Professional Documents
Culture Documents
See notes !
Finish Black Galv. Black Galv. Black Black Black Galv. Black Black Galv. Black
Material, DIN St 37.0 St 33 St 37.0 St 37.0 St 33.2 St 33 St 33 St 33 St 37.0 St 37.0 St 37.0 St 33.2
2) 3) 4)
Valid code 2140 2141 2142 2112 2144 2130 2133 2131 2132 2110 2111 2134
P235TR1 P195TR1 P195GH P195GH
Material, EN P235TR2 1.0255 5) P195TR1 1.0107 P235TR2 1.0255 5)
1.0254 1.0107 1.0348 1.0348
o
Design temp. TS The maximum design temperature, TS < 50 C.
6)
The maximum design pressure PS is calculated according to EN 13480. See pressure chart below.
Design PS Bends are not calculated.
M ax pressure for piping, P195T R2 and P235T R2. EN 13480-3. Normal wall.
Allowances for corrosion = 0,5mm. Welding factor = 0,85. No allowances for thinning under bending, straving, threading etc is made.
Normal wall thickness Max. Pressure (P195TR2) Normal wall, 50 deg C
Max. Pressure (P235TR2) Normal wall, 50 deg C
16
14
Max presure, PS [Mpa]
Wall thickness [mm]
12
10
8
6
4
2
0
0 100 200 300 400 500 600
Nominal diameter
7)
Figure 1. P195TR2 or P235TR2 yield strength at room temp may be used up to 50 degr. C
Notes:
Application, Commercial quality: Specification :
Welded tubes in commercial quality (code 2130, 2131, 2133) Designation : Identification :
may be used only for secondary purposes without internal pressure. (example)
Bended tubes: Stålrør
Welded tubes in commercial quality (code 2130, 2131, 2133)
Steel tube
have only limited suitability for bending.
Stahlrohr 2130.114,3x3,6
1. For tolerance, see EN 10255, EN 10216-1 or EN 10216-2 or EN 10217-1 or EN 10217-2. Tube en acier
2. Standard: DIN 2448 / 1629 is replaced by EN 10216-1.
Tube de acero
3. Standard: DIN 2458 / 1615 is replaced by EN 10219-1 and EN 10219-2.
“Hollow sections”. Purchase part 2130 is now specified according to 10217-1.
4. Standard: DIN 2458 / 1626 is replaced by EN 10217-1.
5. P195GH - W nr. 1.0348. Steel with specified elevated temperature properties.
6. For tubes exposed to additional load stresses, the maximum pressure has to be reduced accordingly.
For example bending of tubes, threading, support load, branches, corrosion, welding factor different to 1 etc.
7. See EN 13480-3 (4.2.2.1)
Steel Tubes
Electric welded or submerged arc-welded, Hot formed or hot formed + cold finished.
Tube manufacturing process longitudinal or helical seam or continuous
welded.
As welded or full pipe normalized or Normalized or normalizing formed.
Delivery condition
normalized weld zone or normalized rolled.
NDT testing method The full length of the weld seam according to
EN 10246-3, -5, -7, -8 acceptance level 3 sub-
-
category C or EN 10246-9, -10 image quality
class R2.
Each tube in one end. (Du ≤ 51 label on
Each tube in one end. (Du ≤ 51 label on bundle
bundle or box):
or box):
Manufacturer’s mark
Manufacturer’s mark
Type of tube
Marking of tubes with a 3.1.B EN 10216-1 P235TR2
EN 10217-1 P235TR2
certificate. (specific Cast number or code
Category indicator (if applicable)
inspection). Mark of inspection representative
Cast number or code
Identification number which correlates the
Mark of inspection representative
product to the documentation
Identification number which correlates
the product to the documentation
:
Steel Tubes
/4 * DN * 10
2 -6 2
An Nominal inside cross section m
* DN * 10
-3 2
Fn Nominal inside surface m /m
* d1 * 10
-3 2
Fu Outside surface m /m
/4 * d * 10
2 -6 2
Av Exact inside cross section m
/4 * (d1 - d )
2 2 2
Ar Circular cross section mm
/64 * (d1 - d )
4 4 4
Ib Equatorial surface moment of inertia mm
4
Iv Polar surface moment of inertia 2 * lb mm
3
Wb Equatorial section modulus 2 * lb/d1 mm
3
Wv Polar section modulus 2 * Wb mm
I Radius of inertia lb / A r mm
3
V Tube volume Av m /m