Professional Documents
Culture Documents
10 1
50 2
150 3
322,5
100 4
12,5 5
Commercial use only with Plus-, PDF- or Profi-Option (from 2.99 € / month plus VAT).
1 Lamination (10 mm) 3 Reinforced concrete (150 mm) 5 Gypsum board (12,5 mm)
2 Cement screed (50 mm) 4 Expanded polystyrene (100 mm)
0 20 40 60 80 100 120 140 160 180 200 220 240 260 280 300 mm
8 95 u d ,1
41
0 ba an =0
N zV
O eu est d U
DI u t N B n u us
ch 14 EV ta ha
es nEV En Bes uba ss
iv
m E Ne u
är 20 5 5 Pa
W 20 V16 uba =0,2 = 0,1
G E e
GE En 20 N V U ßn. sU
20 San elm
M a 5 2 H au
G 5 0 , r -
GE E inz W
Kf W U= 40 -Lite
E u B f W 3
W a
Kf eub eG uK
N ärm uba
EW Ne
*Comparison to the maximum U-value according to the german EnEV 2014/2016 for first-time installation or renewal of Decken nach unten gegen Page 1
Erdreich oder unbeheizte Räume (Anlage 3, Tabelle 1, Zeile 5a).
All statements without guarantee
Temperature profile
Temperature profile
20 Temperature
1 2 3 4 5 Dew point
18
16
1 Lamination (10 mm)
Temperature [°C]
14
2 Cement screed (50 mm)
12 3 Reinforced concrete (150 mm)
10 4 Expanded polystyrene (100 mm)
8 5 Gypsum board (12,5 mm)
6
4
2
0 50 100 150 200 250 300 350
Inside [mm]
Commercial use only with Plus-, PDF- or Profi-Option (from 2.99 € / month plus VAT).
www.ubakus.de Outside
Temperature and dew-point temperature in the component. The dew-point indicates the temperature, at which water vapour
condensates. As long as the temperature of the component is everywhere above the dew-point temperature, no
condensation occurs. If the curves have contact, condensation occurs at the corresponding position.
Page 2
All statements without guarantee
Moisture proofing
For the calculation of the amount of condensation water, the component was exposed to the following constant climate for
90 days: inside: 20°C und 50% Humidity; outside: 5°C und 80% Humidity (Climate according to user input).
This component is free of condensate under the given climate conditions.
Humidity
The temperature of the inside surface is 18,9 °C leading to a relative humidity on the surface of 54%.Mould formation is not
Commercial use only with Plus-, PDF- or Profi-Option (from 2.99 € / month plus VAT).
expected under these conditions.
The following figure shows the relative humidity inside the component.
Page 3
All statements without guarantee
Heat protection
The following results are properties of the tested component alone and do not make any statement about the heat protection
of the entire room:
Temperature profile
This document has been generated by the U-value calculator on www.ubakus.de. If you are harmed by the free use of these contents, the service provider is only liable in case of
32
30 1 Lamination (10 mm)
Temperature [°C]
Commercial use only with Plus-, PDF- or Profi-Option (from 2.99 € / month plus VAT).
16
14
0 50 100 150 200 250 300 350
Inside [mm]
www.ubakus.de Outside
Phase shift* 7,8 h Heat storage capacity (whole component): 420 kJ/m²K
Amplitude attenuation ** 96,2 Thermal capacity of inner layers: 368 kJ/m²K
TAV *** 0,010
* The phase shift is the time in hours after which the temperature peak of the afternoon reaches the component interior.
** The amplitude attenuation describes the attenuation of the temperature wave when passing through the component. A value of 10
means that the temperature on the outside varies 10x stronger than on the inside, e.g. outside 15-35 °C, inside 24-26 °C.
*** The temperature amplitude ratio TAV is the reciprocal of the attenuation: TAV = 1 / amplitude attenuation
Note: The heat protection of a room is influenced by several factors, but essentially by the direct solar radiation through windows and the
total amount of heat storage capacity (including floor, interior walls and furniture). A single component usually has only a very small
influence on the heat protection of the room.
Page 4