Professional Documents
Culture Documents
Can be used solely or with Conplast WP400*† for water- Appearance : Brown solution
proof, structural and precast concrete. Specific gravity : 1.18 at 25°C
Chloride content : Nil to BS 5075 / BS:EN934
Advantages
Instructions for use
Does not incorporate bitumen.
Compatibility
Provides integral protection, ensuring reduced permea-
bility throughout the concrete. Conplast WP200 is compatible with other Fosroc admix-
tures used in the same concrete mix. All admixtures should
Integral protection is maintained even if surface damage
be added to the mix separately and must not be premixed
occurs, unlike applied surface films or coatings.
together prior to addition. The resultant properties of mixes
Lower water:cement ratio improves compressive containing more than one admixture should be assessed by
strength at same workability. the trial mix procedure recommended on this data sheet.
Fully compatible with certain Fosroc surface coatings Conplast WP200 is suitable for use with all types of Portland
and finishes. cements, SRC cements and cement replacement materials
such as PFA, GGBFS and microsilica.
Description
The use of a combination of admixtures in the same con-
Conplast WP200 chloride free permeability reducing ad- crete mix and or cement replacements may alter the setting
mixture is based on a formulated blend of dispersants. It is time. Trials should always be conducted to determine such
supplied as a brown solution which instantly disperses in setting times.
water.
Dispensing
The dispersants in Conplast WP200 improve the effective-
The correct quantity of Conplast WP200 should be meas-
ness of water in the concrete mix, enabling desired levels
ured by means of a recommended dispenser. The admixture
of workability to be obtained with lower water contents. This
should then be added to the concrete with the mixing water
produces a mix with a reduced water:cement ratio and
to obtain the best results. Contact the Fosroc Technical
therefore reduced permeability.
Service Department for advice regarding suitable equipment
and its installation.
Technical support
Curing
Fosroc provides a technical advisory service for on-site as-
sistance and advice on admixture selection, evaluation trials As with all structural concrete, good curing practice should
and dispensing equipment. Technical data and guidance can be maintained, particularly in situations where an overdose
be provided for admixtures and other products for use with has occurred. Water spray, wet hessian or a Concure*†
fresh and hardened concrete. spray applied curing membrane should be used.
The optimum dosage of Conplast WP200 to meet specific Many variables in concreting materials and conditions can
requirements should always be determined by trials using affect the selection and use of an admixture. Trials should
the materials and conditions that will be experienced in use. be carried out using relevant materials and conditions in
This allows the optimisation of admixture dosage and mix order to determine the optimum mix design and admixture
design and provides a complete assessment of the mix. The dosage to meet specific requirements.
normal recommended dosage is 0.40 to 0.75 litre per 100 kg
Because of the variability of concreting materials, the results
of cement.
should only be taken as typical of the performance to be ex-
Conplast WP200
Effects of overdosing pected. Results quoted are not necessarily directly compa-
rable with results obtained elsewhere for Conplast
An overdose of Conplast WP200 may result in increased
WP200 or other products.
retardation and workability.
Fosroc Conplast WP200
Important note
Fosroc products are guaranteed against defective materials and manufacture and are sold subject to its standard Conditions for the Supply of
Goods and Service. All Fosroc datasheets are updated on a regular basis. It is the user’s responsibility to obtain the latest version.
Head Office
telephone: (+9714) 2039699 fax: (+9714) 2859649 email: agf@fosroc.com
Al Gurg Fosroc LLC
Regional offices
Post Box 657, Dubai Abu Dhabi, Al Gurg Fosroc telephone: 673 1779 fax: 673 1449 email: abudhabi@fosroc.com
Bahrain, YBA Kanoo telephone: 17738200 fax: 17732828 email: bahrain@fosroc.com
United Arab Emirates Kuwait, Boodai telephone: 4817618 fax: 4832124 email: kuwait@fosroc.com
Oman, Al Amana telephone: 24815080 fax: 24817554 email: oman@fosroc.com
www.fosroc.com Qatar, Tadmur telephone: 4665501 fax: 4664147 email: qatar@fosroc.com
UAE/0231/15/G