Professional Documents
Culture Documents
are_____.
Select one:
a. its ability to withstand impact
b. It should not break into fragment
c. both
Feedback
Question 2
Incorrect
Mark 0.00 out of 1.00
Flag question
Question text
c. Cabin window
Feedback
Question 3
Correct
Mark 1.00 out of 1.00
Flag question
Question text
The heating element that is produced by spaying with a flame gun at 1000c on the inner surface of
the outer glass layer, which is then bonded to the vinyl interlayer is called
Select one:
a. Gold film panel
b. None of them
Question 4
Correct
Mark 1.00 out of 1.00
Flag question
Question text
c. three
Feedback
Question 5
Correct
Mark 1.00 out of 1.00
Flag question
Question text
c. both
Feedback
Question 6
Correct
Mark 1.00 out of 1.00
Flag question
Question text
The ___________ over which two wing skin panels are mated have a T-J cross section.
Select one:
a. Vent stringers
b. Vent splice stringers
c. Splice stringer
Feedback
Question 7
Incorrect
Mark 0.00 out of 1.00
Flag question
Question text
Question 8
Correct
Mark 1.00 out of 1.00
Flag question
Question text
A panel is usually made up of two preformed and pre-tempered glass layers or plies each of which
are bonded to a sandwiched sheet or ply of reinforcing material termed the______.
Select one:
a. Inner layer
b. Center layer
c. interlayer
Feedback
Question 9
Correct
Mark 1.00 out of 1.00
Flag question
Question text
Question 10
Correct
Mark 1.00 out of 1.00
Flag question
Question text
The upper skin panel and the lower skin panel is made of__________.
Select one:
a. 2024 Al alloy
b. 7010 Al
c. damage tolerant
Feedback
Question 2
Correct
Mark 1.00 out of 1.00
Flag question
Question text
Question 3
Correct
Mark 1.00 out of 1.00
Flag question
Question text
What are the design parameters that upper and lower skin panels of the vertical stabilizer need to
follow to meet the structural design requirements?
Select one:
a. it should be countered and twisted
b. it should be tapered and countered
Question 4
Correct
Mark 1.00 out of 1.00
Flag question
Question text
c. Two
Feedback
Question 5
Incorrect
Mark 0.00 out of 1.00
Flag question
Question text
What we use to provide electrical continuity between the tip and the box structure?
Select one:
a. both
b. bonding braide
c. bonding jumpers
Feedback
Question 6
Correct
Mark 1.00 out of 1.00
Flag question
Question text
In composite construction of horizontal stabilizer, why tip of the stabilizer is made up of aluminum
alloy
Select one:
a. To give extra strength
b. To give it thermal resistant for any icing
c. To give it lightning strike protection
Feedback
Question 7
Correct
Mark 1.00 out of 1.00
Flag question
Question text
Question 8
Correct
Mark 1.00 out of 1.00
Flag question
Question text
Question 9
Incorrect
Mark 0.00 out of 1.00
Flag question
Question text
c. Four
Feedback
Question 10
Correct
Mark 1.00 out of 1.00
Flag question
Question text
The torque box is attached to the rear spar by which type of bolts.
Select one:
a. Tension bolts
b. Tears bolts
c. Compression bolts
Feedback
c. Cathodic protection
Feedback
Question 2
Correct
Mark 1 out of 1
Flag question
Question text
Question 3
Correct
Mark 1 out of 1
Flag question
Question text
When we are dealing with zoning for surface protection zone B is allocated to
Select one:
a. fuel tank
b. Area contact with air and water
Question 4
Incorrect
Mark 0 out of 1
Flag question
Question text
c. Both
Feedback
Question 5
Correct
Mark 1 out of 1
Flag question
Question text
Better adhesion is obtained using liquid adhesives and this is usually solidified. This type of adhesion
is called
Select one:
a. Specific adhesion
b. self-locking
c. Mechanical interlocking
Feedback
Question 6
Correct
Mark 1 out of 1
Flag question
Question text
c. Wing tips
Feedback
Question 7
Correct
Mark 1 out of 1
Flag question
Question text
The correct answer is: assembly on racks, surface preparation, anodizing, sealing
Question 8
Correct
Mark 1 out of 1
Flag question
Question text
c. Chemical conversion
Feedback
Question 9
Correct
Mark 1 out of 1
Flag question
Question text
The correct answer is: Non- countersunk rivets are to be preferred to countersunk rivets
Question 10
Incorrect
Mark 0 out of 1
Flag question
Question text
Which statement is not correct when we discuss the advantage of metal bonding
Select one:
a. leak proof joints
b. Low strength to weight ratio
Lecture 2