Professional Documents
Culture Documents
Placa Parterdemisol 1
Placa Parterdemisol 1
22 1
60 2
50 3
100 4
5
582,65
100 6
7
50 8
Commercial use only with Plus-, PDF- or Profi-Option (from 2.99 € / month plus VAT).
200 9
10
0 20 40 60 80 100 120 140 160 180 200 220 240 260 280 300 320 340 360 mm
08 95 au nd ,1
41 V O ub esta U=0
N z e
DI ut 4N VB nd us
ch V1 EnE esta bau ha
es E siv
är
m En 20
B
Ne u
u
5 Pa
s
W 20 V16 uba =0,2 ,15
E G E N e U . U =0
G n
E 20 MV aßn us
20 San elm 5 5
0, 2 r - Ha
G E inz fW 40 -Lite
GE U=
W
E
au K BW K fW 3
Kf eub eG au
N ärm ub
EW Ne
*Compare to minimal requirements of Bodenflächen gegen Erdreich from the annexure of Energieeffizient Sanieren. Page 1
All statements without guarantee
Temperature profile
Temperature profile
Temperature
www.ubakus.de
30
1 2 3 4 5 6 7 Dew point
28
8 9
26
24
Temperature [°C]
22
20
18
16
14
12
10
Commercial use only with Plus-, PDF- or Profi-Option (from 2.99 € / month plus VAT).
Inside [mm]
www.ubakus.de Outside
1 Parchet lemn (22 mm) 4 Placa betoon armat (100 mm) 7 Folie hidroizolatie
2 Sapa interior (60 mm) 5 Folie PE 8 Sapa de egalizare (50 mm)
3 Austrotherm EPS - A200 (50 mm) 6 Austrotherm XPS Top 30 (100 mm) 9 Pietris (200 mm)
Left:Temperature and dew-point temperature at the place marked in the right figure. The dew-point indicates the
temperature, at which water vapour condensates. As long as the temperature of the component is everywhere above the dew
point, no condensation occurs. If the curves have contact, condensation occurs at the corresponding position.
Right: The component, drawn to scale.
Page 2
All statements without guarantee
Moisture proofing
For the calculation of the amount of condensation water, the component was exposed to the following constant climate for
90 days: inside: 20°C und 50% Humidity; outside: 10°C und 100% Humidity (Climate according to user input).
This component is free of condensate under the given climate conditions.
Commercial use only with Plus-, PDF- or Profi-Option (from 2.99 € / month plus VAT).
Humidity
The temperature of the inside surface is 20,0 °C leading to a relative humidity on the surface of 41%.Mould formation is not
expected under these conditions.
The following figure shows the relative humidity inside the component.
www.ubakus.de
Relative humidity (%)
100
1 2 3 4 5 6 7 saturation point
90
8 9
80
Relative humidity (%)
70
60
50
40
30
20
10
0
0 100 200 300 400 500 600
Inside [mm]
www.ubakus.de Outside
1 Parchet lemn (22 mm) 4 Placa betoon armat (100 mm) 7 Folie hidroizolatie
2 Sapa interior (60 mm) 5 Folie PE 8 Sapa de egalizare (50 mm)
3 Austrotherm EPS - A200 (50 mm) 6 Austrotherm XPS Top 30 (100 mm) 9 Pietris (200 mm)
Notes: Calculation using the Ubakus 2D-FE method. Convection and the capillarity of the building materials
were not considered. The drying time may take longer under unfavorable conditions (shading, damp / cool
summers) than calculated here.
Page 3
All statements without guarantee
heating level
Heat output into the interior (heating output): approx. 13 W/m².
The heating plane leads to increased heat losses to the outside and can be taken into account with an effective U-value
(Ueff):
Effective u-value: 0,45 W/m²K (Energy loss of the heated component)
This document has been generated by the U-value calculator on www.ubakus.de. If you are harmed by the free use of these contents, the service provider is only liable in case of
outside:
At the assumed temperatures of room air, outside air and heating plane, the heat loss to the outside corresponds to an
identical but unheated component with an U-value of Ueff =0,45 W/m²K.
Temperature of inside surface: 23,3 °C
These values are based on an average water temperature in the heating plane of 30 °C, a room temperature of 20 °C and an
outside temperature of 10 °C.
Commercial use only with Plus-, PDF- or Profi-Option (from 2.99 € / month plus VAT).
Page 4