Professional Documents
Culture Documents
Technical Description
Appendix A – Technical Data
Issue 2.1
Groove G30 FP 2.1
Technical Description Groove G30 confidential
2/22 Appendix A FP 2.1 – Technical Data
December 2017 / Issue 2_1 h r
The information contained in this document is confidential and the property of Coriant GmbH and is supplied without liability
for errors or omissions. It is subject to change without notice and describes only the product defined in the introduction of this
documentation. This documentation is intended for the use of Coriant GmbH customers only for the purposes of the agreement
under which the document is submitted, and no part of it may be used, reproduced, modified or transmitted in any form or
means without the prior written permission of Coriant GmbH. Coriant GmbH welcomes customer comments as part of the
process of continuous development and improvement of the documentation.
This Technical Description is provided as a generic descriptive document only. It does not include any legally
binding statement. The product features, and details thereof, discussed in this Technical Description may include those that
prove to be temporarily or permanently unavailable. Coriant GmbH reserves the right to alter without notice the specification,
design, price or conditions of supply of any product or service.
Coriant GmbH will correct errors in this documentation as soon as possible. IN NO EVENT WILL Coriant GmbH BE LIABLE
FOR ERRORS IN THIS DOCUMENTATION OR FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO SPECIAL,
DIRECT, INDIRECT, INCIDENTAL OR CONSEQUENTIAL OR ANY LOSSES, SUCH AS BUT NOT LIMITED TO LOSS OF
PROFIT, REVENUE, BUSINESS INTERRUPTION, BUSINESS OPPORTUNITY OR DATA,THAT MAY ARISE FROM THE
USE OF THIS DOCUMENT OR THE INFORMATION IN IT.
This documentation and the product it describes are considered protected by copyrights and other intellectual property rights
according to the applicable laws.
Other product names mentioned in this document may be trademarks of their respective owners, and they are mentioned for
identification purposes only.
Copyright © Coriant GmbH 2016. All rights reserved. The copyright and the foregoing restrictions on reproduction and use
extend to all media in which the information may be embodied.
Contents
1. Traffic Interfaces ................................................................... 5
1.1 Transponder Client Interfaces ......................................................................... 5
1.1.1 QSFP+ Client Interfaces .................................................................................. 6
1.1.2 100G QSFP28 Client Interfaces ...................................................................... 7
1.2 Transponder Line Interfaces .......................................................................... 10
1.2.1 CHM-1 and CHM-2 with 200G CFP2 ACO .................................................... 10
1.3 Pluggables: QSFP28/+ .................................................................................. 14
1.4 Transponder Latency Time ............................................................................ 15
Tables
Table 1: Overview of available client interfaces (note software release support must be
checked from Roadmaps) ........................................................................................... 5
Table 2: 40G QSFP+ Parameter List ................................................................................. 6
Table 3: 100G QSFP28 ..................................................................................................... 8
Table 4: CHM-1 and CHM-2 DSP characteristics. ........................................................... 11
Table 5: CFP2-ACO characteristics. ................................................................................ 13
Table 6: QSFP28/+- pluggables mapped to Modules and Releases ................................ 14
Table 7: Latency of different modules and transmission modes (value range when difference
between packet size.) ............................................................................................... 17
1. Traffic Interfaces
The following Chapters describe the technical data of all transponder interfaces of Groove
G30 module sleds for 10G, 40G, and 100G optical channels.
STM-64
FC-10G
FC-16G
OC-192
100 GE
400 GE
FC-128
OTU-2
OTU-3
OTU-4
FC-2G
FC-4G
FC-8G
40 GE
FC-32
25GE
50GE
CHM1 X X
CHM2 X X X X X X X X X X X X
CHM1G X X
XTM2 x x x x x
Table 1: Overview of available client interfaces (note software release support must be
checked from Roadmaps)
4x10GBASE-
40Gbit/s QSFP+ 40GBASE-SR4 40GBASE-LR4 40GBASE-IR4
LR
81.71T- ZXS- ZXS-
Coriant part number (CFP) ZXS-QPI4ZZZZ
Q40GSR4 QPL4ZZZZ QPQ10GLW
Standard IEEE802.3ba IEEE802.3ba IEEE802.3bg IEEE802.3ba
0.1 (OM3 fiber)
Transmission distance km 0.15 (OM4 10 2 10
fiber)
MMF (ribbon
Fiber type / connector SMF / LC SMF / LC SMF
cable) / MPO
L0 1271 L0 1271
L1 1291 L1 1291
840 – 860 1310
Operating wavelength nm L2 1311 L2 1311
(4 x 10G opt) (4 x 10G opt)
L3 1331 L3 1331
(4 x 10G opt) (4 x 10G opt)
Bit rate (optical) Gbit/s 4 x 10.3125 4 x 10.3125 4 x 10.3125 4 x 10.3125
Bit rate (electrical) Gbit/s 4 x 10.3125 4 x 10.3125 4 x 10.3125 4 x 10.3125
Maximum Bit error rate 10-12 10-12 10-12 10-12
Transmitter VCSEL array CWDM-mux DFB-EAM 4xDFB-EAM
Laser Class 1m 1 1 1
Signaling speed variation ppm 100 100 100 100
SMSR dB 30 30 30
Av. Tx power (max) total dBm 8.3 8.3 8.3
Av. Tx power (max) / lane dBm 2.4 2.3 2.3 0.5
Av. Tx power (min) total dBm
Av. Tx power (min) / lane dBm -8 -7 -7 -8.2
Tx OMA ( / channel) dBm -6 -4 … 3.5 -4 … 3.5 -5.2 … 3.0
max diff. in Tx OMA / lane dB 6.5 6.5
Extinction ratio (min) dB 3 3.5 3.5 3.5
Transmitter Eye Mask IEEE802.3ba IEEE802.3ba IEEE802.3ba IEEE802.3ae
Optical path
Attenuation range min ...max dB 1.9 6.7 4 0 .. 6.2
IEEE-Tabl. 52-
Dispersion (max) ps/nm -59.5 .. 33.5 -59.5 .. 33.5
23
Optical RL Tolerance (max) dB 20 20 12
discrete reflectance (max) dB -21 -26 -26
DGD (max) ps 10 10 10
Demux –
Receiver PIN array PIN PIN array
PIN array
Mean input power (overload) (/ lane) dBm 2.4 2.3 2.3 0.5
max input power (damage) / lane dBm 3.4 3.3 3.3 1.5
sensitivity (min)/ lane OMA dBm -7.9 OMA -11.5 OMA -11.5 OMA -12.6
Max Difference in receive power
dB 7.5 7.5 7.5
(OMA) / lane
sensitivity (min) ( / lane) -9.5 -13.7 -13.7 -14.4
Stressed sensitiv. OMA/lane dBm -5.4 -9.6 -9.6 -10.3
Maximum Dispersion penalty dB 2.3 2.3 3.2
Receiver Reflectance (max) dB -12 -26 -26 -12
Note:
1) two different versions of are described one with 4dB extinction and one with 8dB extinction (the
one with 8dB extinction in parenthesis)
100GBASE-
100 Gbit/s QSFP28
PSM4
Coriant part number ZXS-
(QSFP28) Q8PSM4ZZ
100G PSM4
Standard
MSA
Transmission distance km 0.5
Fiber type / connector SSMF
Operating wavelengths nm 1295 to 1325
Bit rate (optical) Gbit/s 4 x 25.78125
Bit rate (electrical) Gbit/s 4 x 25.78125
CAUI-
Electrical / logical interface
4(IEEE802.3bm)
Maximum Bit error rate 10-12
DFB/EA array -
Transmitter
mux
Laser Class 1
Signaling speed variation ppm 100
SMSR dB 30
Av. Tx power (max) total dBm 8.0
Av. Tx power (max) / lane dBm 2
Av. Tx power (min) total dBm
Av. Tx power (min) / lane dBm -9.4
Tx OMA ( / channel) dBm -3.5
100GBASE-
100 Gbit/s QSFP28
PSM4
max diff. in Tx / lane dB 2.2 (OMA)
Extinction ratio (min) dB 3.5
Transmitter Eye Mask IEEE 802.3bm
Optical path SSMF
Attenuation range min
dB 6.2
...max
dispersion ps/nm
Maximum path penalty dB
Optical RL Tolerance
dB
(max)
DGD (max) ps
Demux – PIN
Receiver
array
Mean input power
dBm 2.0
(overload) (/ lane)
max input power (damage)
dBm 3.0
/ lane
sensitivity (min) OMA dBm -8.6
Max Difference in receive
dB 2.2 (OMA)
power / lane
sensitivity (min) ( / lane) -12.66
Stressed sensitiv.
dBm -9.8
OMA/lane
Receiver Reflectance
dB -26
(max)
CHM1 and CHM2 can support two coherent lines with 100G CP-QPSK, 150G 8QAM and
200G 16QAM formats. They use 200G CFP2-ACO line interfaces pluggables.
Please see here the parameters of the CHM-1 and CHM2-. (DSP in CHM-x defines
possible modulation formats, FEC, CD and PMD limits. CFP2-ACO pluggable creates
optical wavelength and defines TX and RX power limits, wavelength configurability etc.) :
1.12dB
OSNR penalty of dynamic
(DGD = 100 ps, SOPMD = 4000 ps2, ΔDGD = 100 ps/ms , ΔSOP =
PMD or/ and SOP
100 rad/ms,)
0.7 dB @ 2dB PDL
OSNR penalty for
2.1 dB @ 4dB PDL
Polarization dependent
3.7 dB @ 6dB PDL
Loss (PDL) (BER 10-3)
5.5 dB @ 8dB PDL
1
QPSK “15% FEC differential Everest-Compatible” rate is 120.58 Gbit/s, otherwise it would be 121.60 Gbit/s;
The following tables give an overview of the respective latency times: The traffic goes from
the client side to the line side, is doing a loop and goes back from the line side to the client
side. This means “total latency”.
Note that transmission delay in larger DWDM networks is mainly caused by the
transmission fibers and the used dispersion compensation fibers, only a minor contribution
is usually caused by the signal processing on the transponders cards.
CHM2 and CHM1G may use in addition encryption of the ODUx in transmission. Units
support two different encryption types, CTR and GMC. This encryption will cause
additional delay. ODU4 level encryption with CTR will cause 0.4 µs (400ns) extra latency
and ODU4 level GMC will have 3.2 µs extra delay. This latency must be added over
values in table below.
CHM2 n/a
CP-QPSK 100GE with FEC (GFP mode) OTU4V 25 % FEC 24.02 - 26.52
100GE with FEC (GFP mode) n/a
CP-QPSK OTU4V 15 % FEC 27.08 - 29.57
100GE with FEC (GFP mode) n/a
8QAM OTU3C 25 % FEC 21.29 - 23.78
100GE with FEC (GFP mode) n/a
16QAM OTU2C 25 % FEC 20.21 - 22.70
n/a
CP-QPSK 100GE without FEC (GFP mode) OTU4V 25 % FEC 23.86 - 26.35
100GE without FEC (GFP mode) n/a
CP-QPSK OTU4V 15 % FEC 26.9 - 29.39
100GE without FEC (GFP mode) n/a
8QAM OTU3C 25 % FEC 21.14 - 23.63
100GE without FEC (GFP mode) n/a
16QAM OTU2C 25 % FEC 20.04 - 22.53
n/a
CP-QPSK 100GE with FEC (GMP mode) OTU4V 25 % FEC 29.09
100GE with FEC (GMP mode) n/a
CP-QPSK OTU4V 15 % FEC 33.10
100GE with FEC (GMP mode) n/a
8QAM OTU3C 25 % FEC 26.41
CHM2 n/a
CP-QPSK 10GE (GFP mode) OTU4V 25 % FEC 26.85 – 42.62
10GE (GFP mode) n/a
CP-QPSK OTU4V 15 % FEC 30.48 – 46.26
10GE (GFP mode) n/a
8QAM OTU3C 25 % FEC 24.91 – 40.68
10GE (GFP mode) n/a
16QAM OTU2C 25 % FEC 23.87 – 39.63
n/a
CP-QPSK 10GE (GFP Preamble mode) OTU4V 25 % FEC 26.5 – 42.25
10GE (GFP Preamble mode) n/a
CP-QPSK OTU4V 15 % FEC 30.19 – 45.94
10GE (GFP Preamble mode) n/a
8QAM OTU3C 25 % FEC 24.65 – 40.39
10GE (GFP Preamble mode) n/a
16QAM OTU2C 25 % FEC 23.6 – 39.34
n/a
CP-QPSK 10GE (GMP mode) OTU4V 25 % FEC 34.64
10GE (GMP mode) n/a
CP-QPSK OTU4V 15 % FEC 38.62
10GE (GMP mode) n/a
8QAM OTU3C 25 % FEC 33.16
10GE (GMP mode) n/a
16QAM OTU2C 25 % FEC 31.77
CHM2 n/a
CP-QPSK OC-192/STM-64 (GMP mode) OTU4V 25 % FEC 35.8
OC-192/STM-64 (GMP mode) n/a
CP-QPSK OTU4V 15 % FEC 39.3
OC-192/STM-64 (GMP mode) n/a
8QAM OTU3C 25 % FEC 33.8
OC-192/STM-64 (GMP mode) n/a
16QAM OTU2C 25 % FEC 32.4
CHM2 n/a
CP-QPSK 8G/16G FC (GMP mode) OTU4V 25 % FEC 35.8
8G/16G FC (GMP mode) n/a
CP-QPSK OTU4V 15 % FEC 39.3
8G/16G FC (GMP mode) n/a
8QAM OTU3C 25 % FEC 33.8
8G/16G FC (GMP mode) n/a
16QAM OTU2C 25 % FEC 32.4
CHM2 n/a
CP-QPSK OTU2 (G709 FEC) OTU4V 25 % FEC 32.3
OTU2 (G709 FEC) n/a
CP-QPSK OTU4V 15 % FEC 35.8
Table 7: Latency of different modules and transmission modes (value range when difference
between packet size.)
2.1 ITU-T
G.656 Characteristics of a fibre and cable with non-zero dispersion for wideband optical
transport
G.957 Characteristics of a bending-loss insensitive single-mode optical fibre and cable for
the access network
G.959.1 Optical transport network physical layer interfaces
G.975.1 Forward error correction for high bit-rate DWDM submarine systems
G.692 Optical interfaces for multichannel systems with optical amplifiers
Channel spacing
G.693 Optical interfaces for intra-office systems
G.694.1 Spectral grids for WDM applications: DWDM frequency grid
G.694.2 Spectral grids for WDM applications: CWDM wavelength grid
G.695 Optical interfaces for coarse wavelength division multiplexing applications
G.698.1 Multichannel DWDM applications with single-channel optical interfaces
G.698.2 Amplified multichannel dense wavelength division multiplexing applications with
single channel optical interfaces
G.7041 Generic framing procedure (GFP)
G.709 Interfaces for the optical transport network (OTN)
G.798 Characteristics of optical transport network hierarchy equipment functional blocks
G.798.1 Types and characteristics of Optical Transport Network (OTN) equipment
G.805 Generic functional architecture of transport networks
NE modeling methodology
G.806 Characteristics of Transport Equipment – Description, Methodology and Generic
Functionality
G.8201 Error performance parameters and objectives for multi-operator international paths
within the Optical Transport Network (OTN)
G.826 End-to-end error performance parameters and objectives for international, constant
bit-rate digital paths and connections
G.870 Terms and definitions for optical transport networks (OTN) OTUk frame definition
G.872 Architecture of optical transport networks
Multiplexing hierarchy
G.874 Management aspects of the optical transport network element
G.957 Optical interfaces for equipments and systems relating to the synchronous digital
hierarchy
G.959.1 Optical transport network physical layer interfaces
G.975.1 Forward error correction for high bit-rate DWDM submarine systems
G.7710 Common equipment management function requirements
G.8010 Architecture of Ethernet layer networks
G.8021 Characteristics of Ethernet transport network equipment functional blocks
G.8031 Ethernet linear protection switching
G.8251 The control of jitter and wander within the optical transport network (OTN)
G.8261 Timing and synchronization aspects in packet networks
Synchronous Ethernet
G.8262 Timing Characteristics of Synchronous Ethernet Equipment Slave Clock (EEC):
limited to EEC-option 1.
G.8264. Distribution of Timing through Packet Networks: Layout of SSMs
G Suppl. 43 Transport of IEEE 10GBASE-R in optical transport networks (OTN)
2.2 IEEE
IEEE 754 IEEE Standard for Binary Floating-Point Arithmetic for microprocessor systems
IEEE 802.1AB Station and Media Access Control Connectivity Discovery Revision
IEEE 802.1ad Provider Bridges
QinQ
IEEE 802.1ag Connectivity Fault Management
IEEE 802.1ah Provider Backbone Bridges
IEEE 802.1D Media Access Control (MAC) Bridges
(Rapid) Spanning Tree Protocol
IEEE 802.1s Multiple Spanning Trees
IEEE 802.1x Port-Based Network Access Control
IEEE 802.3a Gigabit Ethernet for Metro Area Networks
IEEE 802.3ae 10Gb/s Ethernet
IEEE 802.3ah EFM: Ethernet in the First Mile
IEEE 802.3ba 40Gb/s and 100Gb/s Ethernet
IEEE 802.3bg 40Gb/s Ethernet Single-mode Fibre PMD
IEEE 8021 Characteristics of Ethernet transport network equipment functional blocks
IEEE 1149.1 IEEE Standard Test Access Port and Boundary Scan Architecture
IEEE 1588 / Standard for a Precision Clock Synchronization Protocol for Networked
1588v2 Measurement and Control Systems
RFC3415 View-based Access Control Model (VACM) for the Simple Network
Management Protocol (SNMP)
RFC3416 Version 2 of the Protocol Operations for the Simple Network Management
Protocol (SNMP)
RFC3417 Transport Mappings for the Simple Network Management Protocol (SNMP)
RFC3418 Management Information Base (MIB) for the Simple Network Management
Protocol (SNMP)
RFC3419 Textual Conventions for Transport Addresses
RFC3430 Simple Network Management Protocol Over Transmission Control
Protocol Transport Mapping
RFC3434 Remote Monitoring MIB Extensions for High Capacity Alarms
RFC3635 Definitions of Managed Objects for the Ethernet-like Interface Types
RFC3636 Definitions of Managed Objects for IEEE 802.3 Medium Attachment Units
(MAUs)
RFC3768 Virtual Router Redundancy Protocol (VRRP)
RFC3826 The Advanced Encryption Standard (AES) Cipher Algorithm in the
SNMP User-based Security Model
RFC4253 The Secure Shell (SSH) Transport Layer Protocol
RFC4330 Simple Network Time Protocol (SNTP) Version 4 for IPv4, IPv6 and
OSI
RFC4363 Definitions of Managed Objects for Bridges with Traffic Classes, Multicast
Filtering, and Virtual LAN Extensions
RFC4836 Definitions of Managed Objects for IEEE 802.3 Medium Attachment Units
(MAUs)
End of document