Professional Documents
Culture Documents
INTERNSHIPS TITLES
PLC
Parking lot.
Home Automation ( Tank level control ).
Home Automation (Lighting control ).
Sequential on & off of multiple loads.
Counter, comparator & math based application of industry.
Automation of forward reverse motor with interlock.
Exit and parking area automation at the end of the day.
Bottle filling application of conveyer belt.
A single PB (NO ) is used to turn On and OFF the Motor.(Alternate presses and releases
turn On and OFF the motor)
Automation for coordination of multiple conveyers
Multiple conveyers packaging application automation.
SCADA / HMI
Application to turn ON the output (light), when the input push button is pressed. Output
turns OFF when the same input push button is released.
There are 3 switches and 3 lamps
o a)if switch 1 is closed, lamp 1 is ON
o b)if switch 2 is closed, lamp 1 and lamp 2 are ON
o c)if switch 3 is closed, all three lamps should be ON
Application to turn ON the output (light), when the input push button-1 is pressed and
released. Output turns OFF when the input push button-2 is pressed and released.
If any one Smoke sensor gives signal , nothing happens.
o If any two Smoke sensors give signal, warning light turns ON.
o If any 3 Smoke sensors give signal, Alarm starts.
o If all 4 Smoke sensors give signal, Fire extinguisher starts.
# 10-3-282/D/1, Lane beside NEERU’s,
Humayun Nagar, Mehdipatnam, Hyderabad-28
+91-9885359660.Email:ermtinfo@gmail.com
GSTIN:-36ARJPM4584B1ZP
Basic Analog operations to show Rotation, Resizing, Colour blinking, Colour filling,
Visibility on-off, Horizontal movement, Vertical movement, Slanting movement and
Blinking .
Application to show tank level control. The tank is fitted with a low level limit switch and a
high level limit switch.
o a)Pump motor turns ON when water level is at the bottom of tank.
o b) Pump motor turns off when water level is at the top of the tank
If switch 1 closed, lamp A, turns ON. Lamp B turns on after 8 seconds. Both lamps turn
OFF, if switch 1 is opened.
There are 3 motors and 1 input PB . When you press and release the input PB, motor 1
should turn ON, and turn OFF after 5 seconds. Motor 2 should turn ON when motor 1
turns OFF and it should turn OFF after 5 seconds. Motor 3 should turn on after motor 2
has turned OFF and it should turnoff after 5 seconds. Now motor 1 starts again and the
cycle repeats for 5 times after which all motors turn OFF.
Parking area has a capacity of 10 vehicles. When parking area is empty, Entry gate is
open and exit gate is closed. When 1st vehicle enters, exit gate also opens. When 10
vehicles enter the parking area, then entry gate will be closed.
There are two conveyer belts. One conveyer carries items and drops them 1 by 1 in the
basket on the second conveyer belt, which carries the basket for packing.When sensor
senses a basket, the basket conveyer should stop. Then items conveyer starts to fill 10
items in the basket. When 10 items are filled, items conveyer stops and basket conveyer
starts. This cycle repeats until the sensor has not sensed the basket for 20 seconds.
Multifan Application.
Batch Process application
Trends, Alarms, Screen Navigation, Recipe and Security Application.
VFD
Introduction to VFD
Speed control of induction motor using VFD.
Running an induction motor in different directions with different speeds
Motor control with speed locks like LSP , HSP.
# 10-3-282/D/1, Lane beside NEERU’s,
Humayun Nagar, Mehdipatnam, Hyderabad-28
+91-9885359660.Email:ermtinfo@gmail.com
GSTIN:-36ARJPM4584B1ZP
AUTOCAD
Designing of Electrical / Mechanical instruments
Creating the layouts in multiple layers
Electrical layouts power, lightning and ac
HVAC layout designing.
ELECTRICAL DESIGN
Overview of building services
Basics of electrical engineering
Electrical Switchgear, Busbar, Wires and Cables, Conduits, Transformers and
Generators Sizing
Short Circuit Calculations
Total Load calculation and Load Balancing in Buildings
Electrical Designing of a Residential Complex
Electrical Designing of a Commercial Complex
Electrical Designing of Gated Community
Automatic switching of motors with time delay
Automatic turning off of devices
Automatic and manual controlling of motors
Interlocking technique between multiple motors
Automatic direction changing in multiple motors
Automatic star delta starter with over load protection.