Professional Documents
Culture Documents
CM C1_09KD-S/Md 12/98 1
Function description CM (C1_O7/C1_09)
This Software Version can be used in electric-, as well as in
gas units.
To use this Software Version in gas units, it is necessary to install
a link permanently on connector X8 (of the CPU pcb) between ter-
minal 1 and 2 before changing the Software Version or carrying out
a Total Reset.
Version C1_07 can only be used in processor pcb without
extended memory
Version C1_09 can only be used in processor pcb with exten-
ded memory
1. Mode switch
After switching on the unit to any mode, the LED of the chosen
mode lights up and the green “on” indicator turns on.
STEAM O
HOT AIR
COMBI STEAM
VARIO STEAM
REHEATING
PROG C
taken over. On the timer display “0.” will be displayed and the
buzzer sounds. If the timer was set to “d.” (continuous running),
before the power failure, the unit remains on “d.”.
O
C) The timer display shows „0.“ and the buzzer sounds, when 120.
the cabinet door is closed or „d.“ if the dial was set to this
position befor the unit was switched on. O
12
D) Or by pressing the core temperature symbol first it is possi-
ble to select core temperature. 80
The upper core temperature display shows the actual
temperature of the meat probe. O
The lower core temperature display shows the preset core tem-
perature.
It is possible to select a core temperature between
20 - 99°C with the dial.
CM C1_09KD-S/Md 12/98 3
E) Indication of actual cooking values:
During running a cooking mode or a program, the
interior cabinet temperature push button will be pres-
sed, the following actual cooking values will be shown
flashing dot.
Indication “unit too hot” will come on after 2 minutes when the
temperature remains above 150°C, the thermocouple is defect or
the temperature of the steam generator is below -5°C.
CM C1_09KD-S/Md 12/98 5
3. Vario-steam mode 30 - 99 °C
Indication “unit too hot” will come on after 2 minutes when the
temperature remains above 150°C, the thermocouple is
defect or the temperature of the steam generator isbelow -5°C.
CM C1_09KD-S/Md 12/98 7
4.6 Temperature control of steam generator
The steam generator temperature is measured by the thermocouple
B5 on steam heater. When the thermocouple reaches a temperatu-
re of 150°C, the steam heaters will be switched off immediately.
Steam heating will be switched on again when the temperature
drops below 150°C.
Indication “unit too hot” will come on after 2 minutes when the
temperature remains above 150°C, the thermocouple is
defect or the temperature of the steam generator is below -5°C.
CM C1_09KD-S/Md 12/98 9
6. Hot air mode 30 - 300°C
6.3 During Hot air mode indication "lack of water" will not
be
shown.
Cool down
Procedure:
7.1 Select mode on which you like to change quenching
temperature, LED of cooresponding symbol will illuminate.
7.2 Press and hold down interior cabinet temperature and core 70
temperature push button (for more than 10 sec.). Keep both
push buttons pressed during the whole procedure.
Memorized quenching temperature will be shown on actual and
70
preset core temperature display simultaneously O
7.3 With both push buttons still pressed turn the core temperature
dial to zero position. Now the required quenching temperature 80
can be selected (range between 50 and 120°C) with the core tem-
perature dial (e.g. 80°C). 70
7.4 On the upper core temperature display the new quenching tempe- O
rature (e.g. 80°C) will be shown.
On the lower core temperature display the old quenching tempera-
ture (e.g. 70°C) will be indicated.
CM C1_09KD-S/Md 12/98 11