Professional Documents
Culture Documents
outside
3 4
50 3
313
www.ubakus.de
240 2
Commercial use only with Plus-, PDF- or Profi-Option (from 2.99 € / month plus VAT).
20 1
inside
1 Cement plaster (20 mm) 3 ISOVER Kontur FSP 1-032 (50 mm)
2 Ytong Planblock W PP 6-0,65 (240 mm) 4 External plaster (3 mm)
0 20 40 60 80 100 120 140 160 180 200 220 240 260 280 300 mm
8 i
0 95 eT
u
ba =0,2 d
5
=0
,1
41 O ig u
DI
N tzV dr Ne U n sU
hu nie 1 4 e sta au
es
c
n d V B nd u ivh
m ta E nE EV sta uba s s
är
B e s E n
B e Ne Pa
W u ,2
EV 20 16 ba =0 ,15
En 20 EV Neu V U . =0
G n
E 20 n U
GE nM aß us 40
20 ESa elm 5 - Ha KfW
G z 5 r
GE e
Ein fW BW -Lit bau
f W u K eG 3 u
K ba ärm Ne
u
Ne EW
*Vergleich mit dem Höchstwert gemäß GEG 2020 für erstmaligen Einbau, Ersatz oder Erneuerung von Außenwänden (Anlage 7, Zeile 1a,1b). Page 1
All statements without guarantee
Temperature profile
Temperature profile
15 Temperature
1 2 3 4 Dew point
10
-15
-20
Commercial use only with Plus-, PDF- or Profi-Option (from 2.99 € / month plus VAT).
www.ubakus.de Outside
Temperature and dew-point temperature in the component. The dew-point indicates the temperature, at which water vapour
condensates. As long as the temperature of the component is everywhere above the dew-point temperature, no
condensation occurs. If the curves have contact, condensation occurs at the corresponding position.
Page 2
All statements without guarantee
Moisture proofing
For the calculation of the amount of condensation water, the component was exposed to the following constant climate for
90 days: inside: 15°C und 60% Humidity; outside: -18°C und 60% Humidity (Climate according to user input).
This component is free of condensate under the given climate conditions.
Humidity
The temperature of the inside surface is 12,4 °C leading to a relative humidity on the surface of 71%.Some kinds of mould
start to grow at relative air humidities of 70% or more, mould cannot be excluded!. To avoid mould formation, the surface
Commercial use only with Plus-, PDF- or Profi-Option (from 2.99 € / month plus VAT).
temperature should be increased by (additional) insulation.
The following figure shows the relative humidity inside the component.
Page 3
All statements without guarantee
Heat protection
The following results are properties of the tested component alone and do not make any statement about the heat protection
of the entire room:
Temperature profile
This document has been generated by the U-value calculator on www.ubakus.de. If you are harmed by the free use of these contents, the service provider is only liable in case of
32
30 1 Cement plaster (20 mm)
Temperature [°C]
Commercial use only with Plus-, PDF- or Profi-Option (from 2.99 € / month plus VAT).
16
14
0 50 100 150 200 250 300
Inside [mm]
www.ubakus.de Outside
Phase shift* 14,5 h Heat storage capacity (whole component): 201 kJ/m²K
Amplitude attenuation ** 84,7 Thermal capacity of inner layers: 151 kJ/m²K
TAV *** 0,012
* The phase shift is the time in hours after which the temperature peak of the afternoon reaches the component interior.
** The amplitude attenuation describes the attenuation of the temperature wave when passing through the component. A value of 10
means that the temperature on the outside varies 10x stronger than on the inside, e.g. outside 15-35 °C, inside 24-26 °C.
*** The temperature amplitude ratio TAV is the reciprocal of the attenuation: TAV = 1 / amplitude attenuation
Note: The heat protection of a room is influenced by several factors, but essentially by the direct solar radiation through windows and the
total amount of heat storage capacity (including floor, interior walls and furniture). A single component usually has only a very small
influence on the heat protection of the room.
Page 4