Professional Documents
Culture Documents
WIMA MP 3-X2
Metallized Paper (MP)
RFI-Capacitors Class X2
PCM 10 mm to 27.5 mm
˜ Particularly high reliability against Capacitance range: Maximum pulse rise time:
active and passive flammability 1000 pF to 1.0 mF (E12-values on request) Capacitance Pulse rise time V/msec
˜ Excellent self-healing as well as Rated voltages: pF/mF max. operation
high voltage strength 250 VAC, 275 VAC
˜ High degree of interference Capacitance tolerances: 1000 1000
suppression due to good ±20% 1500 600
attenuation and low ESR Operating temperature range: 2200 ... 4700 450
˜ For temperatures up to +110° C –40) C to +110) C 6800 ... 0.022 300
˜ According to RoHS 2002/95/EC Climatic test category: 0.033 ... 0.047 200
40/110/56/C in accordance with IEC 0.068 ... 1.0 100
Typical Applications Insulation resistance at +20+ C: for pulses equal to the rated voltage,
C 0.33 mF: 12 x 10 3 M¸ Upp = 390 V
Class X2 RFI applications to meet C > 0.33 mF: 4000 sec (M¸ x mF) Test voltage: 2700 VDC, 2 sec.
EMC regulations Measuring voltage: 100 V/1 min. Reliability:
˜ Capacitors connected to the mains Dissipation factors: Operational life > 300 000 hours
between phase and neutral or tan d 13 x 10 –3 at 1 kHz and +20+ C Failure rate < 1 fit (0.5 x U r and 40) C)
phase and phase conductors Test specifications:
˜ Installation category II in In accordance with DIN EN 132 400
accordance with IEC 60664, Approvals:
pulse peak voltage 2.5 kV Approval-No. Approval-No.
Country Authority Specification Symbol
250 VAC 275 VAC
Construction
Germany VDE DIN EN 132 400 V 89749 89749
D E
Dielectric: IEC 60384-14/2 EN 132 400
Capacitor paper
Vacuum-deposited
electrode Mounting Recommendation Packing
Metal contact layer
(schoopage)
Terminating wire To minimize or avoid shock and/or Available taped and reeled up to and
vibration stresses to terminating wires including PCM 22.5 mm.
and solder connections we recommend to
fix voluminous resin-potted MP capacitors Detailed taping information and graphs
as from e.g. PCM 22.5 mm in an at the end of the catalogue.
Encapsulation: appropriate way since for constructional
Self-extinguishing epoxy resin, UL 94 V-0, reasons they do not sit tight on the For further details and graphs please
metal foil board. refer to Technical Information.
Terminations:
Tinned wire.
Marking:
Marking: Black on Silver.
10.05
91
D
WIMA MP 3-X2
Continuation
General Data
250 VAC* 275 VAC*
Capacitance
W H L PCM** W H L PCM**
1000 pF 4 8.5 13.5 10 4 8.5 13.5 10
1500 „ 4 8.5 13.5 10 4 8.5 13.5 10
2200 „ 4 8.5 13.5 10 4 8.5 13.5 10
3300 „ 4 8.5 13.5 10 4 8.5 13.5 10
4700 „ 5 10 13.5 10 5 10 13.5 10
6800 „ 5 13 19 15 5 13 19 15
0.01 mF 5 13 19 15 5 13 19 15
0.015 „ 5 13 19 15 5 13 19 15
0.022 „ 5 13 19 15 5 13 19 15
0.033 „ 6 14 19 15 6 14 19 15
0.047 „ 7 15 19 15 7 15 19 15
0.068 „ 8 17 19 15 8 17 19 15
0.1 mF 10 18 19 15* 10 18 19 15*
8 20 28 22.5* 8 20 28 22.5*
0.15 „ 8 20 28 22.5 8 20 28 22.5
0.22 „ 10 22 28 22.5 10 22 28 22.5
0.33 „ 12 24 28 22.5 12 24 28 22.5
0.47 „ 13 25 33 27.5 13 25 33 27.5
0.68 „ 15 26 33 27.5 15 26 33 27.5
1.0 mF 20 32 33 27.5 20 32 33 27.5
* f = 50/60 Hz 10
Z
** PCM = Printed circuit module = lead spacing S
1 --
7 10
Upon request with long leads 35-2 mm max. 5
-- --
--
22
00
-- 6 00 pF
3 80 70 4
0. 0 pF
-- 0
0. 22
01
0.47 ---- 1.0
15 -
0.
0. p p PC
* On ordering please state the required PCM (lead spacing). -- 02 µF F F
M
--
0.1 0. 2 10
µF
-
-- 04
--
7 µ
1 F PC
0.
5
33 CM
µ
µF M
15
µF
3
P
PC 5
Dims. in mm.
M
27
22
.5
0.01
0.1 3 5 7 1 3 5 7 10 3 5 7 100 1000
Taped version see page 100. f/MHz
W L
6 -2
d = 0.7 P if PCM 10 d PCM
d = 0.8 P if PCM 15 at the lead exit
Rights reserved to amend design data without prior notification. points
( 0.5)
10.05
92
D
Soldering Process
Wave soldering
[°C] 10 s
A preheating of through-hole WIMA T
ISO 9001:2000 is an international basic All WIMA capacitors, irrespective of According to the RoHS Directive 2002/95/EC
standard of quality assurance systems for whether through-hole devices or SMD, certain hazardous substances like e.g. lead,
all branches of industry. The approval are made of environmentally friendly cadmium, mercury must not be used any
according to ISO 9001:2000 of our materials. Neither during manufacture longer in electronic equipment as of July 1st,
factories by the VDE inspectorate certifies nor in the product itself any toxic sub- 2006. For the sake of the environment WIMA
that organisation, equipment and moni- stances are used, e.g. has refraind from using such substances since
toring of quality assurance in our factories – Lead – PBB/PBDE years already.
correspond to internationally recognized – PCB – Arsenic
standards. – CFC – Cadmium
– Hydrocarbon chloride – Mercury
WIMA WPCS – Chromium 6+ – etc.
We merely use pure, recyclable materials
The WIMA Process Control System (WPCS)
for packing our components, such as:
is a quality surveillance and optimization
system developed by WIMA. WPCS is a
major part of the quality-oriented WIMA ” carton
production. Points of application of WPCS ” cardboard
during production process: ” adhesive tape made of paper
” polystyrene Tape for lead-free WIMA capacitors
” incoming material inspection
” metallization
” film inspection We almost completely refrain from using
” schoopage packing materials such as: ISO 14001:2005
” pre-healing
” lead attachment ” foamed polystyrene (Styropor®) WIMA’s environmental management has
” cast resin preparation/ ” adhesive tapes made of plastic been established in accordance with the
encapsulation ” metal clips guidelines of ISO 14001. The certification
” 100% final inspection is under preparation and is expected to be
” AQL check accomplished by June 2006.
06.05
16
D
P1
W2
H1
H
Diagram 1:
W0
W1
PCM 2.5/5/7.5mm
W
D0
d
F
P0
P
t
P
H1
P1 P1
H
d d
F P0 P2 P0
P2 F
Position of components according to PCM 7.5 (sketch 1). P 0 = 12.7 or 15.0 is possible
100