Professional Documents
Culture Documents
Page 1 of 6
Cerrar SIS
Pantalla anterior
Producto: EXCAVATOR
Modelo: 385C L EXCAVATOR EDA00555
Configuración: 385C L Excavator EDA00001-UP (MACHINE) POWERED BY C-18 Engine
i02236533
The lines and the pipes in the automatic lubrication system are under
extremely high pressure.
Serious injury can result from high pressure grease spraying out
suddenly.
https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe... 5/21/2011
385C L Excavator EDA00001-UP (MACHINE) POWERED BY C-18 Engine(SEBP4294... Page 2 of 6
Illustration 1 g00587364
1. Inspect the level of the reservoir when a message appears on the display which indicates that
the level of grease in the grease reservoir is low.
NOTICE
Make sure that the grease level does not fall below the "MIN" level in
the reservoir. The operation of the automatic lubrication system with
the grease level below "MIN" will damage the front pins and the swing
bearing because not enough grease will be supplied to these areas.
2. If the grease level is lower than "MIN" (2), grease should be added to the reservoir.
NOTICE
NLGI Grade 0 grease or NLGI Grade 1 grease that has a low viscosity
should be used only in cold weather conditions. The consumption of
grease will increase if used in warmer weather.
https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe... 5/21/2011
385C L Excavator EDA00001-UP (MACHINE) POWERED BY C-18 Engine(SEBP4294... Page 3 of 6
NOTICE
Any foreign materials that enter the grease reservoir could restrict the
lubrication lines or damage the valves. Prior to adding the grease to the
reservoir, be sure to wipe any potential contaminants from the grease
fitting and the grease gun nozzle.
NOTICE
When you add grease to the grease reservoir, never add the grease
beyond the "MAX" level. If you add grease above this level, the cover
of the grease reservoir could come off during operation. The capacity
of the grease reservoir is 8 L (2.1 US gal).
Illustration 2 g00607270
3. Install grease cartridge (4) in grease gun (3). The grease gun is located in the storage box.
https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe... 5/21/2011
385C L Excavator EDA00001-UP (MACHINE) POWERED BY C-18 Engine(SEBP4294... Page 4 of 6
Illustration 3 g00607271
4. Remove cap (5) from the fill port of the electric pump (6) .
https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe... 5/21/2011
385C L Excavator EDA00001-UP (MACHINE) POWERED BY C-18 Engine(SEBP4294... Page 5 of 6
Illustration 4 g00607272
5. Unscrew the cap from the tip of grease gun (3). Attach the end of the grease gun to the threaded
fill port that is on top of electric pump (6) .
6. Tighten the grease gun until the head of the thread is in contact with the fill port.
https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe... 5/21/2011
385C L Excavator EDA00001-UP (MACHINE) POWERED BY C-18 Engine(SEBP4294... Page 6 of 6
Illustration 5 g00607273
(7) Handle
7. Gradually push handle (7) of grease gun (3) until the reservoir is filled to the "MAX" level.
8. After the supply of grease is finished, remove grease gun (3). Clean the fill port and install cap
(5) .
Use a multipurpose type grease that contains three to five percent molybdenum. Use NLGI Grade 2
grease that meets the requirements for cold weather conditions and hot weather conditions.
Copyright 1993 - 2011 Caterpillar Inc. Sat May 21 18:22:33 UTC-0400 2011
Todos los derechos reservados.
Red privada para licenciados del SIS.
https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe... 5/21/2011