Professional Documents
Culture Documents
Untrained Personnel. P= 3XB (M) Use certified scaffolders. P= 1XB (L) PTW Supervisor
A= 3XB (M) Adequate Supervision A= 1XB (L) & Safety Officer
E= 0XA (NA) E= 0XA (NA)
R= 3XB (M) R= 1XB(L)
falls from height, P= 3XB (M) Use fall protection equipment. P= 1XB (L) PTW Supervisor
A= 0XA (NA) All safety equipment must be inspected. A= 0XA (NA) & Safety
E= 0XA (NA) Only certified Scaffolder will be allowed to work. E= 0XA (NA) Officer/scaffolders
R= 3XB (M) Use safety harness with double lanyard when working at R=1XB(L)
height.
Ensure safety harness to have 3rd party certificates with
BCP stamp.
Other parties working in the area will be notified and
advised to leave the area.
Adequate barricading with appropriate safety signage will
be installed.
Maintain 3point contact of all time while ascending and
descending ladder.
Be aware of slippery surfaces. .
Ensure use of safety harness with 100% tie off.
Use third party certified and BCP approved Safety
Harness
Falling object P= 3XB (M) Work area must be properly barricaded and restricted. P= 1XB (L) PTW Supervisor
A= 0XA (NA) Adequate Supervision A= 0XA (NA) & Safety
E= 0XA (NA) Ensure proper lowering of components using approved E= 0XA (NA) Officer/scaffolders
R= 3XB (M) method, approved scaffolding lifting bag• R= 1XB(L)
Cordon off area • Store loose materials (ties, clamps and
etc.) in sacks or bag.
All openings in the platform to be adequately covered.
Barricade the area and provide safety signage.
Limited access to be done
Don’t drop the materials use Approved Scaffolding
material’s bag
Secure all tools and materials at all times
Do not throw the ,secure all the hand tools using lanyard,
barricades the area with display of sign boards
5 Manual loading and Improper handling of P= 3XB (M) Appropriate Supervision. P= 1XB (L) PTW Supervisor
unloading works material. A= 0XA (NA) Access from the storage to the Loading/offloading site A= 0XA (NA) & Safety
E= 0XA (NA) must be clear. E= 0XA (NA)
R= 3XB (M) R= 1XB (L)
Procedure Ref : IP-OPS-066
JHA No.: Mech-05-20 Revision No:0 Area: xxxxxxxxxx Job Locations:
Rev.: A1 Date:24/09/2020
JOB HAZARD ANALYSIS Date: Dec. - 2014
Job Ref (Contract No.: xxxxxxxxxxxxxxxxxx Hazardous Area Classification: Zone 0☐, Zone 1☐,
PageZone 2󠇯☑󠇯, Non Hazardous☐
5 of 12
Job Description: Erection of scaffolding. Permit Type & No. :
E= 0XA (NA) Never use a damaged or defective hand or power tool. E= 0XA (NA)
R= 3XB (M) Tools are not toys. Never throw or toss a tool in the R= 1XB (L)
direction of or directly to a coworker.
All operatives shall be trained for proper handling of tools
Appropriate tools only have to be used and its
requirements.
Inspect the tools .Don’t use defective tools .Defective
tools must be remove from the site to avoid the usage of
defective tools which may cause of incident.
All operatives shall wear their PPEs without fail.
Poor ergonomics P= 3XB (M) Good posture is about more than finding a comfortable P= 1XB (L) PTW Supervisor
A= 0XA (NA) position to work in, or what “feels right.” Especially when A= 0XA (NA) & Safety
E= 0XA (NA) you consider that some positions, while comfortable for E= 0XA (NA) Officer/All
R= 3XB (M) the worker, may not be ergonomically correct. R= 1XB (L)
Change it Up
Repeating the same movement continuously through the
day can cause strains. If it is possible to alternate tasks, it
is advisable to do so. If job rotation or alternating tasks
throughout the shift is unrealistic.
Be sure to incorporate several rest breaks. Stretch during
breaks, or do simple exercises to keep your muscles and
tendons from becoming tense or strained.
Be sure that if your job involves manual lifting, that you
are trained in manual material handling, and that you
practice proper lifting techniques. Never lift with the
muscles in your back. Lift with your knees.
Risk of striking hand P= 3XB (M) Ensure other personnel are well clear. P= 1XB (L) PTW Supervisor
A= 0XA (NA) Make sure you are using the correct tool for the task at A= 0XA (NA) & Safety
E= 0XA (NA) hand E= 0XA (NA) Officer/scaffolders
R= 3XB (M) Beware of sharp edges on tools R= 1XB (L)
The right tool for the job should always be used to
decrease the chances of injury, incidents, or damage to a
tool through improper use
Risk of striking others P= 3XB (M) Never use a damaged or defective hand or power tool P= 1XB (L) PTW /Supervisor
A= 0XA (NA) Keep only required persons at site. A= 0XA (NA) & /scaffolders
E= 0XA (NA) All tools shall be kept clean for easy use. E= 0XA (NA)
R= 3XB (M) Ensure other personnel are well clear. R= 1XB (L)
Proper communication each other.
Procedure Ref : IP-OPS-066
JHA No.: Mech-05-20 Revision No:0 Area: xxxxxxxxxx Job Locations:
Rev.: A1 Date:24/09/2020
JOB HAZARD ANALYSIS Date: Dec. - 2014
Job Ref (Contract No.: xxxxxxxxxxxxxxxxxx Hazardous Area Classification: Zone 0☐, Zone 1☐,
PageZone 2󠇯☑󠇯, Non Hazardous☐
7 of 12
Job Description: Erection of scaffolding. Permit Type & No. :
Make sure you are using the correct tool for the task at
hand.
Tools are not toys. Never throw or toss a tool in the
direction of or directly to a coworker.
Sharp Objects P= 3XB (M) Wear hand protection P= 1XB (L) PTW Supervisor
A= 0XA (NA) Remove sharp edges. A= 0XA (NA) & Safety Officer
E= 0XA (NA) Safety signage describing the hazards should be present. E= 0XA (NA)
R= 3XB (M) R= 1XB (L)
slip, trip and falls P= 3XB (M) Suitable means of access. P= 1XB (L) PTW Supervisor
A= 0XA (NA) Good housekeeping and PPE’s must be worn (hand A= 0XA (NA) & Safety Officer
E= 0XA (NA) gloves). E= 0XA (NA)
R= 3XB (M) Provide sufficient access and working platform R= 1XB (L)
Platform shall be inspected and green tagged, same
applies for access ladders.
Watch & be cautious for slippery wet surfaces
Area must be barricaded and signs must be posted.
Pinch point P=3xB (M) TBT to be conducted and close supervision to by carried P= 1XB (L) PTW Supervisor
A=0xA (NA) out. A= 0XA (NA) & Safety Officer
E=0xA (NA) Hand gloves to be used. E= 0XA (NA)
R=3xB (L) Safety signage describing the hazards should be present. R= 1XB (L)
Damaged hand tools P=3xB (M) Ensure that equipment and accessories are of P=1xB (L) PTW Supervisor
A=2xA (NA) appropriate standard & correct specifications A=1xA (L) & Safety Officer
E=0xB (NA) Never use a damaged or defective hand tool E=0xB (NA)
R=3xB (L The damaged Hand tools must be reported and R=1xB (L
immediately return to store.
7 Damage scaffolding P= 3XB (M) Take extreme care during erection of scaffolding for P= 1XB (L) PTW Supervisor
materials A= 0XA (NA) damaged /defective scaffolding materials. A= 0XA (NA) & Safety Officer
E= 0XA (NA) Regularly checking of scaffolding materials for any E= 0XA (NA)
Fall of personnel R= 3XB (M) R= 1XB (L)
damage
Provide guardrail & toe board to prevent falling of tools
/objects/personnel
The damaged scaffolding materials must be reported and
immediately replace with good materials by the certified
scaffolding crew with PTW.
Risk of collapse of P= 3XB (M) P= 1XB (L) PTW Supervisor
scaffolding/working A= 0XA (NA) Area check for scaffolding .Excavation shall not allowed A= 0XA (NA) & Safety Officer
platform E= 0XA (NA) near scaffolding Area E= 0XA (NA)
Procedure Ref : IP-OPS-066
JHA No.: Mech-05-20 Revision No:0 Area: xxxxxxxxxx Job Locations:
Rev.: A1 Date:24/09/2020
JOB HAZARD ANALYSIS Date: Dec. - 2014
Job Ref (Contract No.: xxxxxxxxxxxxxxxxxx Hazardous Area Classification: Zone 0☐, Zone 1☐,
PageZone 2󠇯☑󠇯, Non Hazardous☐
8 of 12
Job Description: Erection of scaffolding. Permit Type & No. :
P= 3XB (M) All waste to be disposed-off as per CLIENT waste P= 2XB (L)
Waste Material A= 0XA (NA) management procedure. A= 0XA (NA) Supervisor, PTW
Generation E= 3XB (M) E= 2XB (L) Holder.
R= 3XB (M) R= 1XB(L)
P= 3XB (M) Wear heavy duty gloves for the task. P= 1XB (L)
A= 0XA (NA) Keep the body parts away from sharp edges. A= 0XA (NA) Supervisor, PTW
Sharp Object
E= 0XA (NA) Protect the sharp edges with some sort of means if E= 0XA (NA) Holder.
R= 3XB (M) possible. R= 1XB(L)
Ensure all equipment / materials removed from area.
Clear the area of any slip, trip or fall hazards.
P= 3XB (M) P= 1XB (L)
All equipment’s and tools removed on completion of job.
Slip, trip and falls A= 0XA (NA) A= 0XA (NA) Supervisor, PTW
Be cautious for the wet slippery surface.
E= 0XA (NA) E= 0XA (NA) Holder.
R= 3XB (M) Regular housekeeping at site shall be performed. R= 1XB(L)
Keep walk ways always clear of obstruction
11 Emergency Lack of awareness P=3xB (M) Conduct TBT prior start the job. P=1xB (L) PTW Supervisor
Preparedness during emergency E=0xA (NA) Ensure supervisor will communicate to all workers how to E=0xA NA) & Safety Officer
situation A=0xB (L) response during emergency and it should understand by A=0xB (L) and all
R=2xB (L R=1xB (L)
Procedure Ref : IP-OPS-066
JHA No.: Mech-05-20 Revision No:0 Area: xxxxxxxxxx Job Locations:
Rev.: A1 Date:24/09/2020
JOB HAZARD ANALYSIS Date: Dec. - 2014
Job Ref (Contract No.: xxxxxxxxxxxxxxxxxx Hazardous Area Classification: Zone 0☐, Zone 1☐,
PageZone
10 of 2󠇯☑󠇯, Non Hazardous☐
12
Job Description: Erection of scaffolding. Permit Type & No. :