Professional Documents
Culture Documents
HVAC COATINGS,
ADHESIVES & SEALANTS
CONTENTS
1. PROFILE
2. CERTIFICATES
a) Commercial Registration Certificate
b) Industrial License Certificate
c) Chamber of Commerce Registration Certificate
d) Zakath Certificate
e) ISO Certificate
3. PRODUCT RANGE
4. DATA SHEETS
I. HVAC DUCT COATINGS
a) Dellag LA 3-36 – Lag Seal Insulation Protection Coating
b) Dellag LA 65 AF – Anti Fungal Insulation Protection Coating
II. VAPOR BARRIER COATINGS
a) Delvap VB 3-80 – Vapor Barrier Insulation Coating
b) Delvap VB 3-85 AF – Anti Fungal Vapor Barrier Coating
III. HVAC DUCT ADHESIVES
a) Delfix 8-10 – Premium Duct Liner Adhesive
b) Delfix 8-65 – Superior Quality Duct Liner Adhesive
IV. HVAC DUCT SEALANTS
a) Delseal 3-17 – Superior Fibrated Duct Sealant
5. TEST REPORTS
a) Dellag LA 3-36
b) Delvap VB 3-85 AF
c) Delfix 8-10
d) Delseal 3-17
CERTIFICATES
DELMON CHEMICAL INDUSTRIES
Specialty Chemicals Division
PRODUCT RANGE
HVAC COATINGS
• DELLAG LA 3-36
Lag Seal Insulation Protection Coating
• DELLAG LA 65 AF
Anti Fungal Insulation Protection Coating
DELLAG LA 3-36
LAG SEAL INSULATION PROTECTION COATING
PROFilE TECHNICALDATA
DELLAGLA 3-36 is a tough, white, abrasion
Solid Content : 58 t 1%
resistant, washable protective coating for
thermal insulations. DELLAGLA 3-36 exhibits (ASTMD 1644)
excellent adhesion, weather and UVresistance Viscosity @ 25°C : 80,000-100,000cps
properties and is ideal for application as a (Brookfield)
white lagging finish, lap adhesive and coating.
DELLAGLA 3-36 has excellent brushability SpeCific Gravity : 1.32 t 0.05
which provides uniform, even coverage and (ASTMD 1475)
will not discolor with age. Water Vapor Permeability: Q.78 Metric-
(ASTME96) Permsat 0.8 mm
USAGE
DELLAGLA3-36 is recommended as a durable Surface Burning Characteristics (ASTM E 84)
protective and lag seal coating for insulations Flame Spread : 2
over different types of air conditioning ducts
Smoke Developed : 0.25
and cold water piping, when applied in
multiple coats over different type of thermal Drying Time at 25°C and 50% RH.
insulations along with fiberglass, canvas or (ASTMD 1640 )
other suitable lagging cloths or reinforcements : 2 hrs
embedded in between two coats. DELLAGLA Touch Dry
3-36 also can be used over polystyrenefoam, Dry Through : 8 hrs
polyurethane foam and other foam : -20°C to + 100°C
insulations. Service Temperature
Wet Flammability : Non Flammable
OUTSTANDINGFEATURES (ASTM D 3278)
...
Tough and durable
Excellent tensile strength and elongation Wet FilmThickness (WFT): 0.8Smm to O.5mm
Solar and heat reflective per Literl Coat
..
Excellent weather and UVresistance
Withstands temperatures -20°C to +1OO°C
Dry FilmThickness (DFT) : O.Smmto O.3mm
per Literl Coat
.. Environmental friendly
Asbestos free and non hazardous
Non toxic, non flammable and solvent free
DELLAG LA 3-36 meets the requirements of
MIL-A 3316 C/D,Class 1 I Grade A.
PACKING
5 USgallon pail INSTAllATION PROCEDURE
a. General
STORAGE
1. DELLAG LA 3-36 can be applied by a brush,
Store under cover preferably above +SOCand roller or airless spray. For airless
spray, select a
below +30°(, Keep away from direct sunlight nozzle size of 0.028'(0.70 mm). Ensure the
and frost. Close the container tightly when not suitability of the equipment prior to
in use.
application.
c. Application
1. Apply an even first coat of DELLAGLA 3-36 Wherever required, the application rate of
at 1.2 to 2.0 M2 per liter (70 to 80 sq. ft per DELLAG LA 3-36 can be increased to enhance
gallon). the final applied coating thickness.
2. Embed the lagging fabric or reinforcement The actual dry film thickness of the application
into the wet coating and impregnate. Smooth may vary with the type of reinforcement used.
out to avoid wrinkles and .ensure 5 cm
overlapping at all seams. Always test foils and paper facing for adhesion
requirements, prior to application. Never
3. Apply top coat of DELLAG LA 3-36 apply DELLAG LA 3-36, if rain is imminent.
immediately at coverage of 1.2 to 2.0 M2 per
liter (70 to 80 sq. ft per gallon). Ensure the DELLAG LA 3-36 contains no asbestos, lead,
lagging cloth or reinforcement is fully covered mercury or any other hazardous materials.
with the top coat.
HEALTH AND SAFETY
Actual coverage may vary, depend on the type,
nature and evenness of the surface and the Generally safe, non toxic and non flammable in
wet condition. However, avoid prolonged skin
application method.
contact. Use of gloves is advisable. If eyes are
affected with DELLAG LA 3-36, rinse with
Additional protection of vapor barrier is excess amount of clean fresh water. If
recommended for application or installation at
areas where the relative atmospheric humidity ingested, seek medical attention immediately.
level is higher than 75% for prolonged period Ventilation to the working area is desirable..
or the installed pipeline contains refrigerant,
brine, chilled water etc.
SURFACEBURNING CHARACTERISTICSASTM E 84
TESTEDAT UNDERWRITERSLABORATORIESINC, USA @
~'"""
Surface 6.4 mm (\ inch) High Density
Inorganic Reinforced Cement Board
2.0
"~'"""
Flame Spread*
Smoke
Developed
0.25 W~/~
Number of
1
". ~'='"
Coats
"'. ~
Test Coverage
Rate 60sq.ft. per Gallon ~. ) ""..
* The flame spread may vary at different product thickness and or when applied over different substrates.
Theinformation contained in the technical data sheet is proL,jded based on our besl knoll'ledge and current lerel of information 10assist tbe Itsage of tbe malerial without any liability
or guarantee. Often the product is used under conditions beyond our control, U'f?can not guarantee anything. bUI tbe produCt itself. The user is adl.'ised 10 ensure tbe suitability and
safety of tbeproducifor an)' parlicular applicalion.
Delmon Chemical Industries, Specialty Chemicals Division, P.O. Box 6800. Dammam 31452, Saudi Arabia
Tel: +96638121771 (5 Lines), Fax: +96638121705, E-mail: dcichem@delmon.com.sa, Websire: www.delmon.com.sa
• DELVAP VB 3-80
Vapor Barrier Insulation Coating
• DELVAP VB 3-85 AF
Anti Fungal Vapor Barrier Coating
DELMON CHEMICAL INDUSTRIES
Specialty Chemicals Division
DUCT ADHESIVES
• DELFIX 8-10
Premium Duct Liner Adhesive
• DELFIX 8-65
Superior Quality Duct Liner Adhesive
DELFIX 8-10
PREMIUM DUCT LINER ADHESIVE
/ DELFIX 8-10
PREMIUM DUCT LINER ADHESIVE
APPLICATION CLEANING
Apply DELFIX 8-10 uniformly over the Clean brush and equipment with chlorinated
substrate at 4.90 to 11.50 M2/L, leaving no bare solvent (non flammable), mineral spirit
spots including joints, lapping, screw points (flammable) or other suitable solvents.
etc. and press insulation material firmly into
place. Ensure complete contact is made HEALTH AND SAFETY
between the insulation and applied adhesive.
Insulation should be fixed within 10 minutes Avoid skin contact. Use of glove is advisable. If
from adhesive application. ingested, do not induce vomiting, seek medical
attention immediately. Ventilation to the
Overhead applications may require standard working area is desirable.
mechanical fasteners.
• The flame spread may vary at different product thickness and or when applied over different substrates.
Tbe information conrQl1led in the technical data sbeet ;s prot'jded based on our best knowledge and current Jerel oj information to assist tbe usage of the material u-ithout any liability
or guarantee Often (be product is used under conditions beyond our control, u'e can not guarantee anything. but tbe product itself The user is adrised to ensure the suitabilirJ and
safety of tbe product for any particular application
Delmon Chemical Industries, Specialty Chemicals Division, P.O. Box 6800, Dammam 31452, Saudi Arabia
Tel: +96638121771 (5 Lines), Fax: +96638121705, E-mail: dcichem@delmon.com.sa, Website: www.delmon.com.sa
DUCT SEALANTS
• DELSEAL 3-17
Superior Fibrated Duct Sealant
DELSEAL 3-17
SUPERIOR FIBRATED DUCT SEALANT
PROFILE TECHNICALDATA
DELSEAL 3-17 is a fire resistivefibrated water Solid Content : 72:!:: 1%
resistant low shrinkage durable single (ASTMD 1644)
component vapor barrier sealant for low, : 1.46:!:: 0.05
Specific Gravity
medium and high velocity heating and air (ASTMD 1475)
conditioning ducts. DELSEAL3-17forms tough
permanently flexible and durable seal against Surface Burning Characteristics (ASTME 84)
air leakage when applied with or without
reinforcement tape. Flame Spread : 4
.
DELSEAL 3-17
SUPERIOR FIBRATED DUCT SEALANT
Flame Spread* .4
Smoke
a
Developed
Number of
Coats 1
* The flame spread may vary at different product thickness and or when applied over different substrates.
The inforllla,;on contained in the technical data sbeetis prol'ided based 011our best knou'ledge and currenrJerel of information to assist the IIsageof tbe material wi/bout any liability
or guarantee. Of/en tbe product is llsed under condilions beyond our control. u'e can not guarmlfee anytb;1lg.bUltbe product itself. The user is adl'ised to ensure tbe suitability and
safely of tbe produCi for any particular application.
TEST REPORTS
DELMON CHEMICAL INDUSTRIES
Specialty Chemicals Division
Delfix 8-10,
6 King Khaled Medical City Riyadh Zuhair Fayez Partnership Saudi Arabian Baytur
Delseal 3-17
Delfix 8-15,
7 Al Battoyor Tower Dammam Zuhair Fayez Partnership Ibrahim A. Asmael Est.
Delseal 3-17
King Saud Bin Abdulaziz University - Delfix 8-10,
8 Riyadh Elkhereiji Company
University Main Campus Project Delseal 3-17
Page 1 of 4
DELMON CHEMICAL INDUSTRIES
Specialty Chemicals Division
The following are the few major projects accomplished with Delmon HVAC products
Sl.
Project Product Location Consultant Contractor
No:
Delfix 8-10,
9 University of Dammam Dammam Zuhair Fayez Partnership Al Zahrani Trading & Contracting
Delseal 3-17
Dellag LA 3-36
10 Al Majdouie HQ Complex Delfix 8-10 Dammam Suhaimi Design Ibrahim A. Asmael Est.
Delseal 3-17
Dellag LA 3-36
Dellag LA 65-AF
King Fysal University - Boys & Girls
11 Delfix 8-10 Al Hassa Al Batten
Activity Center
Delfix 8-15
Delseal 3-17
King Fahad University for Petroleum & Dellag LA 3-36,
12 Minerals (Students Housing - Phase 3 Delfix 8-10, Dammam Al Yamama Co.,
& 4) Delseal 3-17
13 Zamel Turbag Office Building Dellag LA 3-36 Al Khobar Zamel Turbag Consultants Ibrahim A. Asmael Est.
14 Al Falak Housing Compound Dellag LA 3-36 Al Khobar Ibrahim A. Asmael Est.
15 Aryaf Foods Central Factory Dellag LA 3-36 Dammam Gulf Consults Ibrahim A. Asmael Est.
Royal Commission (P & C of Delfix 8-10
16 Jubail APTC Contracting Co. Ltd.
Operation & Maintenance Center) Delseal 3-17
17 Al Mutlaq Complex Delfix 8-10 Al Khobar Saudi Designers Engg. ConsultantsIbrahim A. Asmael Est.
18 Technical College Delseal 3-17 Hafer Al Batin Abdullah Al Syed Est.,
Dellag LA 3-36
19 Al Mutawa Tower Delfix 8-10 Riyadh Samama for Pre-Cast
Delseal 3-17
Page 2 of 4
DELMON CHEMICAL INDUSTRIES
Specialty Chemicals Division
The following are the few major projects accomplished with Delmon HVAC products
Sl.
Project Product Location Consultant Contractor
No:
Dellag LA 3-36
Delfix 3-85 AF
20 Durat Al Bahrain Bahrain WS Atkins Al Kamed Engineering Services Co.,
Delfix 8-10
Delseal 3-17
Dellag LA 3-36
21 Imam University Delfix 8-10 Riyadh TYPSA Al Fozan Contracting
Delseal 3-17
Dellag LA 3-36
22 King Fysal University Delfix 8-10 Riyadh Beurohappad AZARB
Delseal 3-17
Dellag LA 3-36
23 Al Waseer Center Delfix 8-10 Riyadh Khatib Alami TAROUK
Delseal 3-17
Dellag LA 3-36
24 Riyadh Pension Fund Project Delfix 8-10 Riyadh Al Biya Al Latifia Contracting
Delseal 3-17
Dellag LA 3-36
25 Muthawa Tower Delfix 8-10 Riyadh Khatib & Alami SAAMA
Delseal 3-17
Dellag LA 3-36
26 Emergency Center - National Guard Delfix 8-10 Riyadh National Guard SAPAC
Delseal 3-17
Page 3 of 4
DELMON CHEMICAL INDUSTRIES
Specialty Chemicals Division
The following are the few major projects accomplished with Delmon HVAC products
Sl.
Project Product Location Consultant Contractor
No:
Dellag LA 3-36
28 Eastern Province Cement Co., (EPCC) Delfix 8-10 Al Khobar Radicon - Gulf Consult A. A. Al Turki Corporation (ATCO)
Delseal 3-17
Royal Commission (Jubail Industrial Delfix 8-10
29 Jubail A. A. Al Turki Corporation (ATCO)
College - JIC) Delseal 3-17
31 Bisha Airport Delseal 3-17 Bisha Nesma Al Fadl Contracting Co. Ltd.,
Page 4 of 4
DELMON CHEMICAL INDUSTRIES
Specialty Chemicals Division
HVAC PRODUCTS