.00
$ 2,000.00
$ 720.00
$ 1,000.00
$ 19,309.84
$ 3,000.00
$ 1,500.00
$ 90,469.84 $ 1,171.29
$ 81,422.86 $ 1,054.16
$ 76,899.37 $ 995.60