Professional Documents
Culture Documents
outside
30 6
100 5
12,5 4
367,5
200 www.ubakus.de
3
Commercial use only with Plus-, PDF- or Profi-Option (from 2.99 € / month plus VAT).
15
10 1 2
inside
100 625
50 625
1 Cement plaster (10 mm) 4 Knauf Gipsfaserplatte Vidiwall 12,5mm (12,5 mm)
2 OSB (15 mm) 5 Knauf Insulation Fassaden-Dämmplatte TP 432 B (100 mm)
3 Biofib Trio (200 mm) 6 Steel (30x0.6)
OSB
Knauf Gipsfaserplatte Vidiwall 12,5mm Equivalent
insulation thickness
Knauf Insulation Fassaden-Dämmplatte TP 432 B (WLS 038)
0 20 40 60 80 100 120 140 160 180 200 220 240 260 280 300 320 340 360 mm
0 8 95 Ti u
ba =0,2 d
5 ,1
41 O ige u =0
DI
N tzV dr NeU tan sU
ch
u nie 14 s ha
u
e s n d E V Be nd au iv
m st a E n E V ta b ss
är Be En Bes Neu u Pa
W 0 ,2
E V 2 1 6 ba =0 ,15
En 20 EV Neu V U . =0
G n
E 20 n U
GE nM aß s 40
20 ESa elm 5 Ha u fW
G 5 - K
GE
z er
Ein fW BW -Lit bau
f W u K eG 3 u
K a Ne
e ub ärm
N EW
*Vergleich mit dem Höchstwert gemäß GEG 2020 für erstmaligen Einbau, Ersatz oder Erneuerung von Außenwänden (Anlage 7, Zeile 1a,1b). Page 1
All statements without guarantee
Temperature profile
Temperature profile
20 Temperature
18 Dew point
1
16
2 3 4 5 6
14
12
Temperature [°C]
10
8 outside
6
4
2
0
-2
-4 www.ubakus.de
-6
-8
0 50 100 150 200 250 300 350 400 inside
[mm]
Inside www.ubakus.de 0°C
Commercial use only with Plus-, PDF- or Profi-Option (from 2.99 € / month plus VAT).
Outside 100 625
1 Cement plaster (10 mm) 3 Biofib Trio (200 mm) 5 Knauf Insulation Fassaden-Dämmp...
2 OSB (15 mm) 4 Knauf Gipsfaserplatte Vidiwall 12... 6 Outside air (30 mm)
Left:Temperature and dew-point temperature at the place marked in the right figure. The dew-point indicates the
temperature, at which water vapour condensates. As long as the temperature of the component is everywhere above the dew
point, no condensation occurs. If the curves have contact, condensation occurs at the corresponding position.
Right: The component, drawn to scale.
Page 2
All statements without guarantee
Moisture proofing
For the calculation of the amount of condensation water, the component was exposed to the following constant climate for
90 days: inside: 20°C und 50% Humidity; outside: -5°C und 80% Humidity. This climate complies with DIN 4108-3.
This component is free of condensate under the given climate conditions.
Commercial use only with Plus-, PDF- or Profi-Option (from 2.99 € / month plus VAT).
36,75 cm Whole component 1,58 251,3
Humidity
The temperature of the inside surface is 17,5 °C leading to a relative humidity on the surface of 58%.Mould formation is not
expected under these conditions.
The following figure shows the relative humidity inside the component.
70
60 outside
50
40
30
20 www.ubakus.de
10
0
0 50 100 150 200 250 300 350 400 inside
[mm]
Inside www.ubakus.de 0°C Outside 100 625
1 Cement plaster (10 mm) 3 Biofib Trio (200 mm) 5 Knauf Insulation Fassaden-Dämmp...
2 OSB (15 mm) 4 Knauf Gipsfaserplatte Vidiwall 12... 6 Outside air (30 mm)
Notes: Calculation using the Ubakus 2D-FE method. Convection and the capillarity of the building materials
were not considered. The drying time may take longer under unfavorable conditions (shading, damp / cool
summers) than calculated here.
Page 3
All statements without guarantee
Heat protection
The following results are properties of the tested component alone and do not make any statement about the heat protection
of the entire room:
Temperature profile
This document has been generated by the U-value calculator on www.ubakus.de. If you are harmed by the free use of these contents, the service provider is only liable in case of
32 2 3 4 5 6
30 1 Cement plaster (10 mm)
Temperature [°C]
Commercial use only with Plus-, PDF- or Profi-Option (from 2.99 € / month plus VAT).
16
14
0 50 100 150 200 250 300 350 400
Inside [mm]
www.ubakus.de Outside
Phase shift* 13,1 h Heat storage capacity (whole component): 138 kJ/m²K
Amplitude attenuation ** 71,9 Thermal capacity of inner layers: 113 kJ/m²K
TAV *** 0,014
* The phase shift is the time in hours after which the temperature peak of the afternoon reaches the component interior.
** The amplitude attenuation describes the attenuation of the temperature wave when passing through the component. A value of 10
means that the temperature on the outside varies 10x stronger than on the inside, e.g. outside 15-35 °C, inside 24-26 °C.
*** The temperature amplitude ratio TAV is the reciprocal of the attenuation: TAV = 1 / amplitude attenuation
Note: The heat protection of a room is influenced by several factors, but essentially by the direct solar radiation through windows and the
total amount of heat storage capacity (including floor, interior walls and furniture). A single component usually has only a very small
influence on the heat protection of the room.
The calculations presented above have been created for a 1-dimensional cross-section of the component.
Page 4