Professional Documents
Culture Documents
IMoM 6B PDF
IMoM 6B PDF
IMoM 6B PDF
In many structures the members are required to resist more than one kind of loading
(combined loading). These can often be analyzed by superimposing the stresses and
strains cause by each load acting separately.
Superposition of stresses and strains is permissible only under the following
conditions:
a.The stresses and the strains must be a linear function of the applied loads (Hooke’s
law must be obeyed and the displacements must be small).
b.There must be no interaction between the various loads.
Examples: wide‐flange beam supported by a cable (combined bending and axial
load), cylindrical pressure vessel supported as a beam, and shaft in combined torsion
and bending.
Method of Analysis:
1.Select the point on the structure where the stresses and the strains are to be determined.
2.For each load on the structure, determine the stress resultant at the cross section
containing the selected point..
3.Calculate the normal and shear stresses at the selected point due to each of the stress
resultant.
4.Combine the individual stresses to obtain the resultant stresses at the selected point.
5.Determine the principal stresses and maximum shear stresses at the selected point.
6.Determine the strains at the point with the aid of Hooke’s law for plane stress.
7.Select additional points and repeat the process.
P Τρ My
σ= τ= σ =−
A Ιρ I
VQ pr
τ= σ=
Ib t
Illustration of the Method:
The bar shown is subjected to two types of loads: a
torque T and a vertical load P.
Let us select arbitrarily two points. Point A (top of
the bar) and point B (side of the bar ‐ in the same
cross section).
The resulting stresses acting across the section are
the following:
‐ A twisting moment equal to the torque T.
‐ A bending moment M equal to the load P times
the distance b.
‐ A shear force V equals to the load P.
The twisting moment Τ produces a torsional shear stresses
Tr 2T
τ torsion = = 3
I Polar πr
The stress τ1 acts horizontally to the left at point A and
vertically downwards at point B.
The bending moment M produces a tensile stress at point A
Mr 4 M
σ bending = = 3
I πr
However, the bending moment produces no stress at point B, because B is
located on the neutral axis.
The shear force V produces no shear stress at the top of the
bar (point A), but at point B the shear stress is as follows:
VQ 4V
τ shear = =
Ib 3 A
σA and τ1 are acting in point A, while the τ1 and τ2 are acting
in point B.
Note that the element is in plane stress with
σx = σA, σy = 0 , and τxy = - τ1.
A stress element in point B is also in plane stress and the
only stresses acting on this element are the shear
stresses τ1 and τ2. Therefore
σx = σy = 0 and τxy = - (τ1 + τ2).
For instance, the normal stresses due to bending
are largest at the cross section of maximum
bending moment, which is at the support.
Therefore, points C and D at the top and bottom
of the beam at the fixed ends are critical points
where the stresses should be calculated.
Selection of Critical Areas and Points
If the objective of the analysis is to determine the largest stresses anywhere in the
structure, then the critical points should be selected at cross sections where the
stress resultants have their largest values.
Furthermore, within those cross sections, the points should be selected where
either the normal stresses or the shear stresses have their largest values.
Stress at which point?
The rotor shaft of an helicopter drives the rotor blades that provide the lifting
force to support the helicopter in the air. As a consequence, the shaft is
subjected to a combination of torsion and axial loading.
For a 50mm diameter shaft transmitting a torque Τ = 2.4kN.m and
a tensile force P = 125kN, determine the maximum tensile stress,
maximum compressive stress, and maximum shear stress in the
shaft.
Solution
σ 1, 2 = ⎜ ± ⎟ + (− 97.78)
2
⎟ ⎜
The maximum in-plane shear ⎝ 2 ⎠ ⎝ 2 ⎠
σ − σ
2
⎛ ⎞
⎟⎟ + (τ ) = 103MPa
σ 1 = 135MPa τ = ⎜⎜
x y 2
stresses are obtained using the MAX
⎝ 2 ⎠
xy
formula
σ 2 = −71MPa
Because the principal stresses σ1 and σ2 have opposite signs, the maximum in-plane
shear stresses are larger than the maximum out-of-plane shear stresses. Therefore,
the maximum shear stress in the shaft is 103MPa.
480 MPa
2 = 2.33 σ VM = (135)2 − (135)(− 71) + (− 71)2 = 181.2 MPa
MSST ⇒ SF =
103MPa 480 MPa
DET ⇒ SF = = 2.65
181.2 MPa
A thin wall cylindrical pressure vessel with a circular cross section is
subjected to internal gas pressure p and simultaneously compressed by an
axial load P = 12k. The cylinder has inner radius r = 2.1in. And wall thickness t
= 0.15in. Determine the maximum allowable internal pressure pallow based
upon an allowable shear stress of 6500psi in the wall of the vessel.
Solution
The stresses on the wall of the pressure vessel are caused by a combined action of
the internal pressure and the axial force. We can isolate a stress element in point A.
The x-axis is parallel to the longitudinal axis of the pressure vessel and the y-axis is
circumferential. Note that there are no shear stresses acting on the element.
The longitudinal stress σx is equal to the tensile stress
produced by the internal pressure minus the
compressive stress produced by the axial force.
pr P pr P
σx = − = −
2t A 2t 2πrt
The circumferential stress σy is equal to the tensile pr
σy =
stress produced by the internal pressure. t
Note that σy > σx .
pr
Since no shear stresses act on the element the σ1 = σ y =
t
above stresses are also the principal stresses
pr P
σ2 = σx = −
substituting numerical values 2t 2πrt
pr p (2.1in )
σ1 = = = 14 .0 p
t 0.15in
pr P p (2.1in ) 12 k
σ2 = − = − = 7.0 p − 6063 psi
2t 2πrt 2(0.15in ) [2π (2.1in )(0.15in )]
τ Max =
(σ 1 − σ 2 ) = ((14.0 p ) − (7.0 p − 6063 psi )) = 3.5 p + 3032 psi
2 2
Since τmax is limited to 6500psi then
65000 psi = 3.4 p + 3032 psi ⇒ pallowed = 990 psi
Out-of-Plane Shear Stresses σ1
The maximum out-of-plane shear stress is either
τ Max =
2
From the first equation we get σ2
τ Max =
65000 psi = 3.5 p − 3032 psi 2
pallowed = 2720 psi
From the second equation we 65000 psi = 7.0 p ⇒ pallowed = 928 psi
get:
Solution
Stress Resultant: The wind pressure against the sign
produces a resultant force W that acts at the midpoint
of the sign and it is equal to the pressure p times the
area A over which it acts:
W = pA = (2.0kPa )(2.0m × 1.2m ) = 4.8kN
The line of action of this force is at height h = 6.6m above the ground and at
distance b = 1.5m from the centerline of the pole.
The wind force acting on the sign is statically equivalent to a lateral force W
and a torque Τ acting on the pole.
The torque is equal to the force W
times the distance b:
T = Wb = (4.8kN )(1.5m )
T = 7.2kN − m
The stress resultant at the base of the pole consists of a bending moment M, a
torque Τ and a shear force V. Their magnitudes are:
M = Wh = (4.8kN)(6.6m) = 31.68kN.m
Τ = 7.2kN.m
V = W = 4.8kN
Examination of these stress resultants shows that maximum bending stresses
occur at point A and maximum shear stresses at point B.
Therefore, A and B are critical points where the stresses should be determined.
Stresses at points A and B
The bending moment M produces a tensile stress σa at point A, but no stress at
point B (which is located on the neutral axis)
⎛ d2 ⎞
M⎜ ⎟
σa = ⎝ 2 ⎠ = (31.68kN )(0.11m ) = 54.91MPa
( ) (
⎡ π d 24 − d14 ⎤ ⎡ π 0.224 − 0.184 ⎤ )
⎢ ⎥ ⎢ ⎥
⎣ 64 ⎦ ⎣ 64 ⎦
The torque Τ produces shear stresses τ1 at points A and B.
⎛d ⎞
T⎜ 2 ⎟
τ Torsion = ⎝ 2⎠
=
(7.2kN .m )(0.11m )
= 6.24 MPa
( ) (
⎡ π d 2 − d1 ⎤ ⎡ π 0.22 − 0.18 ⎤
4 4 4 4
)
⎢ ⎥ ⎢ ⎥
⎣ 32 ⎦ ⎣ 32 ⎦
Finally, we need to calculate the direct shear stresses at points A and B
due to the shear force V.
VQ
The shear stress at point A is zero, and the shear stress at τ2 =
Ib
point B (τ2) is obtained from the shear formula for a circular
tube
2(4800 ) I =⎢
(
⎡ π d 24 − d14 ⎤)
2V ⎥
τ 2, Max = = 2
= 0.7637 MPa ⎣ 64 ⎦
A 0.01257 m
(
2 3 3
Q = r2 − r1
3
)
The stresses acting on the cross section at points A and B
have now been calculated. b = 2(r2 − r1 )
Stress Elements
For both elements the y-axis is parallel to the longitudinal
axis of the pole and the x-axis is horizontal.
Point A :
σx = 0
σy = σa = 54.91MPa
τxy = τ1 = 6.24MPa
⎛σ x +σ y ⎞ ⎛σ x −σ y ⎞
2
Principal stresses at Point A σ 1, 2 = ⎜⎜ ⎟⎟ ± ⎜⎜ ⎟⎟ + (τ xy )2
⎝ 2 ⎠ ⎝ 2 ⎠
Substituting σ1,2 = 27.5MPa +/- 28.2MPa
σ1 = 55.7MPa and σ2 = - 0.7MPa
The maximum in-plane shear ⎛σ −σ
2
⎞
stresses can be obtained from τ MAX = ⎜⎜ x y
⎟⎟ + (τ xy )2
= 28 . 2 MPa
the equation ⎝ 2 ⎠
Because the principal stresses have opposite signs, the maximum in-plane
shear stresses are larger than the maximum out-of-plane shear stresses.
Then, τmax = 28.2MPa.
Point B :
σx = σy = 0
τxy = τ1 + τ2
τxy = 6.24MPa + 0.76MPa = 7.0MPa
Principal stresses at point B are
σ1 = 7.0MPa σ2 = - 7.0 MPa
And the maximum in-plane shear stress is
τmax = 7.0MPa
The maximum out-of-plane shear stresses are half of
this value.
Note
If the largest stresses anywhere in the pole are needed, then we must also
determine the stresses at the critical point diametrically opposite point A,
because at that point the compressive stress due to bending has its largest
value.
The principal stresses at that point are
σ1 = 0.7MPa and σ2 = - 55.7MPa
The maximum shear stress is 28.2MPa.
(In this analysis only the effects of wind pressure are considered. Other loads, such as
weight of the structure, also produce stresses at the base of the pole).
A tubular post of square cross section supports a
horizontal platform (see figure).
The tube has outer dimension b = 6in.
And wall thickness t = 0.5in.
The platform has dimensions 6.75in x 24.0in and
supports an uniformly distributed load of 20psi acting
over its upper surface.
The resultant of this distributed load is a vertical
force
P1 = (20psi)(6.75in x 24.0in) = 3240lb
This force acts at the midpoint of the platform, which
is at distance
d = 9in. from the longitudinal axis of the post.
A second load P2 = 800lb acts horizontally on the
post at height h = 52in above the base.
Determine the principal stresses and maximum
shear stresses at points A and B at the base of the
post due to the loads P1 and P2.
Solution
Stress Resultants
The force P1 acting on the platform is statically
equivalent to a force P1 and a moment
M1 = P1d acting on the centroid of the cross section
of the post.
The load P2 is also shown.
The stress resultant at the base of the post due to the
loads P1 and P2 and the moment M1 are as follows:
(A) An axial compressive force P1 = 3240lb
(B) A bending moment M1 produced by the force P1:
M1 = P1d = (3240lb)(9in) = 29160lb-in
(C) A shear force P2 = 800lb
(D) A bending moment M2 produced by the force P2:
M2 = P2h = (800lb)(52in) = 41600lb.in
σy = - σB = - 1860psi σ 1, 2 = ⎜⎜ ⎟⎟ ± ⎜⎜ ⎟⎟ + (τ xy )2
τxy = - τP2 = - 160psi ⎝ 2 ⎠ ⎝ 2 ⎠
The maximum in-plane shear stresses can be obtained from the equation
Because the principal stresses have opposite signs, the maximum in-plane
shear stresses are larger than the maximum out-of-plane shear stresses.
Then, τmax = 944psi. ⎛σ x ⎞
2
⎝ 2 ⎠
Three forces are applied to a short steel post as
shown. Determine the principle stresses,
principal planes and maximum shearing stress
at point H.
Solution
Determine internal forces in Section EFG.
Vx = −30 kN P = 50 kN Vz = −75 kN
M x = (50 kN )(0.130 m ) − (75 kN )(0.200 m )
M x = −8.5 kN ⋅ m
My = 0 M z = (30 kN )(0.100 m ) = 3 kN ⋅ m
A = (0.040 m )(0.140 m ) = 5.6 × 10−3 m 2
Note: Section properties,
1 (0.040 m )(0.140 m )3 = 9.15 × 10− 6 m 4
I x = 12
Evaluate the stresses at H. 1 (0.140 m )(0.040 m )3 = 0.747 × 10 − 6 m 4
I z = 12
Normal stress at H.
P Mz a Mx b
σy =+ + −
A Iz Ix
=
50 kN
+
(3 kN ⋅ m )(0.020 m )
5.6 × 10-3 m 2 0.747 × 10−6 m 4
−
(8.5 kN ⋅ m )(0.025 m )
9.15 × 10−6 m 4
Shear stress at H.
Q = A1 y1 = [(0.040 m )(0.045 m )](0.0475 m ) = (8.93 + 80.3 − 23.2 ) MPa = 66.0 MPa
= 85.5 × 10−6 m3
τ yz =
Vz Q ( (
75 kN ) 85.5 × 10− 6 m3)
I xt
=
( )
9.15 × 10−6 m 4 (0.040 m )
= 17.52 MPa
Calculate principal stresses and maximum shearing stress.
σ VM = (σ + 3τ )
1
2 2 2
x zx
64
3) Chose the failure
⎛d ⎞
criteria. T⎜ ⎟
Tr ⎝ 2 ⎠ 16 × F × 15in
τ zx = = = = 76.4 F
The AISI 1035 is a J πd 4
π (1in) 3
ductile material. Hence,
we need to employ the 32
distortion-energy
theory.
σ VM = σ x 2 + σ y 2 − σ xσ y + 3τ xy2 = σ x 2 + 3τ zx2 = 194.5F
Sy 81000
F= = = 416lbf
σ VM 194.5
Apply the MSS theory. For a point undergoing plane stress with
only one non-zero normal stress and one shear stress, the two non-
zero principal stresses (σA and σB) will have opposite signs (Case 2).
σ A −σ B ⎛σx ⎞
2
Sy
τ max = = = ± ⎜ ⎟ + τ zx2
2 2 ⎝ 2 ⎠
⎛σx ⎞
2
σ A − σ B ≥ S y = 2 ⎜ ⎟ + τ zx2 = σ x 2 + 4τ zx2
⎝ 2 ⎠
(
81000 = (142.6 F ) + 4 × (76.4 F )
2 2
)
1
2
F = 388lbf
A round cantilever bar is subjected to torsion plus a transverse load at
the free end. The bar is made of a ductile material having a yield
strength of 50000psi. The transverse force (P) is 500lb and the torque
is 1000lb-in applied to the free end. The bar is 5in long (L) and a
safety factor of 2 is assumed. Transverse shear can be neglected.
Determine the minimum diameter to avoid yielding using both MSS
and DET criteria.
Solution
⎛σ x +σ y ⎞ ⎛σ x −σ y ⎞
2
⎛σ ⎞ ⎛σ ⎞
2
σ 1, 2 = ⎜⎜ ⎟⎟ ± ⎜⎜ ⎟⎟ + (τ xy )2 = ⎜ x ⎟ ± ⎜ x ⎟ + (τ xy )2
⎝ 2 ⎠ ⎝ 2 ⎠ ⎝ 2 ⎠ ⎝ 2 ⎠
2 2
⎛ 16 PL ⎞ ⎛ 16T ⎞ 16 ⎡
σ 1, 2 =
16 PL
± ⎜ ⎟ + ⎜ ⎟ = 3 ⎢
PL ± (PL )2 + T 2 ⎤⎥
πd 3
⎝ πd ⎠ ⎝ πd ⎠
3 3
πd ⎣ ⎦
πd ⎢⎣ ⎥⎦
26450 980.8 The stresses are in the wrong
σ1 = σ2 = − 3 order.. Rearranged to
d3 d
26450 980.8
σ1 = σ3 = − 3
d3 d
σ1 −σ 3 26450 − ( − 980 . 8 ) 13715 . 4
τ MAX = = 3
=
MSS 2 2d d3
Sy 50000
σ 1 − σ 3 = 2τ MAX ≤ = = 25 , 000
n 2
d ≥ 1 . 031 in
2 2
⎛ 26450 ⎞ ⎛ 980.8 ⎞ ⎛ 26450 ⎞⎛ 980.8 ⎞
σ VM = σ 1 + σ 3 − σ 1σ 3 = ⎜ 3 ⎟ + ⎜ − 3 ⎟ − ⎜ 3 ⎟⎜ − 3 ⎟
2 2
⎝ d ⎠ ⎝ d ⎠ ⎝ d ⎠⎝ d ⎠
DET
26950 S y 50000
σ VM = 3
≤ =
d n 2
d ≥ 1.025in
The factor of safety for a machine
element depends on the particular
point selected for the analysis. Based
upon the DET theory, determine the
safety factor for points A and B.
Solution: ⎛d ⎞
Fl ⎜ ⎟
Point A σ x =
Mc
+
P
= ⎝ 2⎠ P
+ 2 =
32 Fl 4 P
+ 2
I Area πd 4
πd πd 3
πd
64 4
σx =
( ) +
( )
32(0.55) 103 (0.1) 4(8) 103
= 95.49 MPa
π (0.02)3
π (0.02)2
Tr 16T 16(30)
τ xy = = 3 = = 19.10 MPa
J πd π (0.020 )3
(σ ) = [95.49 + 3(19.1) ]
1
σ VM = 2
x + 3τ 2
xy
2 2 2
= 101.1MPa
Sy 280
n= = = 2.77
σ VM 101.1
Point B 4 P 4(8) 103
σx = 2 = = 25.47 MPa
( )
πd π (0.02)2
τ xy
16T 4V
= 3+ =
16(30)
+
4(0.55) 103
= 21.43MPa
( )
πd 3 A π (0.02 )3
⎛π ⎞
3⎜ ⎟(0.02)
2
⎝4⎠
[
σ VM = 25.47 + 3(21.43) 2 2
] 1
2
= 45.02 MPa
280
n= = 6.22
45.02
The shaft shown in the figure below is supported by two bearings and carries two V-
belt sheaves. The tensions in the belts exert horizontal forces on the shaft, tending to
bend it in the x-z plane. Sheaves B exerts a clockwise torque on the shaft when
viewed towards the origin of the coordinate system along the x-axis. Sheaves C
exerts an equal but opposite torque on the shaft. For the loading conditions shown,
determine the principal stresses and the safety factor on the element K, located on the
surface of the shaft (on the positive z-side), just to the right of sheave B. Consider
that the shaft is made of a steel of a yield strength of 81ksi
Shearing force = 165lb
Bending Moment = -1540lb-in
Mc M (r ) − 1540
σx = − =− = −4 = 8.031ksi
I πr 4 π (0.625)3
4
Tr 2T 2(1100 )
τ xz = = 3= = 2.868ksi
J πr π (0.625)3
⎛σ +σ y ⎞ ⎛σx −σ y ⎞
2
⎛σx ⎞ ⎛σx ⎞
2
σ 1, 2 = ⎜⎜ x ⎟⎟ ± ⎜⎜ ⎟⎟ + (τ xy ) = ⎜ ⎟ ± ⎜ ⎟ + (τ xy )2
2
⎝ 2 ⎠ ⎝ 2 ⎠ ⎝ 2 ⎠ ⎝ 2 ⎠
2
⎛ 8.03 ⎞
⎟ + (2.868)
8.03
σ 1, 2 = ± ⎜
2
2 ⎝ 2 ⎠
σ 1 = 8.95ksi σ 2 = −0.92ksi
σ1 − σ 3 8.95 − (− 0.92 )
MSS .....τ Max = = = 4.935ksi
2 2
SY 81
Safety..Factor = n = 2 = 2 = 8.2
τ Max 4.935
DET ......σ VM = σ 1 + σ 3 − σ 1σ 3 =
2 2
(8.95)2 + (− 0.92)2 − (8.95)(− 0.92) = 9.44ksi
Sy 81
Safety..Factor = n = = = 8.58
σ VM 9.44
A horizontal bracket ABC consists of two perpendicular arms AB and BC, of
1.2m and 0.4m in length respectively. The Arm AB has a solid circular cross
section with diameter equal to 60mm. At point C a load P1=2.02kN acts
vertically and a load P2=3.07kN acts horizontally and parallel to arm AB.
For the points p and q, located at support A, calculate:
(1)The principal stresses.
(2) the maximum in-plane shear stress.
1.2m