Professional Documents
Culture Documents
outside
20 3
280
240 2
www.ubakus.de
Commercial use only with Plus-, PDF- or Profi-Option (from 2.99 € / month plus VAT).
20 1
inside
1 Cement plaster (20 mm) 2 Ytong Planblock W PP 6-0,65 (240 mm) 3 Cement plaster (20 mm)
08 95 Ti ba
u 5 5
41 O ige 0,2 nd 0,1
tzV dr eu =
U sta =
DI
N
u ie 4 N u s U 40
ch dn 1 Be nd uba au fW
es n EV EV t a e 0,2 r- H K
är
m sta En En Bes 16 N bau V U= . ite au
W V
Be 20 EV eu M ßn 3-L eub
EnE 20 En 20 N San lma N
G E ze 55 W
GE 20
EG Ein KfW eG B
G W
Kf bau ärm
u EW
Ne
*Vergleich mit dem Höchstwert gemäß GEG 2020 für erstmaligen Einbau, Ersatz oder Erneuerung von Außenwänden (Anlage 7, Zeile 1a,1b). Page 1
All statements without guarantee
Temperature profile
Temperature profile
22 Temperature
20 1 2 3 Dew point
18
16 1 Cement plaster (20 mm)
Temperature [°C]
14
2 Ytong Planblock W PP 6-0,65 (240 mm)
12
3 Cement plaster (20 mm)
10
8
6
4
2
0
-2
0 50 100 150 200 250 300
Inside [mm]
Commercial use only with Plus-, PDF- or Profi-Option (from 2.99 € / month plus VAT).
www.ubakus.de Outside
Temperature and dew-point temperature in the component. The dew-point indicates the temperature, at which water vapour
condensates. As long as the temperature of the component is everywhere above the dew-point temperature, no
condensation occurs. If the curves have contact, condensation occurs at the corresponding position.
Page 2
All statements without guarantee
Moisture proofing
For the calculation of the amount of condensation water, the component was exposed to the following constant climate for
90 days: inside: 22°C und 60% Humidity; outside: 5°C und 60% Humidity (Climate according to user input).
This component is free of condensate under the given climate conditions.
Humidity
The temperature of the inside surface is 19,4 °C leading to a relative humidity on the surface of 70%.Some kinds of mould
start to grow at relative air humidities of 70% or more, mould cannot be excluded!. To avoid mould formation, the surface
temperature should be increased by (additional) insulation.
Commercial use only with Plus-, PDF- or Profi-Option (from 2.99 € / month plus VAT).
The following figure shows the relative humidity inside the component.
Page 3
All statements without guarantee
Heat protection
The following results are properties of the tested component alone and do not make any statement about the heat protection
of the entire room:
Temperature profile
This document has been generated by the U-value calculator on www.ubakus.de. If you are harmed by the free use of these contents, the service provider is only liable in case of
36
Temperature at 3pm, 11am and 7am
34
1 2 3 Temperature at 7pm, 11pm and 3am
intent and gross negligence on the part of the service provider. For further information, please refer to the terms and conditions at https://www.ubakus.de/agb
32
30 1 Cement plaster (20 mm)
Temperature [°C]
Commercial use only with Plus-, PDF- or Profi-Option (from 2.99 € / month plus VAT).
16
14
0 50 100 150 200 250 300
Inside [mm]
www.ubakus.de Outside
Phase shift* 12,2 h Heat storage capacity (whole component): 236 kJ/m²K
Amplitude attenuation ** 15,0 Thermal capacity of inner layers: 108 kJ/m²K
TAV *** 0,067
* The phase shift is the time in hours after which the temperature peak of the afternoon reaches the component interior.
** The amplitude attenuation describes the attenuation of the temperature wave when passing through the component. A value of 10
means that the temperature on the outside varies 10x stronger than on the inside, e.g. outside 15-35 °C, inside 24-26 °C.
*** The temperature amplitude ratio TAV is the reciprocal of the attenuation: TAV = 1 / amplitude attenuation
Note: The heat protection of a room is influenced by several factors, but essentially by the direct solar radiation through windows and the
total amount of heat storage capacity (including floor, interior walls and furniture). A single component usually has only a very small
influence on the heat protection of the room.
Page 4