Professional Documents
Culture Documents
Training:
CSWIP 3.0 : Certificate no.66216
CSWIP 3.1 : Certificate no.107452
Relevant More than 10 years experiences in EPC company relation with oil and gas. Duties and
Experience responsibility involve in quality control.
Responsibilities:
-Check filler metals and consumable materials.
-Check correct welding performance parameters observed.
-Monitor joint fit-up and visual inspection.
-Review inspection document to ensure completed NDE requirement.
Responsibilities:
-Review Hydrostatic Test Package documents and release for Hydro test.
-Verify flange bolt tightening performed and tag as required before hydro Test.
-Check calibration records for gauges and other measurements used for testing.
-Ensure all exclusion items were removed and replaced by temporary spools or isolated
with blind prior to perform flushing and Hydro testing.
-Perform hydro testing as per approved procedure.
-Perform Draining and Drying after Hydro test.
-Ensure piping components in lines and dropped items that were removed for hydro test
are reinstated and Hydro Test blind & all Temporary supports were removed.
-Verify flow direction, Orientation of Valve installed are correct as per IFC drawing & P&ID
and ensure all punch "B, C " are close out. Verify bolt/nut/gasket correct size, rating,
flange face cleanliness and perform flange bolt tightening (Flange Management) after
hydro test.
-Perform final reinstatement verification and Test package approval.
Responsibilities:
-Monitoring welder qualifications test.
-Check filler metals and consumable materials.
-Check correct welding performance parameters observed.
-Monitor joint fit-up and visual inspection.
-Review inspection document to ensure completed NDE requirement.
-Performs other duties as described under supervisor master title.
Responsibilities:
-Monitor joint fit-up and visual inspection.
-Check correct welding performance parameters observed.
-Performs other duties as described under supervisor master title.
Responsibilities:
-Perform inspect of material receive and MTR reviewed.
-Monitoring welder qualifications test.
-Check filler metals and consumable materials.
-Monitor joint fit-up and visual inspection.
-Review inspection document to ensure completed NDE requirement.
-Inspection blast and protective coating.
-Perform MDR compilation.
Responsibilities:
-Perform inspect of material receive and MTR reviewed.
-Monitoring welder qualifications test.
-Check filler metals and consumable materials.
-Monitor joint fit-up and visual inspection.
-Review structure package to ensure completed NDE requirement.
-Inspection blast and protective coating.
-Perform MDR compilation.
Responsibilities:
-Operate furnace for post weld heat treatment (PWHT)
-Manage and planning measuring device to calibrations.
-Perform internal audit as per ISO 9001 standard.
Responsibilities:
-Perform MDR compilation.
Responsibilities:
-Prepare quality document i.e. ITP, NDE procedure and fabrication procedure.
Responsibilities:
Welding practice process SMAW, GTAW, FCAW
Responsibilities:
-Monitor joint fit-up and visual inspection.
-Check correct welding performance parameters observed.
Responsibilities:
-Monitor joint fit-up and visual inspection.
-Check correct welding performance parameters observed.
-Monitoring hydrostatic test for piping.
Responsibilities:
-Prepare quality document i.e. ITP, NDE procedure and fabrication procedure.
-Perform inspect of material receive and MTR reviewed.
-Monitoring welder qualifications test.
-Check filler metals and consumable materials.
-Monitor joint fit-up and visual inspection.
-Review piping package to ensure completed NDE requirement prior to hydrostatic test.
-Monitor Plumpness, Roundness, Peaking, Banding, Air test, Penetration oil test for tank.
-Prepare tank hydrostatic test package.
-Monitoring hydrostatic test for piping and storage tanks.
-Inspection blast and protective coating.
-Perform MDR compilation.
Responsibilities:
-Prepare materials take off and prepare cutting plan.
-Perform inspect of material receive and MTR reviewed.
-Perform paint estimate and prepare paint instruction.
Responsibilities:
-Piping line check prior to hydrostatic test.
-Review piping package to ensure completed NDE requirement prior to hydrostatic test.
-Monitor hydrostatic test for piping.
-Reinstatement inspection prior to commissioning.
Responsibilities:
-Inspection for tank shell rolling and spherical shell pressing.
-Monitoring welder qualifications test.
-Check filler metals and consumable materials.
-Monitor joint fit-up and visual inspection.
-Check correct welding performance parameters observed.
-Perform inspection Plumpness, Roundness, Peaking, Banding, Air test, Penetration oil
test.
Responsibilities:
-Monitoring welder qualifications test.
-Check filler metals and consumable materials.
-Monitor joint fit-up and visual inspection.
-Check correct welding performance parameters observed.
-Review piping package to ensure completed NDE requirement prior to hydrostatic test.
-Monitoring hydrostatic test for storage tanks and piping.
-Inspection blast and protective coating.
Responsibilities:
-Perform inspect of material receive and MTR reviewed.
-Monitoring bending material for roof assembly.
-Monitoring welder qualifications test.
-Check filler metals and consumable materials.
-Monitor joint fit-up and visual inspection.
-Check correct welding performance parameters observed.
-Inspection blast and protective coating.
-Perform MDR compilation.
Jan. 2007 - Aug. 2007 Employer Qualitech Engineering and Construction Co.,Ltd.
Position QA/QC Engineering
Project Vincent Project (Vetco Ibel)
Type of work Structural Module, Piping
Responsibilities:
-Perform inspect of material receive and MTR reviewed.
-Monitoring welder qualifications test.
-Check filler metals and consumable materials.
-Monitor joint fit-up and visual inspection.
-Check correct welding performance parameters observed.
-Inspection blast and protective coating.
-Perform MDR compilation.
Responsibilities:
-Prepare Process Chart and Process Quality Control.
-Training Operation Standard and Quality Control Standard prior to initiate working of
operator.
-Solve and prepare work instruction of operator.
-Reduce and Improvement product repair.
Computer Skill Microsoft Office (Excel, Word, Power Point) and Auto Cad
QA/QC Manager
Company: QMTS
Contact No. 0813779422