Professional Documents
Culture Documents
MGB1359F-Respiraderos de Techo Tipo Hongo
MGB1359F-Respiraderos de Techo Tipo Hongo
9-15510
for Grain Bins
Installation Instructions
A BROCK® “Mushroom” Roof Vent provides 1.25 sq. ft. [.116 m ] of opening.
2
CAUTION! For a Vacuum System, venting must be added at the rate of 1 sq. ft. [.093 m ] 2
4 Item Description
1 Manhole Panel
2 Manhole
3 1 3 Roof Ladder Panel
4 Vent
2
Figure 1.
Installation
1.Remove the three 1/4" Jam Nuts (Item 7) and 1/4" Weatherseal Washers (Item 9) that
attach the Lid Assembly (Item 5) to the Vent Body (Item 2). See Figure 2.
2.Remove the Lid Assembly.
3.Set the Vent Body Assembly on the Roof Sheet (Item 1) at the desired location
(Figure 2). Vents should be installed before assembling Roof Panels. Refer to Charts
for Stiffener Ring placement and avoid this area.
IMPORTANT! Remember to avoid the Stiffener Ring location.
2 MGB1359E
BROCK® Mushroom Roof Vent
7
Item Part No. Description Qty.
3 9-15510 Vent Assembly
1 - Roof Panel
2 9-15503 Vent Body 1
2 3 9-15507 Lid Mounting Bracket 3
4 9-15506 Vent Screen 1
SIDE VIEW 5 9-15511 Vent Lid Assembly 1
4 6 39-20004 Bolt, Hex Head 1/4-20 x 1'' Gr. 2 9
7 39-20019 Nut, Jam 1/4''-20 12
8 39-20058 Washer, Flat 5/16'' 3
9 39-20154 Washer, Weatherseal 1/4'' 3
6 9-15509 Roof Vent Mounting Kit
7 7 39-20019 Nut, Jam 1/4''-20 12
9 39-20154 Washer, Weatherseal 1/4'' 12
6 10 39-20297 Washer, Flat 1/4'' 12
2
7 11 39-48274 Bolt, Hex Head, 1/4-20 x 1'' Gr. 5 12
8 6 12 9-33678 Caulking 10' [3 048]
7
4.Draw or scribe line around the inside of the Vent Body on the
Roof Panel. See Figure 4.
5
TOP VIEW
2 1
2
CUT
Figure 3.
Exploded View
1/2''
[13]
Figure 4. SCRIBE
Cut Out a Circle 1
5.Cut a hole in the Roof Sheet, leaving about 1/2" [13] of metal inside the scribe line.
6.Place two (2) stacked beads of Caulking on the outside of the scribe line as shown in
Figure 2 above.
7.Set the Vent Body Assembly back in place and drill twelve (12) 5/16" [7.9] diameter
mounting holes in the Roof using the Vent Body Holes as pilot holes.
8.Use twelve (12) 1/4 x 1" Gr. 5 Hex Head Bolts (Item 11) to hold the Vent Body Assembly
in place. Place the 1/4" Flat Washers (Item 10) under the Bolt heads. Place
1/4" Weatherseal Washers (Item 9) between the Roof Panel and 1/4" Jam Nuts (Item 7).
Tighten all Bolts. See Figure 1 and Detail. (continued on last page)
MGB1359E 3
BROCK® Mushroom Roof Vent
9.Bend the inside Roof Panel lip up on the scribe line using a hammer. See Detail.
Hammer the lip up all the way around at about a 45º angle. Hammer around again
bringing it up to 90º, close to the Vent Body.
10.Replace the Lid Assembly, Washers and Nuts, and tighten.
Different by Design™
BROCK GRAIN SYSTEMS
A Division of CTB Inc.
P.O. Box 2000 • Milford, Indiana 46542-2000 • U.S.A.
Phone (574) 658-4191 • Fax (574) 658-4133
e-mail: brock@brockmfg.com • Internet: http://www.brockgrain.com
and
7400 East Thirteenth Street, Kansas City, Missouri 64126 U.S.A.
Phone (816) 968-6101 FAX: (816) 968-6272 TLX: 6841105Printed in the U.S.A.